Best Barns USA Assembly Book Revised March 6, 2017 the Arlington Building Size 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted. Under the copyright laws, this manual may not be copied, in whole or in part, without consent from Reynolds Building Systems, Inc.
IMPORTANT INFORMATION ABOUT YOUR SHED KIT This manual will show the assembly for the Arlington building kit. See back page for the breakdown of this material. If you received duplicate books, use the one with the latest revision date. The foundation is 12'-0" x 15'-9". Do Not make the foundation larger. Read the instructions before starting the assembly of the building. If you have any questions about assembling the kit, call 800-245-1577. Business hours (8:00-5:00 ET) Monday thru Friday.
Constructing Details for Deluxe Floor System Deluxe floors include 4x4 runners, standard floors do not Shown below is a typical wood floor. Depending on your area, the construction may have to be changed to meet local codes. When using a concrete slab for a floor, use the same overall foundation measurements. Install foam sill sealer as a moisture barrier between the concrete and the wall plates. Foam sill sealer is available in rolls, 3-1/2" or wider. 1. Cut (2) two 2x4 joist headers to 15' - 9".
Step 1 Assemble Roof Trusses 1. Locate a 2x4 -12' board, with angle cuts on both ends, to be used for the truss bottom. 2. Position 105-3/4" long pre-cut 2x4 rafters on the 12' board. 3. Temporarily tack 2x4 blocks, packed in kit, around the truss members. This will insure that the trusses are built exactly the same. 4. Position a 2x4-17-1/2" block at the ridge. 5. Position a 16-3/4" long 2x4 gable stud at each end of the truss.
Step 2 Assemble Roof Gables 1. Select another 12' long 2x4, with angle cuts on both ends. Install pre-cut rafters and bottom gussets as in previous step. Install the bottom gussets on one side only. 2. Install 38-3/4" and 50" long 2x4 gable studs. Secure gable studs with 1" x 4" metal drive-on plates. 3. Install the upper wood gusset, on one side. 4. Position a 2x4-17-1/2" block at the ridge. 1x4 Drive-on Plate 50" Gable Stud 38-3/4" Gable Stud 1x4 Drive-on Plate 4.
Step 3 Install Siding on Gables 1. Cut a 4x8 siding panel in half creating (2) two 48" siding panels. Install one of the pieces with the 'LAP' edge flush with the end of the bottom 2x4 board and extending 3/4" below the bottom 2x4. Cut siding flush with the top of the gable frame. Secure with 6d galv. nails. 2. Cut a 4x8 siding panel to a length of 66-1/2". Save the cutoff. Install the siding in the center. Cut siding flush with the top of the gable frame. 3.
Step 5 Assemble 12' Back Wall (without door opening) 1. Position (4) four 2x4-72" boards together and indicate with 'X' marks, where the wall studs will be located. X X 23-1/4" X X 72" Top Wall Plate 24" X X X X X X 72" Bottom Wall Plate 23-1/4" X X 24" X X X X 2x4-72" Wall Plate Pre-cut Wall Studs ottom 72" B Plate 2. Install pre-cut wall studs between the top & bottom plates. Pre-cut wall studs will be 92-5/8" or 92-1/4" in length.
Step 6 Assemble 92-1/2" Long Sidewall 1. Cut (2) two 2x4-8' to a length of 92-1/2". Position the boards together and indicate with 'X' marks where the wall studs will be located. 19-3/4" X X 92-1/2" Wall Plates X X 24" 24" X X 2. Install pre-cut wall studs between the top & bottom plates. Nail studs to wall plates with 10d sinkers, (2) two nails on each end.
Step 7 Assemble 89-1/2" Long Sidewall 1. Cut (2) two 2x4-8' to a length of 89-1/2". Position the boards together and indicate with 'X' marks where the wall studs will be located. 23-1/4" X X 89-1/2" Wall Plates X X 24" X X 24" 2. Install pre-cut wall studs between the top & bottom plates. 3. Butt wall farme to wall panel from previous step. Do Not nail these frames together so they can be separated later. 4.
Step 9 Assemble 12' Front Wall (with door opening) 1. Gather the material listed below to assemble the door wall. 8 4 1 1 Pre-cut Wall Studs 2x4-6' Boards Door Header from Step 8 2x4 Block 2x4+6' 2x4+6' nail nail Door Header 2. Install (6) six pre-cut wall studs between the 2x4-6' boards where shown. Temporarily secure the bottom 2x4-6' boards together with a 2x4 block. Cut pre-cut studs and install under door header on both sides Install Stud in Center Screw 2x4 block with 3" wood screws. 3.
Step 10 Layout Sidewall Plates for Walk-in Door Centered Cut (2) two 16' long 2x4 boards to a length of 15'-2"'. Indicate with 'X' marks where the wall studs will be located. Wall frame will be assembled in next step.
Step 11 Assemble Sidewall 1. Install (10) ten pre-cut wall studs between the 2x4s. 2. Install a pre-built door header, packed in dormer carton, between the center wall studs. Nail through top plate. Use 10d sinkers. 3. Cut (2) two pre-cut wall studs to fit as support for header and install. Secure to studs. Use 10d sinkers.
Step 12 Apply Siding to Sidewall Frame 1. Measuring from the 'Tongue Edge' cut a siding panel to a width of 46-1/2". Install this panel with the cut edge extending 3-1/2" past the left end of the wall frame. The siding should extend 3/4" below the wall plate. 4. Install a full width siding panel. Locate where you want the window and cut the opening. 5. Install another siding panel. Cut the siding out of the door opening, flush with the side frame and top header. LAP Edge 6. Install another siding panel.
Step 14 Set Wall Panels 1. Set the sidewall panels without door between the front and back walls. Secure wall panels together at the corners. Use (4) four 10d coated nails per corner. Nail through the bottom plate to secure walls. Do not nail in door opening. Space 10d sinkers 24" apart. 2. Nail along the siding edge where the sidewall panels overlap. 3. Install the sidewall with door opening between the front and back walls. Do not nail to floor in door opening. 4.
Step 15 Install 2x4 Tie Plates 1. Cut (2) two 2x4-16' boards to a length of 15'-9" and install on the sidewalls, as shown below. Use 10d sinkers. 2. Cut a 6' long 2x4 in half and install 3' long 2x4s on the 12' front and back walls as shown below. Cut to fit and install a 6' long 2x4 between the 3' long 2x4s. 2x4-15-9"' Tie Plate Cut 2x4-6' to Fit 2x4-3' Tie Plate Step 16 2x4-15'-9"' Tie Plate Install Corner Trim IMPORTANT: Lower Trim Must Be Installed Before Installing Roof Gables! 1.
Step 17 Layout Roof Trusses 2. From the first line, draw more lines 24" apart and put an 'X' to the side of these lines. This will place the trusses 24" on center. 3. When installing trusses, position the wood gusset on edge of the line. Back Wall Measure from outside of 1x4 Trim 24" 1. Measuring from back wall trim. Draw a line where the trusses will be positioned. Mark an 'X' to the side of this line. 22-3/8" 1x4 Trim 24" Important: When installing trusses place the gusset on the line.
Step 19 Set Trusses 1. Starting from back gable install (4) four trusses with the wood gusset on edge of line and the truss bottom over the 'X' marks. 2. Secure trusses with the metal hangers and 1-1/2" long hanger nails. IMPORTANT Secure the trusses to the sidewall that has the wall bracing first. Make sure the opposite sidewall is plumb before securing trusses. The building width should be 12'-0" measuring outside of 2x4 tie plate to outside of 2x4 tie plate.
Step 21 Install Sidewall Trim & Soffit It is easier to install the soffit if the corner and sidewall trim are installed first. This enables the soffit to rest on the trim where it meets the building. See lower detail. 1. Install a 96-3/4" long 1x4 trim board flush with the corner trim on the back of the building. This trim board has blue paint on one end. Locate a 7/16" x 3" x 8" gauge block packed in the hardware bag. Place this gauge block under the truss overhang and butt the corner trim against it.
Step 22 Install 1x6 Fascia on Sidewalls 1. Starting from back gable install a 121-1/2" long 1x6 trim board flush with the face 2x4 overhang. Install the 1x6 board so the face of the board is aligned with the top of the trusses. Use a straight edge as shown below. Use 8d galv. nails. 2. Cut to fit a 1x6-8' board flush with the 2x4 overhang on the front gable. 3. Repeat on opposite sidewall. Straight Edge 1x6 Fascia Board Step 23 Install Sheathing over Sidewall (without door) 1.
Step 24 Install Roof Sheathing for Dormer side 1. Install 4x8 roof sheathing per layout below 2. Install 1x6 trim on the end gables, flush with the top of the 2x4s. Use 8d galv. nails, spaced 12". Plyclip 48" x 48" 1x6 Gable Trim 48" x 96" End Wall You can cut the dormer openings as you install the roof sheathing. See Step 2 in the Dormer Assembly Book, packed in the dormer kit, for the opening sizes.
Step 25 Install Front Gable Trim and Door Trim 1. Install 1x6 trim boards over the 2x4 boards, flush with the top of the 2x4s. 1x6 Gable Trim 3-7/8" Wide Jamb Material 80-3/4" Long 1x4 Door Trim Complete the steps below if you are installing wood pocket doors. 1. 2. 3. 4. Install 3-7/8" x 72" white pine wide jamb material on the top of the door opening. Install 3-7/8" x 79-1/4" white pine wide jamb material on the sides of the door opening.
Install Roofing — Not Supplied in Kit 1. Install metal roof edging along the end walls and the front edge of the roof sheathing. Metal Roof Edge Roof Sheathing m 6 2x4 Overhang 1x i Tr 2. Install shingles according to the instructions on the wrapper. If you need more detailed instructions on installing shingles, there are good publications at book stores or newsstands.
Material Packaged In Component Kit Qty. Material Packaged In Component Kit Qty.