INSTALLATION INSTRUCTIONS HB0078 CP35 AND CP37 SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 and 13. BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711 REGISTER YOUR PRODUCT ON LINE AT: www.BestRangeHoods.com/register For additional information - visit www.BestRangeHoods.com SV08544 rev.
! WARNING ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
- CP35 AND CP37 POWER PACK SYSTEM MODEL 634 OR 644 (ROOF CAP) MODEL 437 (HIGH CAPACITY ROOF CAP) MODEL 441 (10’’ ROUND WALL MODEL 643 (8” ROUND WALL CAP) CAP) MODEL 418 (10” ROUND ADJUSTABLE ELBOW) 8” ROUND ADJUSTABLE ELBOW 8” ROUND MODEL 410 (10” ROUND DUCT —2 FT.
1. PREPARE THE INSTALLATION CAUTION When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
4. MOUNT CUSTOM HOOD INTERNAL FRAMEWORK ! WARNING The framework must be positively secured to wall studs or other wooden framework behind the drywall. Make sure it is capable of supporting its own weight and the weight of the CP35 or CP37. Failure to do so may cause personal injury or damage to countertop or cooktop. The CP35 and CP37 power pack is supported by the custom hood internal framework with screws provided in parts bag.
7. REMOVE THE BOTTOM PANEL Using a Phillips screwdriver, remove both bottom panel retaining screws and set aside. Disassemble bottom panel from power pack and set aside. RETAINING SCREW LOCATION HO0110 HO0111 SIDE VIEW 8. REMOVE THE KNOCK-OUT OPENING From inside the power pack, remove the wiring cover by removing two (2) retaining screws and set aside. Punch out the electrical knockout hole on top of the hood. Install the wire clamp (included in parts bag). HR0027 9.
10. CONNECT WIRING ! WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. Position the power pack below the installed custom hood. Insert the house wiring cable through the wire clamp previously installed in step 8. Tighten the wire clamp to secure the cable.
11. REMOVE THE BLOWER(S) (CONT’D) BLOWERS CP37 MODEL For each blower, using a 5/16” socket, remove all blower mounting screws from the inner top of the power pack front and rear brackets. Set aside the screws. BLOWERS HD0297 For each blower, slide it to disengage its flanges from the retaining brackets. Set aside the blowers. HD0298 12. INSTALL THE POWER PACK CAUTION Take care not to kink ducting when installing the power pack. Using provided no.
13. REINSTALL THE BLOWER(S) CP35 MODELS Slide the blower to engage its flange in the retaining bracket. HD0293 LEFT SIDE MOUNTING SCREW LOCATION Using a 5/16” socket, secure the blower to the inner top of the power pack with all blower mounting screws (previously removed in step 11). RIGHT SIDE MOUNTING SCREW LOCATION HD0282 HD0269 CP37 MODEL For each blower, slide it to engage its flanges in both retaining brackets. NOTE: Both blowers are identical and can be mounted on either side of the power pack.
14. REINSTALL BOTTOM PANEL Lift the bottom panel and engage the power pack metal tabs in bottom panel slots, as shown in details A and B below. Secure the bottom panel to the power pack using its screws previously removed in step 7. SIDE VIEW RETAINING SCREW LOCATION A B HO0110 HO0112 15. REINSTALL GREASE DRIP RAIL A A. Insert one end of grease rail in power pack side (1) while lifting the other end over the bottom panel edge (2). B 1 B.
16. REINSTALL BAFFLE FILTERS CAUTION Remove protective plastic film covering filters before installing them. NOTES : 1. On 42” width model only, reinstall both filter fillers previously removed in step 5. 2. Assemble the metal handles to the filters, using provided no. 8-32 x 1/4” screws, before installing them in the power pack. It is recommended to install side filters first and finish with center one(s). 1 1. Insert one end of the filter into the upper channel of the power pack. 2.
18. USE AND CARE Baffle Filters The baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates greater grease—like frying foods or wok cooking. Remove baffle filters by pushing them towards the back of hood and rotating filters downward. Baffle filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the power pack. Clean all-metal filters in the dishwasher using a non-phosphate detergent.
19. OPERATION Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.
20. WARRANTY WARRANTY ONE-YEAR LIMITED WARRANTY Broan-NuTone LLC (“Broan-NuTone”) warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
21.
22. SERVICE PARTS Best CP35 & CP37 Series 2 1 3 4 5 10 6 7 13 9 8 14 11 HL0110 KEY PART NO. NO.
