User Manual

ManualsBrandsBeStar ManualsHardwareFT-15T-5.5A1

SPECIFICATION

TOTAL PAGE

www.be-star.com RoHS

Customer

Product No.Customer P/N

Model Name

Issue Date

Issue No.

BS/TEY01. 397

12/02/16

FT-15T-5.5A1

Date

Page

16 Feb. 12

01 of 05

Checked by

Drawn by

Customer approved

Approved by

BESTAR ELECTRONICS INDUSTRY CO.,LTD

No.199 HuangHe West Road.New district,ChangZhou,JiangSu Province,P.R.China

Tel: +86 519 88222567 Fax: +86 519 88222551

E-mail:wu@be-star.com http://www.be-star.com

Approval：

1.Electrical characteristics

2.Dimension

3.Characteristics

4.Measuring Method

5.Reliability Test

6.History Change Record

FOR PIEZO ELECTRIC BUZZER

Summary of content (5 pages)

PAGE 1
SPECIFICATION FOR PIEZO ELECTRIC BUZZER www.be-star.com TOTAL PAGE 05 Customer Model Name Customer P/N Product No. Date 16 Feb. 12 Page 01 of 05 Issue No. Issue Date RoHS FT-15T-5.5A1 BS/TEY01. 397 12/02/16 Approval： 1.Electrical characteristics 2.Dimension 3.Characteristics 4.Measuring Method 5.Reliability Test 6.History Change Record Drawn by Checked by Approved by Customer approved BESTAR ELECTRONICS INDUSTRY CO.,LTD No.199 HuangHe West Road.New district,ChangZhou,JiangSu Province,P.R.
PAGE 2
6 H 5 4 2 3 1 FT-15T-5.5A1 H 1.Electrical characteristics G This print and information there in are proprietary to Bestar Electronics Industry Co., Ltd. and shall not be used in whole or in part without its written content F 1. Resonant Frequency 5.5±0.5 K Hz 2. Resonant Impedance 800 ohm max. 3. Capacitance at 120Hz 10±30% nF 4. Input Voltage 30 Vp-p 5. Operating Tmperature -20...+70°C 6. Storage Temperature -30...+80 °C 7. Metal Material G F Brass 2.
PAGE 3
6 H 5 4 2 3 1 FT-15T-5.5A1 H 3.Characteristics: 3.1 Solderability Solder AWG 30 wire with solder wire(Pb10Sn88Ag2) at 280±10°C on the ceramic , less than 2 seconds duration of soldering. 3.2 Lead pull off test G G a) Wire to be soldered on ceramic at the edge. It should withstand minimum 20N force applied in 180° .The wire should not come out before this .The ceramic can be either glued on a surface of can be held in hand.(Fig.3.
PAGE 4
6 H 5 4 2 3 1 FT-15T-5.5A1 H 5.Reliability Test: 5.1.High Temperature Test Temperture Duration 5.2.Low Temperature Test Temperature Duration 5.3.Temperature Cycle Test G +90°C 240hrs G -20°C 240hrs +90 C +20 C +20 C -20 C 30min 30min 15min all these tests above should be measured after leaving normal temperature for 2hrs. F This print and information there in are proprietary to Bestar Electronics Industry Co., Ltd.
PAGE 5
6 5 4 2 3 1 FT-15T-5.5A1 H H 6.History change record version No. G Change Items Before Date X1 This print and information there in are proprietary to Bestar Electronics Industry Co., Ltd. and shall not be used in whole or in part without its written content Drawn Approved After 12/02/16 G Li Hongyuan Ma Guoyang F F E E D D C C B B A Date Rev. Drawn Note Date: 12/02/16 Drawn by: Ma Guoyang Checked by: Zhao Zheng Approved by: Li Hongyuan www.be-star.com wu@be-star.