Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Installation Instructions Sunrider for Hardtop Installation Tips Before you begin installing your new Sunrider for Hardtop, please read all the instructions thoroughly, and watch the Bestop installation video. (See Support section on this page.) For a smooth fit: For easier installation, the top should be installed at a temperature above 72° F.
Installation Instructions Sunrider for Hardtop P2 - 52450 Rev. E 0416 Installation Instructions - Sunrider for Hardtop Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 © 2016 Bestop, Inc.
Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Installation Instructions Sunrider for Hardtop Parts List - Required parts for each installation section Sections 2, 3 & 4 Knob Qty. 4 Part # 478.90 Sections 3, 5 & 8 - Page number in Installation Guide Hardware & Door Rails Flanged Screw M6 x 20mm Qty. 6 Part # 514.48 Right Door Rail With Foam Seals Qty. 1 Part # 516.90 Left Door Rail With Foam Seals Qty. 1 Part # 516.
Section 1 Remove Hardtop Freedom Panels & Clean Windshield and Hardtop Seals Page 4 Step 1 Vehicle-Equipped Mushroom Knob Qty. 2 Clean seals along top of windshield and around edge of hardtop Save the large Mushroom Knobs for re-use when installing the Sunrider for Hardtop. Step 1 Remove both hardtop freedom panels, according to instructions in your owner’s manual. Save the large Mushroom Knobs for re-use when installing the Sunrider for Hardtop.
Section 2 Page 5 Install Door Rails Step 1 516.91 516.90 478.90 Hardware Knob Part # 478.90 Qty. 1 per side Right Door Rail With Foam Seals Qty. 1 Part # 516.90 Left Side Utility Knife Step 1 Left Door Rail With Foam Seals Qty. 1 Part # 516.91 4-Door Vehicles: Make two incisions in the sport bar padding on each side of the vehicle before installing rear knobs. Install the Left Door Rail #516.91 on the vehicle using one of the supplied Knobs #478.90. Only install the front knob at this step.
Section 3 Page 6 Install Deck Assembly Step 1 516.23 478.90 Hardware Top Deck Assembly Qty. 1 Part # 516.23 Knob Part # 478.90 Qty. 1 per side Align and Press Up Here NOTICE It will be helpful to have two (2) people available for this step and a small step stool or ladder to reduce the difficulty installing the Top Deck Assembly. Be sure to inspect and align the pieces and press up from below when installing the knobs. Step 1 Install the deck assembly on the vehicle.
Section 4 Page 7 Install Vehicle-Equipped Mushroom Knobs; Install Flanged Screws Step 1 Hardware Vehicle-Equipped Mushroom Knob Qty. 2 Step 2 514.48 Flanged Screw M6 x 20mm Part # 514.48 Qty. 2 4mm Allen Wrench Step 1 Step 2 Install the vehicle-equipped mushroom knobs originally supplied with the vehicle hardtop panels, and removed in Section 1, up through the bottom of the sound bar in the locations shown. Using the 4mm Allen wrench, install a M6 x 20mm Flanged Screw #514.
Section 5 Page 8 Install Rear Attach Brackets Step 1 517.10 514.48 Hardware Rear Attach Bracket Qty. 2 Part # 517.10 Rear Attach Bracket locations Flanged Screw M6 x 20mm Part # 514.48 Qty. 2 per bracket 4mm Allen Wrench Step 1 Using the 4mm Allen wrench, install the Rear Attach Brackets #517.10 with two (2) M6 x 20mm Flanged Screws per bracket.
Section 6 Page 9 Tighten All Knobs Step 1 Step 2 6 knob locations 6 knob locations Step 2 Step 1 Fold down the Sunrider for Hardtop by pulling the header toward the front of the vehicle, and down into the closed position. Tighten all six of the knobs at this time - the four #478.90 knobs, and the two vehicle-equipped mushroom knobs. P9 - 52450 Rev. E 0416 Installation Instructions - Sunrider for Hardtop © 2016 Bestop, Inc.
Section 7 Page 10 Close the Windshield Header Latches Step 2 Step 1 1 2 Step 1 Step 2 From inside the Jeep, locate the two Windshield Header Latches. To close the latch, pivot the latch handle to the completely open position to allow the hook to engage the windshield loop. Now pivot the hook forward to engage the windshield loop. When the hook is engaged with the windshield loop, close the latch by pivoting it forward toward the windshield. Repeat on both sides of the vehicle.
Section 8 Page 11 Check the Seal for Fit Step 1 NOTICE Check the seal position and adjust as required to be sure it fits and covers the channel between the rear hardtop and the Sunrider for Hardtop for maximum water leak protection. Jeep hardtop seals vary by model year. Some seals contain stuffers in the center section that may cause the Sunrider for Hardtop rear seal to stick out in the center.
Section 9 Page 12 Open and Secure Sunrider (optional) Step 1 Hardware Step 2 410.42 1 2 Sunrider Tie-Down Straps Qty. 2 Part # 410.42 Wrap strap twice around NOTICE This step is OPTIONAL and only recommended when driving off-road or in a situation where the Top Deck Assembly could shift. Step 1 Secure the Sunrider with the Tie Down Straps, #410.12. Wrap each strap around the arm twice and secure the hook-and-loop strap. From inside the Jeep, locate the two Windshield Header Latches.
Installation Instructions Sunrider for Hardtop - Vinyl Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Care and Maintenance of your Bestop Product Your Bestop product is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush Rinse with clear water to remove all traces of soap.
Installation Instructions Sunrider for Hardtop - Vinyl Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Soin et entretien de votre produit Bestop Votre produit Bestop est fabriqué des meilleurs matériaux disponibles. Il devra être nettoyé et entretenu régulièrement afin de maintenir son apparence neuve et pour une durée d’utilisation maximale. Tissu: Le tissu doit être lavé régulièrement à l’aide de savon, d’eau chaude et d’une brosse à soies douces.
Installation Instructions Sunrider for Hardtop - Vinyl Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Cuidado y mantenimiento de su producto Bestop Su producto Bestop está hecho con materiales de la más alta calidad. Para mantener su apariencia nueva y alargar su uso al máximo posible, necesitará limpieza y mantenimiento periódicos. Tela: debe lavar la tela con frecuencia usando jabón, agua tibia y un cepillo de cerdas suaves.
Installation Instructions Sunrider for Hardtop - Twill Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Care and Maintenance of your Bestop Product Your Bestop product is made of the finest materials available. To keep it looking new and for the maximum possible life, it will need periodic cleaning and maintenance. Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush. Rinse with clear water to remove all traces of soap.
Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Installation Instructions Sunrider for Hardtop - Twill Soin et entretien de votre produit Bestop Votre produit Bestop est fabriqué des meilleurs matériaux disponibles. Il devra être nettoyé et entretenu régulièrement afin de maintenir son apparence neuve et pour une durée d’utilisation maximale. Tissu : Le tissu doit être lavé régulièrement à l’aide de savon, d’eau chaude et d’une brosse à soies douces.
Vehicle Application: Jeep Wrangler / Wrangler Unlimited 2007-current Part Number 52450 Installation Instructions Sunrider for Hardtop - Twill Cuidado y mantenimiento de su producto Bestop Su producto Bestop está hecho con materiales de la más alta calidad. Para mantener su aspecto nuevo y alargar su vida útil al máximo posible, necesitará limpieza y mantenimiento periódicos. Tela: debe lavar la tela con frecuencia usando jabón, agua tibia y un cepillo de cerdas suaves.