Installation Instructions Supertop for Truck Vehicle Application: • Ford F-150 Regular / Super Cab 2004 and newer (6.5 ft.) Part Number: 76305 • Nissan Titan King Cab without Utili-Track 2004 and newer (6.5 ft.) Part Number: 76305 www.bestop.com - We’re here to help! Visit our web site and click on “Ask a Question”. Click here for more Truck Accessories by Bestop.
Supertop for Truck Installation Instructions Supertop Fabric Side Panel, Right Side Panel, Left Rear Window 32" Buckle Straps Elastic Garter Self-Adhesive Hook Strip, 66" Foam Tape, 14' Qty - 1 Qty - 1 Qty - 1 Qty - 1 Qty - 2 Qty - 2 Qty - 1 Qty - 1 Parts List and Hardware Identification Tailgate Bracket, Left, Part Number 412.09, Qty - 1 Tailgate Bracket, Right, Part Number 412.08, Qty - 1 1/4" Fender Washer, Part Number 410.94, Qty - 4 Front Belt Rail, Right, Part Number 412.
Supertop for Truck Installation Instructions Mount Tailgate Brackets to Rear Belt Rails Locate the Right Tailgate Bracket and the Right Rear Belt Rail in the parts kit. Place the Right Tailgate Bracket over the rear stud on the Belt Rail so that the bracket tab points away from the channel on the Belt Rail. Use a 1/4-20 Cap Nut to secure the bracket to the rail. Repeat with the Left Tailgate Bracket and Rear Belt Rail.
Supertop for Truck Installation Instructions Assemble Front Bow Install Belt Rail Assemblies Slide a Bow Tie Down Strap onto each of the Front Bow Halves. Slide the two halves of the bow into a Bow Coupler. Lay the Belt Rail Assemblies on top of the truck bed rail with the tab on the Tailgate Bracket toward the center of the vehicle. The front of the rail should be flush with the inside edge of the front wall of the truck box.
Supertop for Truck Installation Instructions Install Rear Bow Assembly Locate the two (2) Elastic Garters in the parts kit. Slide a garter over each half of the Rear Bow from the center so that the Garters will hang above the rear window opening. Slide the two (2) halves of the Rear Bow into the remaining Bow Couplers. Slide the legs of the Rear Bow Assembly over the 5/16" x 3/4" Clevis Pins and secure them with a 5/16" Flat Washer and a Hitch Pin Clip on each side of the vehicle.
Supertop for Truck Installation Instructions Snap Fabric to Rear and Center Bows Thread Buckles on Straps Thread the end of the 32" Buckle Straps through the male half of each buckle. Carefully drape the fabric over the center and rear bows. Make sure that the sides of the top are smooth between the bows. Locate the two rear snap flaps. Wrap them around under the bow from the rear and snap them to the bow. Then locate the six (6) snap tabs sewn to the inside of the top in the center.
Supertop for Truck Installation Instructions Secure the Front of the Top Secure the Front of the Top Start at the front corners of the top and work the plastic strip sewn into the bottom of the panels into the channel in the Side Belt Rail. Make sure that the fabric loop sewn to the top is outside the vehicle. Locate the loop strip sewn to the flap along the front of the top. Fasten it to the Adhesive Hook Strip installed along the front of the bed.
Supertop for Truck Installation Instructions We recommend that the Third Brake Light supplied with this assembly Secure the Rear of the Top Locate the plastic clips sewn into the rear corners of the top. Gently pull down on the rear bow and pull down and back on the fabric to hook the clips into the corner of the Tailgate Bracket on the Belt Rail Assembly. Locate the plastic strip next to the clip and hook it into the channel on the Side Belt Rail.
Supertop for Truck Installation Instructions Engage J-Hook on Rear Window Install Tailgate Bar on Rear Window Slide the Tailgate Bar onto the tube strip sewn to the inside of the Rear Window. Place the Tailgate Bar in the Tailgate Brackets on the Belt Rail Assemblies. Close the zippers on each side of the window. Close the flaps on each side of the window over the zippers and fasten the hook and loop. Check that the tailgate closes on the Bulb Seal.
Supertop for Truck Installation Instructions Install Side Panels Adjust Tension on Top Orient the Side Panels with the plastic J-Hook toward the top and the zipper with the flap over it toward the rear and determine which is for the driver’s side of the vehicle and which is for the passenger side. Align the J-Hook on the top of the panel with the J-Hook sewn into the top above the panel opening. Slide them together.
Supertop for Truck Installation Instructions Collapsing the Pickup Top Release the Rear and Center Bows Remove Windows Rotate the Rear Bow forward to collapse the Rear and Center Bows onto the Front Bow. As you are collapsing the bow assembly, make sure that the J-Hook above the side opening is folded inside the vehicle. Fold all the J-Hook and fabric in toward the center along the front of the bed on each side. Remove the Side Panels and the Rear Window and store them carefully.
Supertop for Truck Installation Instructions Secure Fabric with Buckle Straps To Remove the Bow Stack If you wish to remove the bows completely, remove the cotter pins that secure the bows to the Bow Mount Brackets. Lift the bows off the vehicle, keeping the bows together. Carefully store the bows and fabric. Replace the Cotter Pins in the Bow Mount Brackets on the vehicle. Wrap the Buckle Straps around the fabric and the J-Hook and secure the buckles.
Supertop for Truck Installation Instructions Care and Maintenance of your Bestop Top Your top is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Washing: The fabric should be washed often using soap, warm water and a soft bristle brush. Rinse with clear water to remove all traces of soap. Windows: Keep windows clean to avoid scratching.