Installation Manual

ManualsBrandsBestop ManualsAutomotiveBestop 90024-35 Black Diamond Duster Deck Cover for 2004-2006 Wrangler Unlimited with Factory Hardtop Removed

90022 pg 1

1004 Rev. A

Duster Deck Cover

Installation Instructions Part Number: 90024

WARNING

For: Jeep

Wrangler TJ Unlimited 2004-Current

with Factory Hard Top

This product is designed to enhance the appearance of the

vehicle. Do not rely in any way on the components of this

product to contain occupants or cargo within the vehicle, or

to protect against injury or death in the event of an accident.

Never operate vehicle in excess of manufacturer’s specifi-

cations.

WEAR SEAT BELTS AT ALL TIMES

Read and follow, precisely, all installation instructions pro-

vided when installing this product. Failure to do so could

place occupants or cargo of the vehicle in a potentially

dangerous situation. After installing or reinstalling, check to

make sure it has been properly installed.

Installation Tips

Before you begin installing this product, read all instructions

thoroughly. Below are a few tips to make this installation

easier. After completing the installation, keep these instructions

for further reference.

For a smooth fit:

For ease in installation, the Duster should be installed at

temperatures above 72° F. Below this temperature, the fabric

may contract an inch or more, making it difficult to fit to the

vehicle.

It is normal for the fabric to contract and wrinkle when stored in

the shipping carton. Within a few days after the installation, the

fabric will relax and the wrinkles will disappear.

DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE.

This product is only designed for the vehicles listed above. Failure to install this product on the proper

vehicle could cause injury to the vehicle occupants and damage to the product.

Summary of content (6 pages)

PAGE 1
Duster Deck Cover Installation Instructions Part Number: 90024 For: Jeep® Wrangler TJ Unlimited 2004-Current with Factory Hard Top DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE. This product is only designed for the vehicles listed above. Failure to install this product on the proper vehicle could cause injury to the vehicle occupants and damage to the product. WARNING This product is designed to enhance the appearance of the vehicle.
PAGE 2
Parts List and Hardware Identification Duster Qty - 1 #8 x 1/2" Pan Head Washer Screw Black, Qty - 4, Part Number 200.48 Tailgate Bar, Qty - 1, Part Number 288.75 Tools Needed #2 Phillips Screwdriver Center Punch* Power Drill* Safety Glasses 1/8" Drill Bit* * on some models Web Buckle Strap, Qty - 1, Part Number 312.01 Installation Tailgate Retainer Mount, Left, Qty - 1, Part Number 311.85 Tailgate Retainer Mount, Right, Qty - 1, Part Number 311.
PAGE 3
Note : This product is designed for a "Custom Fit". Be patient during the installation, it fits tight! Step Two SECURE REAR SEAT Locate the Web Buckle Strap in the parts kit. Thread the web end of the strap through the footman loop closest to the rear of the seat on the Driver’s side. Fold the back of the seat down and thread the web through the bar on the seat back. Thread the end of the strap through the buckle and pull it tight.
PAGE 4
Step Five SECURE PLASTIC STRIPS Locate the plastic strip sewn to the Duster along each side of the vehicle. Start at one end on each side and roll the plastic strip into the Side Retainers. Slide strips as far forward of the vehicle. Side Retainer Fabric Plastic Strip Roll Plastic Strip into Side Retainer Plastic Strip Detail of Plastic Strip Step Seven Step Six SECURE COLLARS SECURE REAR CORNERS Roll the plastic strips, sewn into the rear corners of the Duster into the Corner Retainers.
PAGE 5
If You Have a New Windjammer on Your Vehicle To Remove Duster Optional Installation When removing the Duster, use the loops sewn to the fabric to release the plastic strips. Pull gently down, then straight out to release the plastic strip from the retainers. Step One - Optional Locate Attaching Snaps from Hardware Kit supplied with the Windjammer.
PAGE 6
Care and Maintenance of your New Duster Your Duster is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Washing: The fabric should be washed often using soap, warm water and a soft bristle brush. Rinse with clear water to remove all traces of soap. Water: Seeping through at the seams may be stopped by applying 3-M Scotchgard® on the inside of the seams.