CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Dresser Model 419517 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification D I F A C H N D212 D166 I D975 B E D213 O M65 J H P P D50 D167 D212 D166 D975 D975 D51 D213 M65 K D50 D167 M65 L D975 D51 M65 M www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the ENDS (A and B) and UPRIGHT (C). å Repeat this step for the BOTTOM (E). Do not tighten the TWIST-LOCK® FASTENERS in this step. 7F (10 used) C B A www.sauder.
Step 2 å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B) and DRAWER BRACES (M65). Just think. The sooner you do this, the sooner you do something else. Arrow 1F A ith ® e w LOCK S c a f Sur WIST TENER T AS F B ith ® e w LOCK S c a f Sur WIST TENER T AS F Arrow M65 1F M65 M65 M65 M65 M65 Arrow Arrow 1F (12 used) Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 419517 www.sauder.
Step 3 å Turn twelve CAM SCREWS (8F) into the FRONT LEGS (H) and DRAWER FRONTS (J, K, L, and M). 8F (12 used) M M H K H www.sauder.
Step 4 å å å å Insert a WOOD DOWEL (15F) into the indicated holes in the FRONT LEG (H). Fasten the RIGHT END (A) to the FRONT LEG (H). Tighten three HIDDEN CAMS. NOTE: Be sure the WOOD DOWEL in the LEG inserts into the RIGHT END. Fasten a BACK LEG (I) to the RIGHT END (A) as shown in the lower diagram. Use three BLACK 2-1/4" FLAT HEAD SCREWS (26S). 1 A ith e w K® c a C f Sur T-LO S S I TW TENER FAS 2 The LEG will overhang this edge. These surfaces should be even.
Step 5 å å å å Insert the WOOD DOWEL (15F) into the indicated hole in the FRONT LEG (H). Fasten the LEFT END (B) to the FRONT LEG (H). Tighten three HIDDEN CAMS. NOTE: Be sure the WOOD DOWEL in the LEG inserts into the LEFT END. Fasten the BACK LEG (I) to the LEFT END (B) as shown in the lower diagram. Use three BLACK 2-1/4" FLAT HEAD SCREWS (26S). Sur f TW ace wi IS th FAS T-LO TEN CK® ERS B These surfaces should be even. The LEG will overhang this edge.
Step 6 VIEW THE DRAWER GLIDE VIDEO å Fasten six UNIVERSAL CABINET RAILS* (40DA) to the ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end 1 2 3 4 1 2 4 4 3 1 3 2 A 2 4 1 3 2 4 1 4 3 ith ® e w LOCK S c a f Sur WIST TENER T AS F 3 2 B 1 with CK® e c fa -LO S Sur WIST TENER T AS F Glide end Page 10 419517 www.sauder.
Step 7 VIEW THE DRAWER GLIDE VIDEO å Fasten six UNIVERSAL CABINET RAILS* (40DA) to the UPRIGHT (C). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) 4 3 2 4 1 3 C 2 with CK® e c fa -LO S Sur WIST TENER T AS F 1 Finished edge 4 3 2 1 2 1 2 Glide end 4 3 1 2 1 www.sauder.
Step 8 å Fasten the LEFT END (B) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge H B ith e w K® c a C f Sur T-LO S S I TW TENER FAS D Sur fac ew ith hol es Dowel end How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
Step 9 å Fasten the UPRIGHT (C) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. Don't worry. It isn't Rome. This can be built in a day. D Finished edge C www.sauder.
Step 10 å Fasten the BOTTOM (E) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Slide the BOTTOM MOLDING* (O) onto the notched edge of the BOTTOM (E). å *U.S. Patent No. 5,499,886 Notched edge B C E Sur f TW ace wi IS th FAS T-LO TEN CK® ERS O 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) The groove is closer to this edge. Page 14 419517 www.sauder.
Step 11 å Fasten the RIGHT END (A) to the TOP (D) and BOTTOM (E). Tighten four TWIST-LOCK® FASTENERS. å Fasten the METAL BRACKETS (4G) to the ENDS (A and B) and UPRIGHT (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the FRONT MOLDING (N) to the ENDS (A and B) and UPRIGHT (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS and into the MOLDING. 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) N 4G B 4G D C H E www.sauder.
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å First, make equal margins along the top and bottom edges of the BACK (F). Then, make equal margins along the side edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). å Peel the FELT DISC from the FELT DISC CARD (1M). Stick the FELT DISC on the LEGS (H and I).
Step 13 å Fasten the FOOT BRACKET (6E) to the BOTTOM (E). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å å å Slide the FEET (P) onto the FOOT BRACKET (6E). Slide the CORNER CAP (5E) onto the FEET (P). Turn two BLACK 9/16" LARGE HEAD SCREWS (1S) into the short slots of the FOOT BRACKET (6E). 1S BLACK 9/16" LARGE HEAD SCREW (5 used in this step) E 1S P 6E 6E P Completed foot support 5E www.sauder.
Step 14 VIEW THE T-SLOT BOX VIDEO Push down 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 9G L D51 D975 D50 Unfi nish ed sur fac e D50 1S BLACK 9/16" LARGE HEAD SCREW (16 used in this step) å Pull the DRAWER FRONT BRACKETS (9G) apart and slide them into the grooves in the DRAWER SIDES (D50 and D51). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification.
Step 15 VIEW THE T-SLOT BOX VIDEO Push down 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 8G J D213 D975 D212 1S D212 Unfi nish ed sur fac e BLACK 9/16" LARGE HEAD SCREW (8 used in this step) å Pull the DRAWER FRONT BRACKETS (8G) apart and slide them into the grooves in the DRAWER SIDES (D212 and D213). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification.
Step 16 VIEW THE DRAWER GLIDE VIDEO å Fasten a DRAWER RIGHT (40DC) to the LOWER RIGHT DRAWER SIDE (D50) and a DRAWER LEFT (40DD) to the LOWER LEFT DRAWER SIDE (D51). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å NOTE: The glides are not intended to rotate. å Repeat this step for the other drawers. If you're doing this to help a friend, don't leave without a bite. Fasten a PULL (98K) to the LOWER RIGHT DRAWER FRONT (L).
Step 17 å å Carefully stand your unit upright in its final location against a wall. We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 2-1/4" FLAT HEAD SCREW (26S) into a stud in your wall. BLACK 2-1/4" FLAT HEAD SCREW (1 used in this step) 26S 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S www.sauder.
Step 18 å To insert the drawers into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. å å NOTE: Be sure the label on the LEFT DRAWER SIDE is in one of the UPPER drawers. å å NOTE: Please read the back pages of the instruction booklet for important safety information.
Modèle 419517 Commode Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer six GLISSIÈRES D'ÉLÉMENT UNIVERSELLES* (40DA) au MONTANT (C). Utiliser douze VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 4. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) dans les gros trous des EXTRÉMITÉS (A et B) et le MONTANT (C).
ÉTAPE 12 ÉTAPE 15 (SUITE) Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (F) et le placer sur l'élément. Tout d’abord, veiller à avoir des marges égales le long des chants supérieur et inférieur de l'ARRIÈRE (F). Ensuite, veiller à avoir des marges égales le long des chants latéraux de l'ARRIÈRE (F).
Cómoda Modelo 419517 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije seis RIELES UNIVERSALES DE GABINETE* (40DA) al PARAL (C). Utilice doce TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 4. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) en los agujeros grandes de los EXTREMOS (A y B) y del PARAL (C).
PASO 12 PASO 15 (CONTINUACIÓN) Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (F) y colóquelo sobre la unidad. Primero, el margen a lo largo de los bordes superior e inferior del DORSO (F) debe estar uniforme. A continuación, los márgenes a lo largo de los dos bordes del DORSO (F) deben estar uniformes.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.