CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) Stuff a sock in it. Or two. 4-Drawer Chest NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Model 420566 PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification C2 I F A G L E I D2 B D2 H D10 D174 D983 L M65 D11 J D132 D175 D983 D138 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the ENDS (A and B) and BOTTOMS (D2). Some assembly (and snacks) required. Do not tighten the TWIST-LOCK® FASTENERS in this step. 7F D2 D2 A 7F B www.sauder.
Step 2 å Push ten HIDDEN CAMS (1F) into the ENDS (A and B) and DRAWER BRACES (M65). Arrow 1F A B Arrow M65 1F M65 (10 used) M65 M65 Arrow Arrow 1F Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 420566 www.sauder.
Step 3 å Turn ten CAM SCREWS (8F) into the FRONT LEGS (G and H) and DRAWER FRONTS (J and K). (10 used) 8F H G K K K J www.sauder.
Step 4 å Fasten the ENDS (A and B) to the FRONT LEGS (G and H). Tighten six HIDDEN CAMS. 1 The FRONT LEG will overhang this edge. 2 A Sur HIDface w DEN ith CA MS RIGHT END ASSEMBLY Edge with TWIST-LOCK® FASTENERS G These surfaces should be even. Edge with TWIST-LOCK® FASTENERS B Sur HIDface w DEN ith CA MS LEFT END ASSEMBLY H The FRONT LEG will overhang this edge. These surfaces should be even. Page 8 420566 www.sauder.
Step 5 å å Lay the ENDS (A and B) flat on the floor exactly as shown. å å NOTE: Do not overtighten the SCREWS. å NOTE: If the MOLDING comes up off of the SCREWS, remove it and slide it on again. Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. Slide the END MOLDINGS (L) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS.
Step 6 å Stand the ENDS (A and B) upright as shown and fasten the REAR LEGS (I) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) RIGHT END ASSEMBLY I These surfaces should be even. The BACK LEG will overhang this edge. A Sur HIDface w DEN ith CA MS LEFT END ASSEMBLY Edge with TWIST-LOCK® FASTENERS 26S These surfaces should be even.
Step 7 VIEW THE DRAWER GLIDE VIDEO å Fasten the UNIVERSAL CABINET RAILS* (40DA) to the ENDS (A and B). Use sixteen GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (16 used in this step) 1 Glide end 2 1 3 4 2 1 3 4 3 4 2 A 2 3 4 3 4 2 3 1 ith ® e w LOCK S c a f Sur WIST TENER T AS F 4 2 3 1 G 4 2 B 1 www.sauder.
Step 8 å Fasten the LEFT END (B) to the TOP (C2). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 9 å å å Fasten four METAL BRACKETS (2G) to the BACK (E). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the METAL BRACKETS are even with the edges of the BACK. Fasten the BACK (E) to the LEFT END (B). Use two BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the BACK and into the LEFT END. 2G 1S E S few urfac er h e w ole ith s BLACK 9/16" LARGE HEAD SCREW (6 used in this step) 2G B The six holes on the other surface should be located closer to this edge.
Step 10 å Insert two METAL PINS (1R) into the holes in the LEFT END (B). å Fasten the BOTTOMS (D2) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. å NOTE: Be sure the METAL PINS in the LEFT END insert into the holes in the BOTTOMS. Don't worry. It isn't Rome. This can be built in a day. Finished edge B 1R D2 D2 Sur TWface w FASIST-LOithout TEN CK ERS ® Sur TWface w FASIST-LOithout TEN CK ERS ® Finished edge Page 14 420566 www.sauder.
Step 11 å å å å Insert two METAL PINS (1R) into the holes in the RIGHT END (A). Fasten the RIGHT END (A) to the TOP (C2) and BOTTOMS (D2). Tighten four TWIST-LOCK® FASTENERS. NOTE: Be sure the METAL PINS in the RIGHT END insert into the holes in the BOTTOMS. Fasten the RIGHT END (A) to the BACK (E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the BACK and into the RIGHT END.
Step 12 å Carefully turn your unit over onto its front edges. Lay the LARGE BACK (F) over your unit. å Turn six BLACK 9/16" LARGE HEAD SCREWS (1S) into the bottom edge of the LARGE BACK (F) and into the BACK (E). Do not completely tighten the SCREWS at this time. å Then, making sure that the top edge of the LARGE BACK (F) sits slightly below the top edge of your unit, fasten the top and side edges of the LARGE BACK to your unit using the NAILS (1N).
Step 13 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Unfi sur nished fac e D132 D983 D132 K D138 D138 K Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the LARGE DRAWER SIDES (D132 and D138) at an angle into the slot at each end of the LARGE DRAWER FRONT (K).
Step 14 VIEW THE DRAWER GLIDE VIDEO å å Insert a SLIDE CAM (10A) into the LARGE DRAWER SIDES (D132 and D138). å å å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten a DRAWER RIGHT (40DC) to the LARGE RIGHT DRAWER SIDE (D132) and a DRAWER LEFT (40DD) to the LARGE LEFT DRAWER SIDE (D138). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. NOTE: The glides are not intended to rotate. Repeat this step for the other drawers.
Step 15 å Fasten three KNOBS (5K) to the DRAWER FRONT (J). Use three BLACK 1-1/8" MACHINE SCREWS (21S). å Fasten two PULLS (74K) to the LARGE DRAWER FRONT (K). Use four SILVER 3/4" MACHINE SCREWS (20S). å Repeat this step for the other large drawers. 21S BLACK 1-1/8" MACHINE SCREW (3 used for the KNOBS) J 5K 20S SILVER 3/4" MACHINE SCREW (12 used for the PULLS) K 74K www.sauder.
Step 16 å å å Carefully stand your unit upright in its final location. We recommend using the SAFETY STRAP for added stability. å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and one end of the SAFETY STRAP. 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4.
Step 17 å WARNING To insert the drawers into your unit, tip the front of the drawers down and drop the glides on the drawers behind the glides on the unit. Lift the front of the drawers up and slide them into the unit Children have died from furniture tipover. To reduce the risk of furniture tipover: • ALWAYS install tipover restraint provided. • NEVER put a TV on this product. • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves. • NEVER open more than one drawer at a time.
Step 18 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 420566 Commode 4 Tiroirs Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 8 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) dans les gros trous des EXTRÉMITÉS (A et B) et les DESSOUS (D2). Enfoncer dix EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B) et les ENTRETOISES DE TIROIR (M65).
ÉTAPE 12 (SUITE) ÉTAPE 16 (SUITE) Ensuite, s'assurer que le chant supérieur de le GRAND ARRIÈRE (F) repose légèrement au-dessous e chant supérieur de l'élément, fixer les chants supérieur et latéraux du GRAND ARRIÈRE à l'élément à l'aide des CLOUS (1N). Maintenant, serrer complètement les VIS dans le chant inférieur du GRAND ARRIÈRE (F). REMARQUE : Des perforations ont été prévues pour accès à travers le GRAND ARRIÈRE.
Modelo 420566 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 8 No apriete los SUJETADORES TWIST-LOCK® en este paso. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes de los EXTREMOS (A y B) de los FONDOS (D2). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije el EXTREMO IZQUIERDO (B) al PANEL SUPERIOR (C2).
PASO 12 (CONTINUACIÓN) PASO 16 (CONTINUACIÓN) A continuación, asegúrese de que del borde superior del DORSO GRANDE (F) se asienta ligeramente por debajo del borde superior de la unidad, fije los bordes superior y laterales del DORSO GRANDE a la unidad utilizando los CLAVOS (1N). Ahora, apriete los TORNILLOS por completo en el borde inferior del DORSO GRANDE (F). NOTA: Se ha provisto una perforación para acceso a través del DORSO GRANDE.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
