CONTACT US FIRST BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-19 Français 20-22 Español 23-25 Safety 26 Warranty 27 Hammer Not actual size Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification C2 H E A P F H D B G O P D24 D109 D716 D25 I www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eight HIDDEN CAMS (1F) into the ENDS (A and B) and BOTTOM (D). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. å NOTE: Use the exact holes shown. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Push four HIDDEN CAMS (1F) into the ENDS (A and B). Just think. The sooner you do this, the sooner you do something else. Arrow 1F B A Arrow 1F Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 420567 www.sauder.
Step 3 å Turn four CAM SCREWS (8F) into the FRONT LEGS (F and G). 8F (4 used) F G www.sauder.
Step 4 å Fasten the ENDS (A and B) to the FRONT LEGS (F and G). Tighten four HIDDEN CAMS. 1 2 Edge with CAM DOWELS B Sur fac ew ith HID DEN CA MS These surfaces should be even. A Sur fac ew ith HID DEN CA MS G Angled edge Edge with CAM DOWELS Angled edge F These surfaces should be even. Page 8 420567 www.sauder.
Step 5 å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å å NOTE: Do not overtighten the SCREWS. BLACK 9/16" FLAT HEAD SCREW (4 used in this step) NOTE: If the MOLDING comes up off of the SCREWS, remove it and slide it on again. S HI urfa DD ce EN wi CA tho M ut S å 32S Slide the END MOLDINGS (P) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS.
Step 6 å Fasten the REAR LEGS (H) to the ENDS (A and B). Use four BLACK 2-1/4" FLAT HEAD SCREWS (26S). 26S BLACK 2-1/4" FLAT HEAD SCREW (4 used in this step) H These surfaces should be even. Edge with CAM DOWELS B Sur fac ew ith HID DEN CA MS Angled edge Angled edge H These surfaces should be even. A Sur fac ew ith HID DEN CA MS Page 10 Edge with CAM DOWELS 420567 www.sauder.
Step 7 VIEW THE DRAWER GLIDE VIDEO å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system Don't worry. It isn't Rome. This can be built in a day. 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Glide end 1 2 3 A 3 2 H 1 Glide end H B www.sauder.
Step 8 å Fasten the LEFT END (B) to the TOP (C2). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Glide end C2 Sur fac ew ith hol es B withMS e c fa A Sur DEN C HID These edges should be even. Meet Part (C2). This component has been engineered to be lighter, stronger, faster… well ok. Not technically faster. But definitely makes for a sturdier night stand that’s easier to assemble and friendlier to the environment.
Step 9 å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two HIDDEN CAMS. å Slide the BOTTOM MOLDING* (O) onto the notched edge of the BOTTOM (D). å *U.S. Patent No. 5,499,886 Maximum 210 degrees Arrow Minimum 190 degrees Notched edge B O D Sur HIDface w DEN ith CA MS The large groove is closer to this edge. www.sauder.
Step 10 å Fasten the RIGHT END (A) to the TOP (C2) and BOTTOM (D). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees C2 D A ut itho S w e fac AM Sur DEN C HID Page 14 420567 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Lay the BACK (E) over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (E) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. With a hammer, gently tap four TACK GLIDES (12E) into the LEGS (F, G, and H).
Step 12 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Unfi nish ed sur fac e D24 D716 D25 I I Groove Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D24 and D25) at an angle into the slot at each end of the DRAWER FRONT (I).
Step 13 VIEW THE DRAWER GLIDE VIDEO å å Insert a SLIDE CAM (10A) into each DRAWER SIDE (D24 and D25). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å NOTE: The glides are not intended to rotate. If you're doing this to help a friend, don't leave without a bite. Fasten the DRAWER RIGHT (35AC) to the RIGHT DRAWER SIDE (D24) and the DRAWER LEFT (35AD) to the LEFT DRAWER SIDE (D25). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2.
Step 14 å å Carefully stand your unit upright. å Fasten the KNOB (186K) to the DRAWER FRONT (I). Use a BLACK 1-1/8" MACHINE SCREW (21S). To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. 21S BLACK 1-1/8" MACHINE SCREW (1 used in this step) 30 lbs. 15 lbs. I 186K 25 lbs. Page 18 420567 www.sauder.
Step 15 å To make adjustments to the drawer, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 420567 Chevet Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer les PIEDS ARRIÈRE (H) aux EXTRÉMITÉS (A et B). Utiliser quatre VIS TÊTE PLATE 57 mm NOIRES (26S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer huit EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B) et le DESSOUS (D). Ensuite, insérer l'extrémité en métal de la CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
ÉTAPE 10 ÉTAPE 13 Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (C2) et au DESSOUS (D). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Insérer une EXCENTRIQUE DE COULISSE (10A) dans chaque CÔTÉ DE TIROIR (D24 et D25). ÉTAPE 11 Fixer un TIROIR DROIT (35AC) sur le CÔTÉ DROIT DE TIROIR (D24) et un TIROIR GAUCHE (35AD) sur le CÔTÉ GAUCHE DE TIROIR (D25). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 2.
Modelo 420567 Mesa de noche Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije las PATAS POSTERIORES (H) a los EXTREMOS (A y B). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 57 mm (26S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje ocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B) y del FONDO (D). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 10 PASO 13 Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR (C2) y al FONDO (D). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Inserte un EXCÉNTRICO DE CORREDERA (10A) dentro cada LADO DE CAJÓN (D24 y D25). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije un CAJÓN DERECHO (35AC) al LADO DERECHO DE CAJÓN (D24) y un CAJÓN IZQUIERDO (35AD) al LADO IZQUIERDO DE CAJÓN (D25).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
