sauder.com How else are you gonna know which end is up? Twin Bookcase Headboard Model 420569 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-20 Français pg 21-23 Español pg 24-26 Lot # 545018 03/31/20 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 Assembly Steps 6-20 Français 21-23 Short Screwdriver Hammer Español Warranty Page 2 Not actual size 24-26 27 Electric drill with 1/4" bit (ONLY in indicated step) 420569 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) E TOP (1) I BACK (1) B LEFT END (1) F PANEL (1) J FLIP-UP DOOR (1) C RIGHT UPRIGHT (1) G SHELF (1) K ADJUSTABLE SHELF (2) D LEFT UPRIGHT (1) H SMALL SHELF (1) E I D C K H K B J G A F www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 12E TACK GLIDE - 4 7F TWIST-LOCK® FASTENER - 4 13H HINGE - 2 24M NUT - 4 1R METAL PIN - 12 Page 4 1F 2F HIDDEN CAM - 14 16G HEADBOARD BRACKET - 2 5G ANGLE BRACKET - 3 22H HINGE SPACER - 2 1N 2R 186K KNOB - 1 420569 13M WASHER - 4 12P CAM COVER - 6 NAIL - 30 RUBBER SLEEVE - 8 CAM DOWEL - 14 5R DOOR STOP - 1 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1S 21S BLACK 1-1/8" MACHINE SCREW - 1 BLACK 9/16" LARGE HEAD SCREW - 14 23S SILVER 5/8" FLAT HEAD SCREW - 4 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the UPRIGHTS (C and D). Do not tighten the TWIST-LOCK® FASTENERS in this step. 7F D C Page 6 420569 www.sauder.
Step 2 å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), PANEL (F), and SHELF (G). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 2F (14 used) 1F G F B A Arrow D C Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.
Step 3 å Fasten the LEFT END (B) and LEFT UPRIGHT (D) to the TOP (E). Tighten three HIDDEN CAMS. Some assembly (and snacks) required. Angled edge Finished edge withM e c fa A Sur DEN C D HID B withMS e c fa A Sur DEN C HID Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 4 å å Insert four METAL PINS (1R) into the SMALL SHELF (H). Insert the METAL PINS (1R) in one end of the SMALL SHELF (H) into the holes in the LEFT UPRIGHT (D). Finished edge D H 1R www.sauder.
Step 5 å Fasten the RIGHT UPRIGHT (C) to the TOP (E) and SMALL SHELF (H). Tighten the HIDDEN CAM. å NOTE: Be sure the PINS in the SMALL SHELF (H) insert into the holes in the RIGHT UPRIGHT (C). å With a hammer, tap the DOOR STOP (5R) into the small hole in the SHELF (G) as shown in the lower diagram. Maximum 210 degrees Arrow Minimum 190 degrees Angled edge H C E G t ou th S wi AM ce C rfa EN Su IDD H 5R Page 10 420569 www.sauder.
Step 6 å Fasten two HINGE SPACERS (22H) and two HINGES (13H) to the FLIP-UP DOOR (J). Use four SILVER 5/8" FLAT HEAD SCREWS (23S). 23S SILVER 5/8" FLAT HEAD SCREW (4 used in this step) 13H 22H 13H J 22H www.sauder.
Step 7 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the FLIP-UP DOOR (J) to the SMALL SHELF (H). Use the screws in the HINGE. See step 9 for adjustments. å NOTE: The top edge of the DOOR (J) and the top surface of the SMALL SHELF (H) should be even. å Fasten the KNOB (186K) to the FLIP-UP DOOR (J).
Step 8 å Fasten the SHELF (G) to the UPRIGHTS (C and D). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the CAM DOWELS in the SHELF insert into the holes in the LEFT END (B). å Fasten the SHELF (G) to the LEFT END (B). Tighten two HIDDEN CAMS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2.
Step 9 å å å NOTE: You will need a short screwdriver in this step. å DOOR ADJUSTMENTS: To adjust the DOORS up and down (vertical), turn the adjusting screw in or out. å To adjust the DOORS side to side (horizontal), loosen both horizontal adjustment screws. Move the DOOR left or right to the desired location. Tighten the screws after making adjustments. å Refer to the enlarged diagram to identify the parts on the HINGES. The DOOR may need some adjustments.
Step 10 å å Fasten three ANGLE BRACKETS (5G) to the PANEL (F). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). Now might be a good time to refresh your drink. NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the PANEL. ce rfa Su th wi EN DD HI S M CA F 5G 1S BLACK 9/16" LARGE HEAD SCREW (3 used in this step) www.sauder.
Step 11 å å Carefully stand your unit on its TOP (E). å Fasten the PANEL (F) to the SHELF (G). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS and into the SHELF. Maximum 210 degrees Fasten the PANEL (F) to the LEFT END (B). Tighten two HIDDEN CAMS. Arrow Minimum 190 degrees 1S B BLACK 9/16" LARGE HEAD SCREW (3 used in this step) Sur HIDface w DEN ith CA MS F G E Page 16 420569 www.sauder.
Step 12 å Fasten the RIGHT END (A) to the TOP (E), PANEL (F), and SHELF (G). Tighten six HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees ut itho S w e fac AM Sur DEN C HID F A G E Angled edge www.sauder.
Step 13 å Carefully turn your unit over onto its front edges. Unfold the BACK (I) and lay it over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (I) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (C and D) and SMALL SHELF (H).
Step 14 å å å Carefully stand your unit upright. å Fasten the HEADBOARD BRACKETS (16G) to the ENDS (A and B). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Use the holes that are best suited for the height of your bedframe. å NOTE: If you purchased the Mates Bed #420568 go to the next step on how to fasten it to this unit. å Push a CAM COVER (12P ) onto each HIDDEN CAM. Push the RUBBER SLEEVES (2R) over the METAL PINS (1R).
Step 15 å Finish drilling out four 1/4" holes in the END of the #420568 Mates Bed that will get fastened to the Twin Headboard. Fasten the Mates Bed to the Twin Headboard with four SILVER 1-1/4" BOLTS (117S), WASHERS (13M), and NUTS (24M). å å Go to Step 16 of the Mates Bed instruction book to complete the assembly of that unit. This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story at walmart.
Tête de Lit-Bibliothèque pour lit une place Modèle 420569 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision.
ÉTAPE 1 ÉTAPE 6 REMARQUE : Ne pas serrer les FIXATIONS TWIST-LOCK® à ce stade de l'assemblage. Fixer deux RONDELLES D'ESPACEMENT DE CHARNIÈRE (22H) et deux CHARNIÈRES (13H) à la PORTE ABATTANTE (J). Utiliser quatre VIS TÊTE PLATE 16 mm ARGENTÉES (23S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) dans les gros trous des MONTANTS (C et D).
ÉTAPE 9 ÉTAPE 13 REMARQUE : Il faudra peut-être utiliser un tournevis court pour cette étape. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (I) et le placer sur l'élément. Il faut peut-être ajuster la PORTE. Suivre les indications ci-dessous pour ajuster.
Cabecera para cama sencilla con biblioteca Modelo 420569 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 NOTA: No apriete los SUJETADORES TWIST-LOCK® por ahora. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije dos ESPACIADORES DE BISAGRA (22H) y dos BISAGRAS (13H) a la PUERTA ABATIBLE HACIA ARRIBA (J). Utilice cuatro TORNILLOS PLATEADOS DE CABEZA PERDIDA de 16 mm (23S). Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes de los PARALES (C y D).
PASO 9 PASO 13 NOTA: Usted puede necesitar la utilización un destornillador corto para este paso. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (I) y colóquelo sobre la unidad. La PUERTA puede requerir ajustes. Siga el texto abajo para hacer los ajustes necesarios.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.