CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Mates Bed Model 423003 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-20 Hammer Français 21-23 Español 24-26 Warranty Page 2 Not actual size 27 423003 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push sixteen HIDDEN CAMS (1F) into the BACK PANEL (C), CENTER SUPPORT (D), RAILS (E and F) and DRAWER BRACES (M65). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. 2F Arrow Do not tighten the HIDDEN CAMS in this step.
Step 2 VIEW THE DRAWER GLIDE VIDEO å Fasten two UNIVERSAL CABINET RAILS* (40DA) to the HEADBOARD/FOOTBOARDS (B) exactly as shown. Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system Remember: Righty tighty. Lefty loosey. 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) A tracking label will be on one of these surfaces. Please do not remove. Glide end 1 4 2 3 B 3 2 4 1 Glide end B Rounded edge Page 6 Rounded edge 423003 www.sauder.
Step 3 VIEW THE DRAWER GLIDE VIDEO å Fasten the remaining UNIVERSAL CABINET RAILS* (40DA) to each surface of the CENTER SUPPORT (D) exactly as shown. Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å Fasten the SUPPORT BRACKET (11B) to the CENTER SUPPORT (D). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Position the BRACKET exactly as shown.
Step 4 å With a hammer, tap twelve TACK GLIDES (12E) into the long edges of the HEADBOARD/FOOTBOARDS (B), BACK PANEL (C), CENTER SUPPORT (D), and LOWER RAIL (F). C 12E F This SUPPORT BRACKET must be here. B B D Unfinished edge 12E Page 8 423003 www.sauder.
Step 5 å First, fill the center holes in the short edges of the BACK PANEL (C) 1/4 to 1/2 full with GLUE (177M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the hole in the HEADBOARD/FOOTBOARD (B) 1/4 to 1/2 full with GLUE. Fasten the HEADBOARD/FOOTBOARD (B) to the BACK PANEL (C). Tighten two HIDDEN CAMS. Wipe away the excess glue. å NOTE: Be sure the WOOD DOWEL in the BACK PANEL inserts into the hole in the HEADBOARD/FOOTBOARD.
Step 6 å First, fill the holes in the short edges of the CENTER SUPPORT (D) 1/4 to 1/2 full with GLUE (177M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. 177M å Now, fill the center hole in the BACK PANEL (C) 1/4 to 1/2 full with GLUE. Fasten the CENTER SUPPORT (D) to the BACK PANEL (C). Tighten two HIDDEN CAMS. Wipe away the excess GLUE. å NOTE: Be sure the WOOD DOWEL in the CENTER SUPPORT inserts into the hole in the BACK PANEL.
Step 7 å First, fill the holes in the short edges of the LOWER RAIL (F) 1/4 to 1/2 full with GLUE (177M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the hole in the HEADBOARD/FOOTBOARD (B) and the hole closest to the finished edge in the back surface of the LOWER RAIL (F) 1/4 to 1/2 full with GLUE. Fasten the LOWER RAIL (F) to the HEADBOARD/FOOTBOARD (B) and CENTER SUPPORT (D). Tighten two HIDDEN CAMS. Wipe away the excess GLUE.
Step 8 å First, fill the holes in the short edges of the UPPER RAIL (E) 1/4 to 1/2 full with GLUE (177M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the hole in the HEADBOARD/FOOTBOARD (B) 1/4 to 1/2 full with GLUE. Fasten the UPPER RAIL (E) to the HEADBOARD/FOOTBOARD (B) and CENTER SUPPORT (D). Tighten two HIDDEN CAMS. Wipe away the excess GLUE. å NOTE: Be sure the WOOD DOWEL in the RAIL inserts into the hole in the HEADBOARD/FOOTBOARD.
Step 9 å First, fill the holes in the remaining HEADBOARD/ FOOTBOARD (B) 1/4 to 1/2 full with GLUE (177M). Drop glue into the exact holes shown to the right. å Fasten the HEADBOARD/FOOTBOARD (B) to the BACK PANEL (C) and RAILS (E and F). Tighten five HIDDEN CAMS. Wipe away the excess GLUE. å NOTE: Be sure the WOOD DOWELS in the BACK PANEL and RAILS inserts into the holes in the HEADBOARD/FOOTBOARD. 177M Sur B fac ew ith hol es Rounded edge 177M Fill the holes 1/4 to 1/2 full with GLUE.
Step 10 å Fasten four CLEATS (G) to the BACK PANEL (C) and UPPER RAIL (E). Use twelve BLACK 1-1/8" PAN HEAD SCREWS (9S). 9S BLACK 1-1/8" PAN HEAD SCREW (12 used in this step) G C G G G Page 14 E 423003 www.sauder.
Step 11 å Fasten the remaining CLEATS (G) to the HEADBOARD/ FOOTBOARDS (B). Use six BLACK 1-1/8" PAN HEAD SCREWS (9S). Don't worry. It isn't Rome. This can be built in a day. 9S BLACK 1-1/8" PAN HEAD SCREW (6 used in this step) G B G B www.sauder.
Step 12 VIEW THE T-SLOT BOX VIDEO Push down 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 8G B30 H D213 D212 Unfi nish ed sur fac e H 1S D212 D213 BLACK 9/16" LARGE HEAD SCREW (8 used in this step) å Pull the DRAWER FRONT BRACKETS (8G) apart and slide them into the grooves in the DRAWER SIDES (D212 and D213). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification.
Step 13 VIEW THE DRAWER GLIDE VIDEO å Fasten a DRAWER RIGHT (40DC) to the RIGHT DRAWER SIDE (D212) and a DRAWER LEFT (40DD) to the LEFT DRAWER SIDE (D213). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å NOTE: The glides are not intended to rotate. å Repeat this step for the LEFT DRAWER. Fasten a PULL (149K) to the RIGHT DRAWER FRONT (H). Use two SILVER 1/4" MACHINE SCREWS (61S) and two BROWN PLASTIC WASHERS (151M).
Step 14 å If you purchased the 422892 Headboard, assemble that unit now. The Headboard attachment will be shown in the 422892 Headboard instruction book. å NOTE: The diagrams below show the 422892 Headboard on the left or right of this Platform Bed. 422892 HEADBOARD on the right 422892 HEADBOARD on the left Page 18 423003 www.sauder.
Step 15 å Fasten the BOTTOMS (A2) to the CLEATS (G). Use ten BLACK 1-1/2" FLAT HEAD SCREWS (101S). Almost time to celebrate! With a nap. 101S BLACK 1-1/2" FLAT HEAD SCREW (10 used in this step) G A2 A2 G www.sauder.
Step 16 å To insert the drawers into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. å To make adjustments to the drawer, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story at Walmart.com or 25 lbs. H 25 lbs.
Modèle 423003 Lit Mates Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Attention: Examiner bien les pièces avant d'assembler. Il est difficile de séparer des pièces une fois encollées. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer seize EXCENTRIQUES ESCAMOTABLES (1F) dans le PANNEAU ARRIÈRE (C), le SUPPORT CENTRAL (D), les TRAVERSES (E et F) et les ENTRETOISES DE TIROIR (M65).
ÉTAPE 9 ÉTAPE 13 Tout d'abord, remplir les trous dans l’autre TÊTE DE LIT/PIED DE LIT (B) de 1/4 à 1/2 pleins de COLLE (177M). Mettre colle dans les trous exacts illustrés à la droite. Fixer un TIROIR DROIT (40DC) sur le CÔTÉ DROIT DE TIROIR (D212) et un TIROIR GAUCHE (40DD) sur le CÔTÉ GAUCHE DE TIROIR (D213). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 2. Fixer la TÊTE DE LIT/PIED DE LIT (B) sur le PANNEAU ARRIÈRE (C) et TRAVERSES (E et F).
Modelo 423003 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Precaución: Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciséis EXCÉNTRICOS ESCONDIDOS (1F) en el PANEL POSTERIOR (C), al SOPORTE DEL CENTRO (D), a los RIELES (E y F) y a las RIOSTRAS DE CAJÓN (M65).
PASO 9 PASO 13 Primero, llene los agujeros en la otra CABECERA / otro PIE DE CAMA (B) entre 1/4 a 1/2 con PEGAMENTO (177M). Coloque pegamento en los agujeros correspondientes indicados que se muestran a la derecha. Fije un CAJÓN DERECHO (40DC) al LADO DERECHO DE CAJÓN (D212) y un CAJÓN IZQUIERDO (40DD) al LADO IZQUIERDO DE CAJÓN (D213). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 2.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
