CONTACT CONTACTUS USFIRST FIRST sauder.com BEFORE BEFOREMAKING MAKINGANY ANYRETURNS RETURNSTO TOTHE THESTORE. STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-445-1527. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) The stories of your life. 5-Shelf Bookcase Model 423733 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Table of Contents Hardware Identification Part Identification Assembly Steps Assembly Tools Required 2 No. 2 Phillips Screwdriver Tip Shown Actual Size 3 4-14 Hammer Français 15-17 Español 18-20 Safety 21-22 Warranty Not actual size Skip the power trip. This time. 23 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1 HIDDEN CAM - 46 4 TACK GLIDE - 4 10 Page 2 NAIL - 46 2 5 3 CAM SCREW - 46 99 APPLIQUE CARD - 5 11 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Some assembly (and snacks) required. Push forty-six HIDDEN CAMS (1) into the ENDS (A, B, C, and D), TOP (E), BOTTOM (F), SHELF (G), and ADJUSTABLE SHELVES (H).
Step 2 å Turn forty-six CAM SCREWS (2) into the ENDS (A, B, C, and D), SHELF (G), SHELF MOLDINGS (J and L), VALANCE (K), BASE (M), and END MOLDINGS (N and O). 2 G D C B K M A L J O O J N J N 423733 www.sauder.
Step 3 å Fasten the UPPER ENDS (A and B) to the TOP (E). Tighten four HIDDEN CAMS. 1 Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 2 Finished edge S AM C DEN HID A ith ew c a f Sur Sur fac ew E ith HID DEN CA MS Edge with HIDDEN CAMS S AM C DEN HID B out h t i ew fac r u S Edge with HIDDEN CAMS Page 6 www.sauder.
Step 4 å Fasten the SHELF (G) to the UPPER ENDS (A and B). Use four SILVER 1-1/2" FLAT HEAD SCREWS (11). A Finished edge B G Sur fac ew ith HID DEN CA MS Edge with HIDDEN CAMS 11 SILVER 1-1/2" FLAT HEAD SCREW (4 used in this step) 423733 www.sauder.
Step 5 å First, fasten the LOWER ENDS (C and D) to the BOTTOM (F). Tighten four HIDDEN CAMS. å Then, fasten the LOWER ENDS (C and D) to the SHELF (G). Tighten four HIDDEN CAMS. C Just think. The sooner you do this, the sooner you do something else. 1st ith e w AMS c a f Sur DEN C D HI Edge with HIDDEN CAMS Sur fac F ew ith HID DEN CA MS D out h t i ew fac r u S MS CA N DE HID Edge with HIDDEN CAMS 2nd G C D Page 8 www.sauder.
Step 6 å Unfold the SMALL BACK (Q) and lay it over the bottom of your unit. å Make equal margins along all four edges of the SMALL BACK (Q). Push on opposite corners of your unit if needed to make it "square". å Fasten the bottom and side edges of the SMALL BACK (Q) to your unit using the NAILS (10). å NOTE: Do not fasten the upper edge of the SMALL BACK at this time. å å Repeat this step for the LARGE BACK (P). Caution Do not stand the unit upright without the BACK fastened.
Step 7 å å Carefully turn your unit over onto its back. å Fasten the UPPER END MOLDINGS (N) to the UPPER ENDS (A and B). Tighten six HIDDEN CAMS. Fasten the VALANCE (K) to the TOP (E) and UPPER ENDS (A and B). Tighten five HIDDEN CAMS. K N Curved edge E B N A Curved edge These surfaces should be even. Page 10 www.sauder.
Step 8 å Fasten the SHELF MOLDING (L) to the SHELF (G). Tighten three HIDDEN CAMS. å Fasten the LOWER END MOLDINGS (O) to the LOWER ENDS (C and D). Tighten six HIDDEN CAMS. These surfaces should be even. Curved edge L O D G O C Curved edge These surfaces should be even. 423733 www.sauder.
Step 9 å Fasten the BASE (M) to the LOWER ENDS (C and D) and BOTTOM (F). Tighten five HIDDEN CAMS. å With your hammer, gently tap the TACK GLIDES (4) into the bottom edges of the LOWER ENDS (C and D) and BASE (M). If you're doing this to help a friend, don't leave without a bite. D M F C 4 Page 12 www.sauder.
Step 10 å å Carefully stand your unit upright. å å å å Place your unit in its final location against a wall. We recommend using the FURNITURE TIPPING RESTRAINT KIT (99) for added stability. Fasten a bracket to the center of the back edge of the TOP (E) and 1/4" down from the top edge using the 5/8" screw as shown. Follow the instructions included in the KIT to fasten your unit to the wall. Insert the METAL PINS (3) into the hole locations of your choice in the ENDS (A, B, C, and D).
Step 11 å å å å å Fasten an ADJUSTABLE SHELF MOLDING (J) to one of the ADJUSTABLE SHELVES (H). Tighten three HIDDEN CAMS. Repeat this step for the remaining ADJUSTABLE SHELVES (H) and ADJUSTABLE SHELF MOLDINGS (J). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS in the ENDS (A, B, C, and D). NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth. Wipe dry.
Modèle 423733 Bibliothèque avec 5 tablettes Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Tout d'abord, fixer les EXTRÉMITÉS INFÉRIEURES (C et D) au DESSOUS (F). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Enfoncer quarante-six EXCENTRIQUES ESCAMOTABLES (1) dans les EXTRÉMITÉS (A, B, C et D), le DESSUS (E), le DESSOUS (F), la TABLETTE (G) et les TABLETTES RÉGLABLES (H). Fixer ensuite les EXTRÉMITÉS INFÉRIEURES (C et D) à la TABLETTE (G).
ÉTAPE 7 ÉTAPE 10 Avec précaution, retourner l'élément sur l’arrière. Relever, avec précaution, l'élément dans sa position verticale. Fixer le LAMBREQUIN (K) au DESSUS (E) et aux EXTRÉMITÉS SUPÉRIEURES (A et B). Serrer cinq EXCENTRIQUES ESCAMOTABLES. Il est recommandé d’utiliser le KIT DE RETENUE ANTIBASCULEMENT POUR MOBILIER (99) pour stabilité additionnelle.
Modelo 423733 Biblioteca con 5 estantes Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Primero, fije los EXTREMOS INFERIORES (C y D) al FONDO (F). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Empuje cuarenta y seis EXCÉNTRICOS ESCONDIDOS (1) en los EXTREMOS (A, B, C y D), el PANEL SUPERIOR (E), el FONDO (F), el ESTANTE (G) y los ESTANTES AJUSTABLES (H). A continuación, fije los EXTREMOS INFERIORES (C y D) al ESTANTE (G). Apriete cuatro EXCÉNTRICOS ESCONDIDOS.
PASO 7 PASO 10 Cuidadosamente voltee la unidad para que repose sobre el dorso. Cuidadosamente ponga la unidad en posición vertical. Fije la CORNISA (K) al PANEL SUPERIOR (E) y a los EXTREMOS SUPERIORES (A y B). Apriete cinco EXCÉNTRICOS ESCONDIDOS. Le recomendamos utilizar el KIT DE CONTROL ANTIINCLINACIÓN PARA MOBILIARIO (99) para dar más estabilidad.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados. • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-445-1527 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
