CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) Guaranteed to hold other beverages, too. Lift-Top Coffee Table Model 427463 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-23 Français 24-26 Español 27-29 Safety 30 Warranty 31 Hammer Not actual size Short Screwdriver Adjustable Wrench Page 2 427463 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (37F) into the large holes in the BACK PANEL (C) and FRONT PANEL (K). Do not tighten the TWIST-LOCK® FASTENERS in this step. 37F C K 37F www.sauder.
Step 2 å Push four HIDDEN CAMS (1F) into the SHELF (D). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. 2F (4 used) Arrow 1F s le ho es th dg wi rt e ce ho rfa e s Su th on D Arrow Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Page 6 427463 www.sauder.
Step 3 å Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), BOTTOM (E), and PANELS (C and K). Just think. The sooner you do this, the sooner you do something else. Arrow 1F (20 used) E C K Arrow B 1F A Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 4 å Turn twenty CAM SCREWS (8F) into the LEGS (F and G). (20 used) 8F F F G G 8F Page 8 427463 www.sauder.
Step 5 å Fasten the RIGHT END (A) to the LEGS (F and G). Tighten four HIDDEN CAMS. å NOTE: Be sure to position the LEGS exactly as shown. 1 2 G These small holes should be closer to this edge. These holes must be here. A F www.sauder.
Step 6 å Fasten the LEFT END (B) to the LEGS (F and G). Tighten four HIDDEN CAMS. å NOTE: Be sure to position the LEGS exactly as shown. F These small holes should be closer to this edge. These holes must be here. B G Page 10 427463 www.sauder.
Step 7 å Fasten the PANELS (C and K) to the SHELF (D). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 8 å Fasten the SHELF (D) and PANELS (C and K) to the RIGHT END (A) and LEGS (F and G). Tighten six HIDDEN CAMS. C Surf HID ace with DEN CAM S K D This PANEL has a groove. These holes are closer to this leg. G A F Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 12 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 427463 www.sauder.
Step 9 å Fasten the BOTTOM (E) to the LEGS (F and G). Tighten two HIDDEN CAMS. Sur HIDface w DEN ith CA MS E G F www.sauder.
Step 10 å Fasten the LEFT END (B) and LEGS (F and G) to the SHELF (D), BOTTOM (E), and PANELS (C and K). Tighten eight HIDDEN CAMS. å NOTE: Use the Short Screwdriver to tighten the HIDDEN CAMS in the SHELF. Now might be a good time to refresh your drink. F B C G K D E Page 14 427463 www.sauder.
Step 11 å Fasten twelve METAL BRACKETS (4G) to the BOTTOM (E). Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure four of the BRACKETS are even with the SHORT edges of the BOTTOM. å Fasten the SKIRTS (H and I) to the BOTTOM (E). Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS and into the SKIRTS. å NOTE: There are no pre-drilled holes in the SKIRTS. The SCREWS will tighten into the grooves.
Step 12 å Using your hammer, gently tap four TACK GLIDES (13E) into the bottoms of the LEGS (F and G). 13E F G G F Page 16 427463 www.sauder.
Step 13 å å Carefully stand your unit upright. å Fasten the PULLS (131K) to the FRONT PANEL (K). Use four SILVER 1/2" MACHINE SCREWS (38S). Push six BUMPERS (2M) into the PANELS (C and K) and LEGS (F and G). 2M G C F K F 131K G 38S SILVER 1/2" MACHINE SCREW (4 used for the PULLS) www.sauder.
Step 14 å Fasten the LIFT TABLE MECHANISMS (23M) to the TOP (L). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure to position the LIFT TABLE MECHANISMS on the TOP exactly as shown. 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) Meet Part (L). This component has been engineered to be lighter, stronger, faster… well ok. Not technically faster. But definitely makes for a sturdier Lift-Top Coffee Table that’s easier to assemble and friendlier to the environment.
Step 15 å å Fasten the SUPPORT BRACKETS (37G) to the LIFT TABLE MECHANISMS (23M). Use four WASHERS (13M), NUTS (24M), and BLACK 3/4" MACHINE SCREWS (92S). 92S NOTE: Use the adjustable wrench in this step. BLACK 3/4" MACHINE SCREW (4 used in this step) 13M 37G 92S 24M 23M 24M 23M 92S 37G 13M www.sauder.
Step 16 å å IMPORTANT: You will need someone's help in this step. å NOTE: Be careful when lining up the holes in the MECHANISMS with the holes in the ENDS as to not damage any parts. You should start each SCREW a few turns before completely tightening any of them. Fasten the TOP (L) to the ENDS (A and B). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S) through the LIFT TABLE MECHANISMS (23M) and into the holes in the ENDS.
Step 17 å Finish, fastening the TOP (L) to the ENDS (A and B). Use two BUSHINGS (91M), WASHERS (13M), and BLACK 3/4" PAN HEAD SCREWS (85S) through the exact holes shown in the LIFT TABLE MECHANISMS (23M) and into the holes in the ENDS. å NOTE: Do not overtighten the SCREWS (85S). If you're doing this to help a friend, don't leave without a bite. Do not overtighten the SCREWS (85S). L 23M A 23M B 13M 91M 85S 91M BLACK 3/4" PAN HEAD SCREW (2 used for the BUSHINGS) 13M www.sauder.
Step 18 å Fasten the STRETCHER (J) to the SUPPORT BRACKETS (37G) on the LIFT TABLE MECHANISMS (23M). Use four WASHERS (13M), NUTS (24M), and BLACK 1-1/4" MACHINE SCREWS (93S). å NOTE: Use the adjustable wrench in this step. 93S BLACK 1-1/4" MACHINE SCREW (4 used in this step) 24M 24M 37G J 23M 23M 13M 37G 13M 93S Page 22 427463 www.sauder.
Step 19 å å å å IMPORTANT: Do not place valuables in the storage space. Peel APPLIQUES from the APPLIQUE CARD (93P) and stick them onto each visible HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story at Walmart.com or 40 lbs. 25 lbs. 40 lbs. 93P (20 used) To cover HIDDEN CAMS www.sauder.
Modèle 427463 Table basse à dessus relevable Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer les PANNEAUX (C et K) à la TABLETTE (D). Serrer quatre FIXATIONS TWIST-LOCK®. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (37F) dans les gros trous dans le PANNEAU ARRIÈRE (C) et le PANNEAU AVANT (K). ÉTAPE 2 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape.
ÉTAPE 11 ÉTAPE 16 Fixer douze CONSOLES EN MÉTAL (4G) au DESSOUS (E). Utiliser douze VIS TÊTE LARGE 14 mm NOIRES (1S). IMPORTANT : Faire appel à une autre personne pour cette étape. REMARQUE : S'assurer que quatre des CONSOLES sont à fleur des chants COURTS du DESSOUS. Fixer les PLINTHES (H et I) au DESSOUS (E). Utiliser douze VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les CONSOLES et dans les PLINTHES. REMARQUE : Les PLINTHES ne comportent pas de trous prépercés. Serrer les VIS dans les rainures.
Modelo 427463 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije los PANELES (C y K) al ESTANTE (D). Apriete cuatro SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (37F) dentro de los agujeros grandes del PANEL POSTERIOR (C) y el PANEL DELANTERO (K). PASO 2 Cómo utilizar el SUJETADOR TWIST-LOCK® SAUDER 1.
PASO 11 PASO 16 Fije doce SOPORTES DE METAL (4G) al FONDO (E). Utilice doce TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). IMPORTANTE: Necesitar la ayuda de otra persona para este paso. NOTA: Asegúrese que cuatro de los SOPORTES estén nivelados con los bordes CORTOS del FONDO. Fije los FALDONES (H e I) al FONDO (E). Pase doce TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S) a través de los SOPORTES y en los FALDONES. Fije el PANEL SUPERIOR (L) a los EXTREMOS (A y B).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
