LOT NUMBER: DATE PURCHASED: / / Bankston Dining Bench Stock # BH13-022-599-01 # BH19-D1-1011-04 # BH19-D1-1011-05 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS 1. Maximum load weight on bench is 275 pounds (124.7 kg). THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY. GENERAL INFORMATION, TIPS AND TRICKS 1. Please read the Assembly Instructions prior to assembling the unit. 2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface. 3.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Bench Top (Qty. 1) B- Left Front/Right Back Leg (Qty. 2) C- Right Front/Left Back Leg (Qty. 2) D- Side Stretcher (Qty. 2) (1) Hex Nut (Qty. 8+1 extra) (4) 1 1/2” Wood Screw (Qty. 4+1 extra) (2) Lock Washer (Qty. 8+1 extra) (5) M10 x 35 mm Wood Dowel (Qty. 4+1 extra) (3) Flat Washer (Qty. 8+1 extra) Open Wrench (Qty.
Assembly Instructions A 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Place the Bench Top (A) upside down on a level and protected surface as shown. 3. Remove the additional wood blocks attached at the corners of Bench Top (A) by unscrewing the wood screws. These are used for shipping purposes only. After removing them, please discard.
Assembly Instructions C C Hex Nut (2 used in this step) ① 3 2 1 Lock Washer (2 used in this step) A C ② Flat Washer (2 used in this step) A ③ DO NOT fully-tighten the nuts or bolts initially until all the nuts or bolts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts. 4. Remove the plastic caps from the hanger bolts of all the Legs (B and C). 5. Attach one Leg (C) to the apron corner of the Bench Top (A) as shown.
Assembly Instructions B B/C 5 4 D 3 2 A 1 C D B 1-1/2” Wood Screw (2 used in this step) A ④ Hex Nut (2 used in this step) ① Flat Washer (2 used in this step) Lock Washer (2 used in this step) Wood Dowel (2 used in this step) ③ ② ⑤ 6. Insert a Wood Dowel (5) into the large hole on each end of one Side Stretcher (D). Attach the Side Stretcher (D) to the assembled Leg (C) with the wood dowel fully inserted. 7.
Assembly Instructions B/C 5 4 D B D A C C Hex Nut (4 used in this step) ① Flat Washer (4 used in this step) ③ Lock Washer (4 used in this step) A 3 2 1 ② 1-1/2” Wood Screw (2 used in this step) Wood Dowel (2 used in this step) ④ ⑤ 9. Repeat the same process to assemble the remaining Legs (B and C) and the Side Stretcher (D) at the other end of the Bench Top (A). 10. Go back and securely tighten all the nuts with the enclosed open wrench.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
LOTE No.: FECHA DE COMPRA: / / Banca Bankston Serie # BH13-022-599-01 # BH19-D1-1011-04 # BH19-D1-1011-05 ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMO PESO RECOMENDADO 1. Máxima carga es de 275 libras (124.7 kg). ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRÍA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. INFORMACIÓN GENERAL, RECOMENDACIONES Y TRUCOS 1. Por favor lea el instructivo antes de comenzar el ensamble. 2. Para evitar daños, ensamble la unidad en una area nivelada y libre de abrazivos. 3. Mantener el Herraje fuera de las manos de los niños. 4.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y ferretería antes de iniciar el ensamblado. A- Superficie de Banca (Cant. 1) B- Pata izq. frontal/ der. posterior (Cant. 2) C- Pata der. frontal/ izq. posterior (Cant. 2) (1) Tuerca hexagonal (Cant. 8+1 extra) (4) 1-1/2” Tornillo (Cant. 4+1 extra) D- Soportes laterales (Cant. 2) (2) Arandela de presión (Cant. 8+1 extra) (5) M10 x 35 mm Perno madera (Cant.
Instructivo de ensamble A 1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas. Ensamblar la unidad sobre en una área encarpetada o el cartón vacío para evitar cualquier rasguño. 2. Posicionar la superficie de banca (A) boca abajo sobre una superficie plana y protegida, como se muestra. 3. Retire los bloques de madera adicionales unidos en las esquinas de la banca (A) aflojando los tornillos de madera. Estos se utilizan sólo con fines de envío.
Instrucciones de ensamble C C Tuerca hexagonal (2 usados en este paso) ① 3 2 1 Arandela de presión (2 usados en este paso) A C ② Arandela plana (2 usados en este paso) A ③ NO APRIETE completamente los tornillos o tuercas hasta que todas las partes esten ensambladas. Para evitar daños a la rosca no apriete demas los tornillos o tuercas. 4. Remover los protectores de plástico de los tornillos de las patas (B y C). 5.
Instrucciones de ensamble B B/C 5 4 D 3 2 A 1 C D B A (2 usados en este paso) ① (2 usados en este paso) ④ Arandela plana Tuerca hexagonal 1-1/2” Tornillo (2 usados en este paso) Arandela de presión (2 usados en este paso) ③ ② Perno de madera (2 usados en este paso) ⑤ 6. Insertar un perno de madera (5) en el orificio grande en cada extremo del soporte lateral (D). Coloque el soporte lateral (D) a la pata ensamblada (C) con el perno de madera insertado completamente. 7.
Instrucciones de ensamble B/C 5 4 D B D A C C Tuerca hexagonal (4 usados en este paso) ① Arandela de presión (4 usados en este paso) A 3 2 1 ② Arandela plana (4 usados en este paso) ③ Tornillo de 1-1/2” (2 usados en este paso) Perno de madera (2 usados en este paso) ④ ⑤ 9. Repetir el mismo proceso a las patas restantes (B y C) y el soporte lateral (D) al otro extremo de la superficie de banca (A). 10. Vuelva y apriete todas las tuercas hexagonales con la llave española incluida.
Mantenimiento y cuidados Use una toalla suave y limpia para evitar daños y rayaduras. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Los derrames de líquidos se deben de limpiar inmediatamente, con una toalla suave evitando tallar.