9-CUBE ORGANIZER VENDOR STOCK NUMBERS BHAJI-084-099-05-ESPRESSO BHAJI-084-099-06-WHITE BHAJI-084-099-07-WEATHERED BHAJI-084-099-12-BIRCH BHAJI-084-099-17-BLACK BHAJI-084-099-23-GRAY BHAJI-084-099-24-PINK BHAJI-084-098-18-RUSTIC GRAY THIS PRODUCT MUST ALWAYS BE MOUNTED TO A WALL OR STUD FOR USE. TOP PANEL MAXIMUM LOAD 100 LB (45.5 KG) MAXIMUM LOAD 30 LB (13.6 KG) {EACH CUBE) RECOMMENDED NUMBER OF PEOPLE FOR ASSEMBLY: 1 ESTIMATED ASSEMBLY TIME: 1 HOUR ADDITIONAL PARTS ARE AVAILABLE FOR A FEE.
A BEFORE STARTING TOOLS NEEDED TO ASSEMBLE Read and understand all the steps carefully before starting. If each step s not followed in the correct order the assembly will be difficult and may result in dosages. Work in a spacious are, preferably on a carpeted surface, near where the unit will be used. Make sure all the parts are included. Most boards are labeled with a removable sticker. Helpful hints Call our toll free number if you need assistance.
Top/bottom panel Fixing middle shelf (Qty: 2) (Qty: 2) Side panel Partition beard (Qty: 2) (Qty: 6) We are available to assist you Monday -Friday from 9:00 am 5:00 pm Easter Standard Time. VERIFY THAT ALL PARTS ARE LISTED BEFORE BEGINNING 1-800-729-1569 USA only.
WWW Qi . Screw bolt Spring washer Washer Cam bolt Qty: 8 Qty: Wood dowel Safety strap kit Allen key Cap Qty: 32+1 Extra Qty: 1 Qty: 1 Qty: 8 We are available to assist you Monday -Friday from 9:00 am 5:00 pm Easter Standard Time. VERIFY THAT ALL PARTS ARE LISTED BEFORE BEGINNING 1-800-729-1569 USA only.
CAM FASTENING SYSTEM Screw the cam bolt into the prevailed panel. The screw should be tightened so no threads are visible. The larger ring of the cam should touch the panel. Insert the cam lock into the prevailed hole in the panel. The plus and minus signs should be facing the outside of the panel. Connect the previously tightened cam bolt with the panel connected into the cam lock. Using a flat head screw driver, turn the cam lock halfway clockwise to secure the cam bolt.
4 wood dowels into 2 part D1 partition boards. Place dowel ] Insert 2 wood dowels into 4 part D1 partition boards. Insert on hole. Gently tap with hammer to insert. Insert with 4 pcs of wood dowel ® at both side.
Screw in the cam bolts into side [ Insert with 4 pcs of wood dowel ® at both side. panel with hand.
Align and attach partition board to the shelves. Align and attach side panels to the structure and then tighten the cam locks.
Tighten all screw bolts with attached Allen key as shown.
8 Now Your Unit Is Completed Fasten the safety strap to the wall using OPTION shown. Option 1: Fasten the strap (7a) to a stud in the wall using the screw (7d} through washer (7b). Option 2 Drill a 3/16" diameter hole in the wallboard. Tap the wall anchor (7e} into the hole until it is flush. Fasten the strap (7a} to the wall rancher {7e) using the screw (7d} through the washer (7b). \% Quality Guarantee Should this product be defective in workmanship or materials or fail under normal use, we will repair or
A ANTES DE COMENZAR HERRAMIENTAS NECESARIAS PARA ENSAMBLAR . Leer y entender todos los pasos cuidadosamente antes de comenzar. si no se sigue cada paso en el orden correcto, el montaje ser difícil y puede ocasionar dacios. . Trabajar en una zona amplia, mejor sobre la alfombra, cerca del sitio donde la unidad se utiliza. . Asegurarse de que todas las piezas estén incluidos. La mayoría de los tableros estén etiquetados con una pegatina re movible. Consejos Otiles . Limar a nuestro minero gratis para ayuda.
Barra arriba/abajo Estante del medio para fijación {Cantidad: 2) (Cantidad: 2} Barra lateral Tabla de tabique (Cantidad: 2} {Cantidad: 6) Estamos disponibles para ayudarlo de Lunes Viernes VERIFIQUE QUE TODAS LAS PIEZAS ESTÉN EN LA LISTA ANTES de 9:00 am 5:00 pm Era de la Zona Este. DE COMENZAR 1-800-729-1569 Solé EEU.U.
. Atornille Arandela elástica Arandela Tornillo de combadura Cerrojo de combadura Cantidad: 8 Cantidad: 8 Cantidad: 8 Cantidad: 8 Cantidad: 8 ©@ Clavija de madera Cinturón Lave alelen Tapen Cantidad: 32+1 Extra Cantidad: 1 Cantidad: 1 Cantidad: 8 Estamos disponibles para ayudarlo de Lunes Viernes VERIFIQUE QUE TODAS LAS PIEZAS ESTÉN EN LA LISTA ANTES de 9:00 am 5:00 pm Era de la Zona Este. DE COMENZAR 1-800-729-1569 Solé EEU.U.
SISTEMA DE FIJACIÓN CAM Atornille el Tornillo de combadura en el panel pre taladrado. El tornillo debe apretarse para que no haya roscas visibles. El anillo més grande del cam debe tocar el panel. Inserte el Cerrojo de combadura en el agujero pre taladrado en el panel. Los signos de mds y menos deben estar orientados hacia el exterior del panel. Conecte el Tornillo de combadura previamente apretado con el panel conectado en el Cerrojo de combadura.
tabla de tabique, Insertar 4 clavijas de madera en 2 pedazos de la parte D1 tabla de tabique. Colocar clavija en agujero. Golpear suavemente con un martillo para insertar. ] Insertar 2 clavijas de madera en 4 pedazos de la parte D1 2 Insertar con 4 clavijas de madera ® en ambos lados. | aproa.
Tomillar el cerrojo de combadura en la barra lateral a mano. Insertar con 4 clavijas de madera ® en ambos lados.
Alinear y sujetar la table de tabique con los estantes. Alinear y sujetar la barra lateral con la estructura, y luego apretar el cerrojo de combadura. Por favor de prestar atención a la dirección de las clavijas sobre la table de tabique.
8 Ahora Tu Unidad Estés Compuesta Agujero Abrochar el cinturón con la pared usando OPCIÓN 1 o 2 como lustrado. Opción 1: Abrochar el cinturón (7a) con el clave en la pared usando tormellera {7d) a través de arancel (7b). Opción 2: Perforar un agujero de diámetro 3/16”" en la barra. Espitar la ancla de pared (7e) en el agujero hasta que es quede al mismo nivel. Fijar el cinturón (7a) con la ancla de pared {7e) usando el tornillo (7d} a través de la arandela (7b). \% Garantía de Calidad §i ese producto presen