LOT NUMBER: DATE PURCHASED: / / Collins Dining Table Stock # BH16-084-299-04 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Collins Dining Table (BH16-084-299-04) MADE IN CHINA MAXIMUM LOAD 400 lb. (181.4 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. GENERAL INFORMATION, TIPS AND TRICKS 1. Please read the Assembly Instructions prior to assembling the unit. 2.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Table Top (Qty. 1) B- Leg Assembly (Qty. 2) C- Center Support (Qty. 2) D- Bottom Stretcher (Qty. 1) (1) 1/4" x 3/4" Bolt (Qty. 8+1 extra) (2) 1/4" x 1-1/2" Bolt (Qty. 6+1 extra) (3) Lock Washer (Qty. 14+1 extra) (4) Flat Washer (Qty. 14+1 extra) 4 mm Allen Wrench (Qty. 1) Touch-up Pen (Qty.
Assembly Instructions A DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts. 1. Unpack the unit and confirm that you have all the hardware and required parts. 2. Position the Table Top (A) upside down on a level and protective surface as shown. 3. Remove the additional wood blocks attached at the corners by unscrewing the wood screws. These are used for shipping purposes only.
Assembly Instructions 2 3 42 3 4 2 3 42 3 4 B B A 1/4" x 1-1/2" Bolt Lock Washer (4 used in this step) (4 used in this step) ② ③ Flat Washer (4 used in this step) ④ 4. Attach the Leg Assemblies (B) to the Table Top (A) by inserting four 1-1/2" Bolts (2) with Lock Washers (3) and Flat Washers (4) through the top rail and screw into place. DO NOT fully tighten the bolts.
Assembly Instructions C 1 3 4 1 3 4 C B B A 1/4" x 3/4" Bolt Lock Washer (4 used in this step) (4 used in this step) ① ③ Flat Washer (4 used in this step) ④ 5. Align and attach two Center Supports (C) between the Table Top (A) and the Legs (B) with four 3/4" Bolts (1) and four Washers (3 and 4).
Assembly Instructions 2 3 4 2 3 4 D C B C B A 1/4" x 1-1/2" Bolt Lock Washer (2 used in this step) (2 used in this step) ② ③ Flat Washer (2 used in this step) ④ 6. Attach the Bottom Stretcher (D) to the two Center Supports (C) with two 1-1/2" Bolts (2) and two Washers (3 and 4).
Assembly Instructions 4 1 3 43 1 D B B C C A 1/4" x 3/4" Bolt Lock Washer (4 used in this step) (4 used in this step) ① ③ Flat Washer (4 used in this step) ④ 7. Fasten the Bottom Stretcher (D) to the Legs (B) with four 3/4" Bolts (1) and four Washers (3 and 4).
Assembly Instructions 8. Ask for assistance to lift the assembled unit upright and position it at the desired location. 9. If necessary, adjust the pre-attached Floor Levelers under the Legs (B) to level the unit.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
LOTE NÚMERO: FECHA COMPRA: / / Mesa de Comedor Collins Serie # BH16-084-299-04 ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda donde lo compró.
MÁXIMA CARGA RECOMENDADA FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Mesa de Comedor Collins (BH16-084-299-04) HECHO EN CHINA CARGA MÁXIMA 400 lb. (181.4 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PRODUCTOS ADECUADOS Y PESOS MÁXIMOS INDICADOS. SI SE UTILIZAN OTROS PRODUCTOS O SE EXEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. INFORMACION GENERAL, RECOMENDACIONES Y TRUCOS 1. Por favor lea el instructivo antes de comenzar el ensamble. 2.
Lista de Partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. A- Superficie de mesa (Cant. 1) B- Ensamble de pata (Cant. 2) C- Soporte central (Cant. 2) D- Soporte inferior (Cant. 1) (1) Tornillo 1/4" x 3/4" (Cant. 8+1 extra) (2) Tornillo 1/4" x 1-1/2" (Cant. 6+1 extra) (3) Arandela de presión (Cant. 14+1 extra) (4) Arandela plana (Cant. 14+1 extra) Llave Allen 4 mm (Cant. 1) Plumón de retoque (Cant.
Instrucciones de ensamble A NO APRIETE completamente los tornillos o tuercas hasta que todas las partes esten ensambladas. Para evitar daños a la rosca no apriete demas los tornillos o tuercas. 1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas. 2. Poner la superficie de mesa (A) boca abajo en una area limpia y protegida, como se muestra. 3. Retire los bloques de madera adicionales unidos en las esquinas aflojando los tornillos para madera.
Instrucciones de ensamble 2 3 42 3 4 2 3 42 3 4 B B A Tornillo de 1/4" x 1-1/2" (4 usados en este paso) Arandela de presión (4 usados en este paso) ② ③ Arandela plana (4 usados en este paso) ④ 4. Coloque las patas (B) a la superficie d la mesa (A) mediante la inserción de cuatro tornillos de 1-1/2" (2) con arandelas de presión (3) y arandelas planas (4) a través de la barra superior y fijar en su lugar. NO apretar los tornillos completamente.
Instrucciones de ensamble C 1 3 4 1 3 4 C B B A Tornillo de 1/4" x 3/4" (4 usados en este paso) Arandela de presión (4 usados en este paso) ① ③ Arandela plana (4 usados en este paso) ④ 5. Alinear y colocar dos soportes centrales (C) entre la superficie de la mesa (A) y las patas (B) con cuatro tornillos de 3/4" (1) y cuatro arandelas (3 y 4).
Instrucciones de ensamble 2 3 4 2 3 4 D C B C B A Tornillo de 1/4" x 1-1/2" Arandela de presión (2 usados en este paso) (2 usados en este paso) ② ③ Arandela plana (2 usados en este paso) ④ 6. Coloque el soporte inferior (D) a los dos soportes centrales (C) con dos tornillos de 1-1/2” (2) y dos arandelas (3 y 4).
Instrucciones de ensamble 4 1 3 43 1 D B B C C A Tornillo de 1/4" x 3/4" (4 usados en este paso) Arandela de presión (4 usados en este paso) ① ③ Arandela plana (4 usados en este paso) ④ 7. Apretar el soporte inferior (D) para las patas (B) con cuatro tornillos de 3/4" (1) y cuatro arandelas (3 y 4).
Instrucciones de ensamble 8. Pida ayuda para poner la unidad en posición vertical y posicionar en el lugar deseado. 9. Si es necesario, ajustar los niveladores de piso pre-adjuntos debajo de las patas (B) para nivelar la unidad.
Mantenimiento y cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera revisar en una area que no sea visible para checar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilize protección para vasos cuando ponga sobre la unidad.