LOT NUMBER: DATE PURCHASED: / / Collin 2pk Dining Chair Stock # BH16-084-399-03 White # BH16-084-399-04 Green # BH16-084-399-05 Silver ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS 1. Maximum load weight 136 kg (300 pounds). THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. GENERAL INFORMATION, TIPS & TRICKS 1. Please read the Assembly Instructions prior to assembling the unit. 2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface. 3. Keep all hardware and parts out of reach of children. 4.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Chair Backrest (Qty. 2) B- Seat (Qty. 2) C- Metal Stretcher (Qty. 2) D- Front Leg (Qty. 4) (1) 1/4" x 5/8" Bolt (Qty. 20+1 extra) 4 mm Hex Wrench (Qty. 1) Tools required: Hex wrench (provided).
Assembly Instructions 1 B A 1/4" x 5/8" Bolt (4 used in this step) ① DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts. 1. Unpack the unit and confirm that you have all the hardware and required parts. 2. Lay one Backrest (A) on a smooth and protective surface with the threaded sockets facing up. 3. Attach one Seat (B) to the Backrest (A) with four 5/8" Bolts (1).
Assembly Instructions C 1 1 A 1/4" x 5/8" Bolt (2 used in this step) ① 4. Fasten one Metal Stretcher (C) to the Backrest (A) with two 5/8" Bolts (1).
Assembly Instructions D D D 1 D B C C D B B 1 A 1/4" x 5/8" Bolt (4 used in this step) ① 5. Fit two Front Legs (D) into the front corner tubes on the Seat Frames (B). Fasten the Legs (D) in place with four 5/8" Bolts (1). Securely tighten the bolts with the provided hex wrench. 6. Stand the unit upright. 7. Repeat the same procedure to assemble the other chair.
Care and Maintenance For everyday cleaning, chrome, brass, aluminum, and painted metal surfaces can be kept looking their best by wiping with a slightly damp, soft cotton cloth, or vacuum cleaner brush. If soiled, wipe with clean sponge or cloth wrung out of water. Wipe dry with cloth or paper towel to avoid water spots. Do not use any harsh abrasives or chemicals to clean any metal surfaces as it may damage the protective coating.
LOTE NÚMERO: FECHA DE COMPRA: / / Silla de 2-piezas Collin Serie # BH16-084-399-03 blanca # BH16-084-399-04 verde # BH16-084-399-05 plateada ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda donde lo compró.
MÁXIMA CARGA RECOMENDADA 1. Máximo peso recomendado es 136 kg (300 libras). ESTA UNIDAD DEBE UTILIZARSE CON LOS PRODUCTOS ADECUADOS Y PESOS MÁXIMOS INDICADOS. SI SE UTILIZAN OTROS PRODUCTOS O SE EXEDE EL PESO MÁXIMO, PODRÍA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. INFORMACION GENERAL, RECOMENDACIONES Y TRUCOS 1. Por favor lea el instructivo antes de comenzar el ensamble. 2. Para evitar daños, ensamble la unidad en una area nivelada y libre de abrazivos. 3.
Lista de Partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. A- Respaldo de silla (Cant. 2) B- Asiento de silla (Cant. 2) C- Soporte de metal (Cant. 2) D- Pata frontal (Cant. 4) (1) Tornillo de 1/4" x 5/8" (Cant. 20+1 extra) Llave hexagonal 4 mm (Cant. 1) Herramienta requerida: Llave hexagonal (proveida).
Instrucciones de ensamble 1 B A Tornillo de 1/4" x 5/8" (4 usados en este paso) ① NO APRIETE completamente los tornillos o tuercas hasta que todas las partes esten ensambladas. Para evitar daños a la rosca no apriete demas los tornillos o tuercas. 1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas. 2. Poner el respaldo de silla (A) en una area limpia y libre con los agujeros con insertos hacia arriba. 3.
Instrucciones de ensamble C 1 1 A Tornillo de 1/4" x 5/8" (2 usados en este paso) ① 4. Apretar un soporte de metal (C) al respaldo de silla (A) con dos tornillos de 5/8" (1).
Instrucciones de ensamble D D D 1 D B C C D B B 1 A Tornillo de 1/4" x 5/8" (4 usados en este paso) ① 5. Fijar las dos patas frontales (D) en los tubos de las esquinas frontales del marco del asiento (B). Fijar las patas (D) en su lugar con cuatro tornillos de 5/8" (1). Apriete firmemente los tornillos con la llave hexagonal suministrada. 6. Poner la unidad en posición vertical. 7. Repetir el mismo proceso para ensamblar la otra silla.
Mantenimiento y Cuidados Para una limpieza diaria, las superficies de cromo, bronce, aluminio y de metal pintado se mantienen mejor limpiándolas con un trapo de algodón suave, levemente humedecido, un sacudidor o con el cepillo de la aspiradora. Si hay manchas límpielas con una esponja o con un trapo limpio húmedo (exprimido). Seque completamente con un trapo o una toalla de papel para evitar manchas de agua. No utilice productos abrasivos o químicos fuertes para limpiar las superficies de metal.