LOT NUMBER: DATE PURCHASED: / / Austen 5pc Counter Height Dining Stock # BH16-084-499-03 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Austen 5pc Counter Height Dining MODEL # BH16-084-499-03 MADE IN MALAYSIA MAXIMUM LOAD 181.4 kg / 400 lb. MAXIMUM LOAD 136 kg / 300 lb. THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY. GENERAL INFORMATION, TIPS AND TRICKS 1. Please read the Assembly Instructions prior to assembling the unit.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Table Top (Qty. 1) B- Table Apron (Qty. 4) C- Table Leg (Qty. 4) D- Backrest Left Post (Qty. 4) E- Backrest Right Post (Qty. 4) F- Seat Frame (Qty. 4) G- Footrest (Qty. 4) H- Chair Front Leg (Qty. 8) I- Backrest Slat (Qty. 8) J- Seat Panel (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) 1/4" x 5/8" Bolt (Qty. 92+2 extra) (2) 1/4" x 1-3/4" Bolt (Qty. 32+1 extra) (3) Lock Washer (Qty. 92+2 extra) (5) M6 x 15 mm Wood Screw (Qty. 24+1 extra) (4) Flat Washer (Qty. 92+2 extra) Hex Wrench (Qty. 2) Touch-up Pen (Qty. 1) Tools required: Hex wrench (provided) and Phillips screwdriver (not provided).
Assembly Instructions for Table 1 3 4 B 1 3 4 B B B B B A 1/4" x 5/8" Bolt (12 used in this step) Lock Washer (12 used in this step) ① ③ Flat Washer (12 used in this step) ④ DO NOT fully tighten the bolts initially until all the bolts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the bolts. 1. Unpack the unit and confirm that you have all the hardware and required parts. 2. Position the Table Top (A) upside down on a level and protected surface. 3.
Assembly Instructions for Table C B B 4 4 1 3 C 3 A C C C B B A B B (16 used in this step) Lock Washer (16 used in this step) ① ③ 1/4" x 5/8" Bolt Flat Washer (16 used in this step) ④ 4. Attach four Legs (C) to the Aprons (B) with sixteen 5/8" Bolts (1) and sixteen Washers (3 and 4). 5. Stand the unit upright and place it at the desired location.
Assembly Instructions for Chair 2 I I E 2 D 1/4" x 1-3/4" Bolt (8 used in this step) ② 6. Combine two Backrest Slats (I) between the Backrest Left and Right Posts (D and E) with eight 1-3/4" Bolts (2).
Assembly Instructions for Chair F 1 3 4 G F/G D/E 1 3 4 E D 1/4" x 5/8" Bolt (8 used in this step) Lock Washer (8 used in this step) Flat Washer (8 used in this step) ③ ④ ① 7. Attach the Seat Frame (F) and Footrest (G) to the assembled backrest with eight 5/8" Bolts (1) and eight Washers (3 and 4).
Assembly Instructions for Chair H F H 13 4 H G D/E 4 3 1 1/4" x 5/8" Bolt (8 used in this step) Lock Washer (8 used in this step) Flat Washer (8 used in this step) ③ ④ ① 8. Proceed to attach the two Chair Front Legs (H) to the Seat Frame (F) and Footrest (G) with eight 5/8" Bolts (1) and eight Washers (3 and 4).
Assembly Instructions for Chair 5 F J F J 15 mm Wood Screw (6 used in this step) ⑤ 9. Place one Seat Panel (J) upside down on the carton or other support surface as shown. NOTE: Place a protective cover (like the bubble wrap packing material) over the carton or other support surface to prevent from scratching. 10. Flip the assembled chair frame upside down and fit the Backrest Posts (D and E) into the notches of the Seat Panel (J).
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
LOTE NÚMERO: FECHA DE COMPRA: / / Comedor Austen de 5piezas altura de barra Serie # BH16-084-499-03 ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda en que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m.
PESOS MÁXIMOS RECOMENDADOS FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Comedor Austen de 5piezas altura de barra MODELO # BH16-084-499-03 HECHO EN MALASIA CARGA MÁXIMA 181.4 kg / 400 lb. CARGA MÁXIMA 136 kg / 300 lb. ESTA UNIDAD DEBE UTILIZARSE CON LOS PRODUCTOS ADECUADOS Y PESOS MÁXIMOS INDICADOS. SI SE UTILIZAN OTROS PRODUCTOS O SE EXEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. INFORMACIÓN GENERAL CONSEJOS YTRUCOS 1.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y ferretería antes de iniciar el ensamblado. A- Superficie de tapa (Cant. 1) B- Delantal de tapa (Cant. 4) C- Pata de mesa (Cant. 4) D- Poste izquierdo (Cant. 4) E- Poste derecho (Cant. 4) F- Marco de asiento (Cant. 4) G- Descanso (Cant. 4) H- Pata frontal de silla (Cant. 8) I- Soporte de silla (Cant. 8) J- Panel de silla (Cant.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. (1) Tornillo 1/4" x 5/8" (Cant. 92+2 extra) (2) Tornillo 1/4" x 1-3/4" (Cant. 32+1 extra) (3) Arandela de presión (Cant. 92+2 extra) (4) Arandela plana (Cant. 92+2 extra) (5) Tornillo M6 x 15 mm para madera (Cant. 24+1 extra) Llave hexagonal (Cant. 2) Plumón de retoque (Cant.
Instrucciones de ensamble para mesa 1 3 4 B 1 3 4 B B B B B A Tornillo 1/4" x 5/8" (12 usados en este paso) Arandela de presión (12 usados en este paso) ① Arandela plana (12 usados en este paso) ③ ④ NO APRETAR completamente los tornillos al comenzar, hasta que todos los tornillos esten listos para el ensamble. Para evitar daños a las roscas, NO APRETAR demasiado. 1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas. 2.
Instrucciones de ensamble para mesa C B B 4 4 1 3 C 3 1 A C C C B B A B B Tornillo 1/4" x 5/8" (16 usados en este paso) Arandela de presión (16 usados en este paso) ① ③ Arandela plana (16 usados en este paso) ④ 4. Adjuntar las cuatro patas de mesa (C) a los delantales de mesa (B) con dieciséis tornillos de 5/8" (1) y dieciséis arandelas (3 y 4). 5. Poner la unidad en posición vertical y colocar en su lugar deseado.
Instrucciones de ensamble para silla 2 I I E 2 D Tornillo 1/4" x 1-3/4" (8 usados en este paso) ② 6. Combinar dos soportes de silla (I) entre los postes izquierdo y derecho (D y E) con ocho tornillos de 1 3/4" (2).
Instrucciones de ensamble para silla F 1 3 4 G F/G D/E 1 3 4 E D Tornillo 1/4" x 5/8" (8 usados en este paso) Arandela de presión (8 usados en este paso) ① ③ Arandela plana (8 usados en este paso) ④ 7. Fije el marco del asiento (F) y el descanso (G) al respaldo ensamblado con ocho tornillos de 5/8" (1) y ocho arandelas (3 y 4).
Instrucciones de ensamble para silla H F H 13 4 H G D/E 4 3 1 Tornillo 1/4" x 5/8" (8 usados en este paso) Arandela de presión (8 usados en este paso) ① ③ Arandela plana (8 usados en este paso) ④ 8. Proceder para unir las dos patas frontales de silla (H) al marco del asiento (F) y el descanso (G) con ocho tornillos de 5/8" (1) y ocho arandelas (3 y 4).
Instrucciones de ensamble para silla 5 F J F J Tornillo de 15 mm para madera (6 usados en este paso) ⑤ 9. Colocar un panel de la silla (J) boca abajo en la caja de cartón u otra superficie de soporte tal como se muestra. NOTA: Coloque una cubierta protectora (como el material de empaque de plástico de burbujas) a través de la caja de cartón u otra superficie de soporte para evitar que se talle o dañe. 10.
Mantenimiento y cuidados Use una toalla suave y limpia para evitar daños y rayaduras. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.