REED CONSOLE TABLE Assembly Instructions pecan model# BH16-021-199-14 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Manufactured By: Customer Service: BDDMI 1.877.436.7290 1321 Tyler St NE, Minneapolis, MN 55413 customersupport@tenspringstreet.
TOOLS NEEDED Flat Head Screwdriver Phillips Head Screwdriver PARTS LIST TOP PANEL SIDE ASSEMBLY [X2] B O T T O M PA N E L RAIL [X4] A B C D Before you begin: 1. Check for damaged or missing parts. 2. Use the carton as a working surface to prevent product damage during assembly.
HARDWARE LIST 1. D o w e l x8 2. B o l t x12 3. W a s h e r x4 4. L o c k W a s h e r x4 5. A l l e n W r e n c h x1 6. C a m B o l t x4 7. C a m x4 CAUTION: 1. Make sure the screws go through the pre-drilled holes properly. 2. Do not over tighten bolts.
HOW TO USE THE CAM LOCK SYSTEM 3 4 5 180º 4
STEP 1 x4 x4 x4 1. W o o d Dowel 6. C a m B o l t 7. C a m 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush. 3. Refer to page 4 for instructions on how to use the cam lock system.
STEP 2 x4 1. W o o d Dowel x4 x4 x4 x1 2. B o l t 3. W a s h e r 4. L o c k Washer 5. A l l e n Wrench 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Make sure the bolts go through pre-drilled holes properly. 3. Do not over tighten bolts.
STEP 3 x8 x1 2. B o l t 5. A l l e n Wrench 1. Make sure the bolts go through pre-drilled holes properly. 2. Do not over tighten bolts.
! WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: • Install tip-over restraint provided. • Place heaviest items in the lowest drawers. • Do not set TV’s or other heavy objects on top of this product, unless the product is specifically designed to accommodate them. • Never allow children to climb or hang on drawers, doors, or shelves. • Never open more than one drawer at a time. (OR) • Do not defeat or remove the drawer interlock system.
CONSOLA REED Instrucciones de Ensamble nuez model# BH16-021-199-14 ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD. POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA. Fabricado Por : Servicio al Cliente: BDDMI 1.877.436.7290 1321 Tyler St NE, Minneapolis, MN 55413 customersupport@tenspringstreet.
HERRAMIENTAS NECESARIAS Destornillador de Cabeza Plana Destornillador Phillips LISTA DE PARTES PA N E L S U P E R I O R ENSAMBLE DEL LADO [X2] PA N E L I N F E R I O R RIEL [X4] A B C D Antes de comenzar: 1. Compruebe si hay piezas dañadas o faltantes. 2. Utilice la caja de cartón como superficie de trabajo para evitar daños al producto durante el montaje.
LISTA DE ARTÍCULOS DE FERRETERÍA 1. C l a v i j a d e Madera x8 2. P e r n o x12 3. A r a n d e l a x4 4. Arandela Fijadora x4 5. L l a v a A l l e n x1 6. To r n i l l o d e L e v a x4 7. L e v a x4 PRECAUCIÓN: 1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada. 2. No sobreapriete los tornillos.
COMO USAR EL SISTEMA FIJADOR DE LEVA 3 4 5 180º 4
PASO 1 x4 x4 x4 1. C l a v i j a d e Maderat 2. To r n i l l o d e Leva 7. L e v a 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2. Los tornillos de leva deben de estar atornillados al ras. 3. Refiérase a la página 4 para instrucciones para como usar el sistema de levas.
PASO 2 x4 x4 1. C l a v i j a d e 2. P e r n o Madera x4 x4 3. A r a n d e l a 4. A r a n d e l a Fijadora x1 5. L l a v a Allen 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2.Cerciórese que los pernos tornillos pasen por los agujeros pretaladrados de manera apropiada. 3. No sobreapriete los pernos tornillos.
PASO 3 x8 x1 2. P e r n o 5. L l a v a Allen 1.Cerciórese que los pernos tornillos pasen por los agujeros pretaladrados de manera apropiada. 2. No sobreapriete los pernos tornillos.
! ADVERTENCIA Lesiones por aplastamiento graves o fatales pueden ocurrir debido a la caida el mueble. Para prevenir la caida: - Instalar los sujetadores contra caídas proporcionada. - Coloque los artículos más pesados en las repisas. inferiores o cajones inferiores y lo más atrás posible. - A menos de que esté especifícamente diseñado para acomodarlo, no coloque televisores u otro objeto pesado sobre este producto. - Nunca permita que los niños se suban o cuelguen sobre los cajones, puertas o repisas.