BEDFORD COFFEE TABLE Assembly Instructions gray model# BH17-021-399-04 ivory model# BH17-021-399-03 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Manufactured By: Customer Service: BDDMI 1.877.436.7290 1321 Tyler St NE, Minneapolis, MN 55413 customersupport@tenspringstreet.
TOOLS NEEDED Flat Head Screwdriver Phillips Head Screwdriver PARTS LIST TOP PANEL SIDE ASSEMBLY [X2] B O T T O M PA N E L BOT TOM RAIL [ X2] TOP RAIL [ X2] A B C D E Before you begin: 1. Check for damaged or missing parts. 2. Use the carton as a working surface to prevent product damage during assembly.
HARDWARE LIST 1. Wood D owel x28 2. Cam Bolt x16 3. Cam x16 4. M6x32mm Bolt x4 5. Lock Washer x4 6. Washer x4 CAUTION: 1. Make sure the screws go through the pre-drilled holes properly. 2. Do not over tighten bolts.
HARDWARE LIST 7. Allen Wrench x1 8. Angle Iron x4 9. 15mm Pan Head Screw x12 CAUTION: 1. Make sure the screws go through the pre-drilled holes properly. 2. Do not over tighten bolts.
HOW TO USE THE CAM LOCK SYSTEM 1 3 2 4 5 180º 5
STEP 1 x6 x4 x4 1. Wood Dowel 2. Cam Bolt 3. Cam NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE. 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush. 3. Refer to page 5 for instructions on how to use the cam lock system.
STEP 2 x4 x2 x2 1. Wood Dowel 2. Cam Bolt 3. Cam NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE. 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush. 3. Refer to page 5 for instructions on how to use the cam lock system.
STEP 3 x2 x2 x2 1. Wood Dowel 2. Cam Bolt 3. Cam NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE. 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush. 3. Refer to page 5 for instructions on how to use the cam lock system.
STEP 4 x6 x4 x4 1. Wood Dowel 2. Cam Bolt 3. Cam NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE. 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush. 3. Refer to page 5 for instructions on how to use the cam lock system.
STEP 5 x10 x4 x4 x1 1. Wood Dowel 2. Cam Bolt 3. Cam 7. Allen Wrench x4 x4 x4 4. M6x32mm Bolt 5. Lock Washer 6. Washer NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE. 1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out. 2. Screw-In cam bolts must be screwed down flush. 3. Refer to page 5 for instructions on how to use the cam lock system.
STEP 6 x12 x4 9. 15mm Pan 8. Angle Iron Head Screw NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE. 1. Make sure the screws go through pre-drilled holes properly. 2. Do not over tighten screws.
Furniture Care Instructions: Dust with clean, lint-free cloth. Use furniture spray polish as needed. Customer Service: 877.436.7290 customersupport@tenspringstreet.com 70 / s. lb .5 31 . kg 50 / s. lb .7 22 . kg Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the highest quality of standards.
MESA PARA CAFÉ BEDFORD Instrucciones de Ensamble gris model# BH17-021-399-04 marfil model# BH17-021-399-03 ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD. POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA. Fabricado Por : Servicio al Cliente: BDDMI 1.877.436.7290 1321 Tyler St NE, Minneapolis, MN 55413 customersupport@tenspringstreet.
HERRAMIENTAS NECESARIAS Destornillador de Cabeza Plana Destornillador Phillips LISTA DE PARTES PA N E L S U P E R I O R ENSAMBLE DEL LADO [X2] PA N E L I N F E R I O R RIEL INFERIOR [X2] RIEL SUPERIOR [X2] A B C D E Antes de comenzar: 1. Compruebe si hay piezas dañadas o faltantes. 2. Utilice la caja de cartón como superficie de trabajo para evitar daños al producto durante el montaje.
LISTA DE ARTÍCULOS DE FERRETERÍA 1. Clavija de Madera x28 2 . To r n i l l o d e L e v a x16 3. Leva x16 4. M6x32mm Perno x4 5. Arandela Fijodora x4 6. Arandela x4 PRECAUCIÓN: 1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada. 2. No sobreapriete los tornillos.
LISTA DE ARTÍCULOS DE FERRETERÍA 7. Llava Allen x1 8. Soporte x4 9 . 1 5 m m To r n i l l o d e Cabeza de Noria x12 PRECAUCIÓN: 1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada. 2. No sobreapriete los tornillos.
COMO USAR EL SISTEMA FIJADOR DE LEVA 1 3 2 4 5 180º 5
PASO 1 x6 x4 x4 1. Clavija de Madera 2 . To r n i l l o de Leva 3. Leva NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL. 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2. Los tornillos de leva deben de estar atornillados al ras. 3. Refiérase a la página 5 para instrucciones para como usar el sistema de levas.
PASO 2 x4 x2 x2 1. Clavija de Madera 2 . To r n i l l o de Leva 3. Leva NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL. 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2. Los tornillos de leva deben de estar atornillados al ras. 3. Refiérase a la página 5 para instrucciones para como usar el sistema de levas.
PASO 3 x2 x2 x2 1. Clavija de Madera 2 . To r n i l l o de Leva 3. Leva NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL. 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2. Los tornillos de leva deben de estar atornillados al ras. 3. Refiérase a la página 5 para instrucciones para como usar el sistema de levas.
PASO 4 x6 x4 x4 1. Clavija de Madera 2 . To r n i l l o de Leva 3. Leva NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL. 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2. Los tornillos de leva deben de estar atornillados al ras. 3. Refiérase a la página 5 para instrucciones para como usar el sistema de levas.
PASO 5 x10 x4 1 . C l a v i j a d e 2 . To r n i l l o Madera de Leva x4 x4 x1 3. Leva 7. Llava Allen x4 x4 4. M6x32mm 5. Arandela Perno Fijodora 6. Arandela NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL. 1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas. 2. Los tornillos de leva deben de estar atornillados al ras. 3. Refiérase a la página 5 para instrucciones para como usar el sistema de levas.
PASO 6 x12 x4 9. 15mm To r n i l l o d e Cabeza de Noria 8. Soporte NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL. 1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada. 2. No sobreapriete los tornillos.
Instrucciones de cuidado: Desempolve con un paño limpio y libre de pelusa. Utilice un pulidor en spray para muebles según se necesite. Servicio al Cliente: 877.436.7290 customersupport@tenspringstreet.com 70 / s. lb .5 31 . kg 50 / s. lb .7 22 . kg Su completa satisfacción es nuestra prioridad número 1. Nuestro producto está diseñado y fabricado para cumplir con la más alta calidad de las normas.