8 CUBE STORAGE ORGANIZER WITH METAL BASE VENDOR STOCK NUMBERS BHAJI-084-098-03 ESPRESSO BHAJI-084-098-06 RUSTIC GRAY BHAJI-084-098-09 WHITE BHAJI-084-099-35 VINTAGE WALNUT TOP PANEL MAXIMUM LOAD 100 LB (45.5 KG}) EACH CUBE MAXIMUM LOAD 30 LB {13.6 KG) RECOMMENDED NUMBER OF PEOPLE FOR ASSEMBLY : 1 ESTIMATED ASSEMBLY TIME: 1 HOUR . CALL OUR TOLL FREE NUMBER 1-800-729-1569 FOR FURTHER ASSISTANCE. . ADDITIONAL PARTS ARE AVAILABLE FOR A FEE.
8 CUBE STORAGE ORGANIZER WITH METAL BASE VENDOR STOCK NUMBERS BHAJI-084-098-03 ESPRESSO BHAJI-084-098-06 RUSTIC GRAY BHAJI-084-098-09 WHITE BHAJI-084-099-35 VINTAGE WALNUT & BEFORE STARTING TOOLS NEEDED TO ASSEMBLE . Read and understand all the steps carefully before starting. If each step is not followed in the correct order the assembly will be difficult and may result in damages. . Work in a spacious area, preferably on a carpeted surface, near where the unit will be used. .
VENDOR STOCK NUMBERS BHAJI-084-098-03 ESPRESSO 8 CUBE STORAGE ORGANIZER WITH METAL BASE BHAJI-084-098-06 RUSTIC GRAY BHAJI-084-098-09 WHITE BHAJI-084-099-35 VINTAGE WALNUT N Top panel Bottom panel Side panel (Qty: 1) (Qty:1) (Qty: 2) Middle shelf @ Partition board 1 @ Partition board 2 (Qty: 1) (Qty: 4) % {Qty: 2) Metal tube Metal feet (Qty: 2) (Qty: 2) We are available to assist you Monday -Friday from 9:00 am 5:00 pm Eastern Standard Time. VERIFY THAT ALL PARTS ARE LISTED BEFORE BEGINNING USA only.
VENDOR STOCK NUMBERS ESPRESSO 8 CUBE STORAGE ORGANIZER WITH METAL BASE BHAJI-084-098-06 RUSTIC GRAY BHAJI-084-098-09 WHITE BHAJI-084-099-35 VINTAGE WALNUT @ @ ‘ Screw bolt Washer Qty: 4 Qty: 4 ® @ Cam lock Wood dowel 1 Wood dowel 2 Safety strap kit Glue Qty: 16 Qty: 24+1 Extra Qty: 1 Qty: 1 @ Allen key Qty: 1 Qty: 12 We are available to assist you Monday -Friday from 9:00 am 5:00 pm Eastern Standard Time. VERIFY THAT ALL PARTS ARE LISTED BEFORE BEGINNING 1-800-729-1569 USA only.
8 CUBE STORAGE ORGANIZER WITH METAL BASE VENDOR STOCK NUMBERS BHAJI-084-098-03 ESPRESSO BHAJI-084-098-06 RUSTIC GRAY BHAJI-084-098-09 WHITE BHAJI-084-099-35 VINTAGE WALNUT CAM FASTENING SYSTEM Screw the cam bolt into the prevailed panel. The screw should be tightened so no threads are visible. The larger ring of the cam should touch the panel. Insert the cam lock into the prevailed hole in the panel. The plus and minus signs should be facing the outside of the panel.
Insert PCs wood dowel @ & PCs wood dowel ® into two part E1 (partition board 1}. | Insert apes wood dowel & into one part F (partition board 2}, Insert PCs wood dowel @ & PCs wood dowel ® into one part F {partition board 2). Place dowel on hole.Gently tap with hammer to insert. 1 Insert PCs wood dowel & inch two part E1 {partition board 1). ®8 Warning ! Additional glue for step 1. Glue need to be put into the hole before insert the wood dowel.
: ! Resew in the cam bolts into part Warning ! Additional glue for step 2. Glue need to be put into the hole before insert the wood dowel.
Insert 2 pcs wood dowel in each side, Screw in the cam bolts into 2 sides of part D as shown. ® Opposite Warning ! Additional glue for step 3. Glue need 1o be put into the hole before insert the wood dowel.
Align and attach part F fo the shelf. Align and attach part C1 to the structure and then tighten the cam locks.
Assemble the metal base with attached Allen key as shown. Screw bolt Attach the metal base to the bottom of the part B1 then insert the screw and frighten it.
1 1 Now Your Unit Is Completed Ho|§\ Option: 2 Option: 1 Fasten the safety strap to the wall using OPTION shown. Option 1: Fasten the strap (9a) fo a stud in the wall using the screw {9d) through washer (9b). Option 2: Drill a 3/16" diameter hole in the wallboard. Tap the wall anchor{e) info the hole unfit it is flush. Fasten the strap {9a) to the wall anchor (Fe) swing the screw (9d) through the washer (9b).
ORGANIZADOR DE ALMACENAMIENTO DE 8 CUBOS CON BASE DE METAL MOMERO DE STOCK DEL VENDEDOR BHUTAN-084-098-03 CAFÉ EXPRÉS BHUTAN-084-098-06 GRIS RUSTICO BHUTAN-084-098-09 BLANCO BHUTAN-084-099-35 MESA NOGAL DE VENDIMIA A ANTES DE COMENZAR HERRAMIENTAS NECESARIAS PARA ENSAMBLAR . Leer y entender todos los pasos cuidadosamente antes de comenzar. si no se sigue cada paso en el orden correcto, el montaje ser difícil y puede ocasionar dacios. .
NUMERO DE STOCK DEL VENDEDOR ORGANIZADOR DE ALMACENAMIENTO DE 8 CUBOS CON BASE DE METAL BHUTAN-084-098-09 BLANCO BHUTAN-084-099-35 MESA NOGAL DE VENDIMIA == Barra arriba Badajo Barra lateral (Cantidad: 1) {Cantidad: 1) {Cantidad: 2} N\ Estante del medio Tabla de tabique 1 Tabla de tabique 2 {Cantidad: 1) @ {Cantidad: 4) @ fi {Cantidad: 2) Tubo metílico Pies de metal ({Cantidad: 2) {Cantidad: 2) Estamos disponibles para ayudarla de Lunes Viernes VERIFIQUE QUE TODAS LAS PIEZAS ESTÉN EN LA LISTA ANTES de 9:00 a
NUMERO DE STOCK DEL VENDEDOR BHUTAN-084-098-03 CAFÉ EXPRÉS ORGANIZADOR DE ALMACENAMIENTO DE 8 CAFÉ EXPRÉS CUBOS CON BASE DE METAL BLANCO BHUTAN-084-099-35 MESA NOGAL DE VENDIMIA Tomillo Arandela Tomillo 1 Tornillo 2 Tomillo de combadura Cantidad: 4 Cantidad: 4 Cantidad: 4 Cantidad: 8 Cantidad: Cerrojo de combadura Clavija de madera 1 Clavija de madera 2 Cinturón Pegamento Cantidad: 16 Cantidad: 6 Cantidad: 24+1 Extra Cantidad: 1 Cantidad: 1 ) Lave alelen Tapen Cantidad: 1 Cantidad: 12 Estamos disponibles pa
ORGANIZADOR DE ALMACENAMIENTO DE 8 CUBOS CON BASE DE METAL MOMERO DE STOCK DEL VENDEDOR BHUTAN-084-098-03 CAFÉ EXPRÉS BHUTAN-084-098-06 GRIS RUSTICO BHUTAN-084-098-09 BLANCO BHUTAN-084-099-35 MESA NOGAL DE VENDIMIA SISTEMA DE FIJACIÓN CAM Atornille el Tornillo de combadura en el panel taladrador. El tornillo debe apretarse para que no haya roscas visibles, El anillo mas grande del cam debe tocar el panel. Inserte el Cerrojo de combadura en el agujero pre taladrado en el panel.
Inserte 2 piezas de pasador de madera en dos partes E1 (tablero de separación 1). Inserte 2 piezas de espiga de madera @ y 2 piezas de espiga de madera ® en dos partes E1 (tablero de separación 1). Inserte 2 piezas de espiga de madera ® en una parte F (tablero de separación 2) Inserte 2 piezas de la clavija de madera @ y pes clavija de madera @ en una parte F {tabla de partición 2). Coloque la clavija en el orificio. Golpee suavemente con el martillo para insertar.
: ! Atornille los pernos de leva en la parte advertencia! Pegamento adicional para el paso 2. El pegamento debe colocarse en el soporte antes de insertar el tarugo de madera.
Atornille los pernos de leva en 2 lados de la parte D como se muestra, 3 Inserte 2 piezas de la clavija de madera ® en cada lado. advertencia Pegamento adicional para el paso 3. El pegamento debe colocarse en el soporte antes de insertar el tarugo de madera.
Alinee y fije la parte C1 a la estructura y luego apriete las cerraduras de leva.
Alinee y file la parte estructura y luego apriete las cerraduras de leva.
Monte la base de metal con la llave alelen como se muestra. Tornillo Arandela Filie la base de metal a la parte inferior de la parte B1, luego inserte el tornillo y apriételo. Fije la correa de seguridad en la parte A como se muestra.
11 (@B x1) Arancel Ahora Tu Unidad Esta Compuesta. Tornillo Ancla de pared Agujero Opción Opción Abrochar el cinturón con la pared usando OPCIÓN 1 o 2 como ilustrado. Opción 1: Abrochar el CINTURÓN (9a) con el clavo en la pared usando tornillo {9d) a través de arancel (9b). Opción 2: Perforar un agujero de diámetro 3/16"" en la barra. Espitar la ancla de pared (9€) en el agujera hasta que es quede al mismo nivel.