LOT NUMBER: DATE PURCHASED: / / Loft Storage Bed Stock # BH17-084-097-45 Gray # BH17-084-098-45 Mocha # BH17-084-098-46 White ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT ENTRAPMENT BETWEEN THE BED AND WALL. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts, and jump ropes. Prohibit more than one person on upper bunk.
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT OR FALLS • Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. • Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls. • Surface of mattress must be at least 5 in. (12.70 cm) below the upper edge of guardrails. • Do not allow children under 6 years of age to use the upper bunk.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Mattress Side Rail (Qty. 2) D- Headboard Front Post (Qty. 1) B- Guardrail (Qty. 4) C- Ventilated Shelf (Qty. 2) E- Headboard Back Post (Qty. 1) F- Footboard Front Post (Qty. 1) G- Footboard Back Post (Qty. 1) H- Headboard Top Rail (Qty. 2) I- Headboard Middle Rail (Qty. 1) J- Headboard Bottom Rail (Qty. 1) K- Headboard Support (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. P- Left Ladder Support (Qty. 1) S- Guardrail Support (Qty. 2) Q- Right Ladder Support (Qty. 1) R- Ladder Step (Qty. 3) T- Shelf Support (Qty. 1) U- Mattress Support Slats (Qty. 1) (1) 1/4” x 100 mm Bolt (Qty. 8+1 extra) (2) 1/4” x 32 mm Bolt (Qty. 20+1 extra) (3) 6.5 mm x 100 mm Tapping Bolt (Qty. 22+1 extra) (5) M10 x 50 mm Wood Dowel (Qty.
ASSEMBLY OF THE HEADBOARD E H H I J D 5 3 6.5 mm x 100 mm Tapping Bolt (8 used in this step) ③ M10 x 50 mm Wood Dowel (10 used in this step) ⑤ 1. Unpack the units and confirm that you have all hardware and required parts. 2. Insert the Wood Dowels (5) into the both end holes on the Headboard Rails (H, I and J) as a guide and attach the Headboard Front Post (D) to the Rails with four 100 mm Tapping Bolts (3). 3. Repeat the same procedure to attach the Headboard Back Post (E) at the opposite end.
ASSEMBLY OF THE HEADBOARD 2 E UP I K J D 1/4” x 32 mm Bolt (4 used in this step) ② 4. Attach the Headboard Support (K) to the Rails (I and J) with four 32 mm Bolts (2).
ASSEMBLY OF THE LADDER 5 Q R 5 R R R P 4 6.5 mm x 48 mm Bolt (6 used in this step) M10 x 50 mm Wood Dowel (6 used in this step) ④ ⑤ 5. Insert the 50 mm Wood Dowels (5) into the large holes of Ladder Steps (R) at both ends. Attach Left and Right Ladder Supports (P and Q) to the Ladder Steps (R) using the 48 mm Tapping Bolts (4).
ASSEMBLY OF THE FOOTBOARD F M N G 5 3 6.5 mm x 100 mm Tapping Bolt (4 used in this step) ③ M10 x 50 mm Wood Dowel (6 used in this step) ⑤ 6. Insert the Wood Dowels (5) into the both end holes on the Footboard Rails (M and N) as a guide and attach the Footboard Front Post (F) to the Rails with two 100 mm Tapping Bolts (3). 7. Repeat the same procedure to attach the Footboard Back Post (G) at the opposite end.
ASSEMBLY OF THE FOOTBOARD P Q M F G 4 N 6.5 mm x 48 mm Tapping Bolt (4 used in this step) ④ 8. Attach the assembly of the ladder to the Rails (M and N) with four 48 mm Tapping Bolts (4).
ASSEMBLY OF THE FOOTBOARD L L M F G 3 5 6.5 mm x 100 mm Tapping Bolt (2 used in this step) ③ M10 x 50 mm Wood Dowel (2 used in this step) ⑤ 9. Combine the Footboard Top Rails (L) with the Footboard Back Post (G) together with two 50 mm Wood Dowels (5) and two 100 mm Tapping Bolts (3).
ASSEMBLY OF THE FOOTBOARD Q L L 4 M F G 6.5 mm x 48 mm Tapping Bolt (2 used in this step) ④ 10. Fasten the Footboard Top Rails (L) in place with two 48 mm Tapping Bolts (4).
ASSEMBLY OF THE FOOTBOARD M F G UP N O 2 1/4” x 32 mm Bolt (4 used in this step) ② 11. Attach the Footboard Support (O) to the Rails (M and N) with four 32 mm Bolts (2).
Assembly Instructions G O F C C 5 2 1/4” x 32 mm Bolt (4 used in this step) M10 x 50 mm Wood Dowel (4 used in this step) ② ⑤ 12. Attach two Ventilated Shelves (C) to the Footboard Support (O) and Front Post (F) with four 32 mm Bolts (2) and four 50 mm Wood Dowels (5).
Assembly Instructions 7 1 A G C C F 1/4” x 100 mm Bolt (2 used in this step) ① Barrel Nut (2 used in this step) ⑦ 13. Insert two Barrel Nuts (7) into the end of one Mattress Side Rail (A). 14. Attach the Mattress Side Rail (A) to the Footboard Front Post (F) using two 100 mm Bolts (1) through the drilled holes on the posts and screw into the Barrel Nuts (7).
Assembly Instructions 5 3 B B G C C F 6.5 mm x 100 mm Tapping Bolt (2 used in this step) ③ M10 x 50 mm Wood Dowel (2 used in this step) ⑤ 15. Attach two Guardrails (B) to the Footboard Front Post (F) with two 100 mm Tapping Bolts (3) and two 50 mm Wood Dowels (5).
Assembly Instructions Barrel Nut (6 used in this step) ⑦ 1 5 E B 3 I B A A J B K 7 D B B G B A C C F 5 1/4” x 100 mm Bolt (6 used in this step) ① 2 1/4” x 32 mm Bolt (4 used in this step) ② 6.5 mm x 100 mm Tapping Bolt (6 used in this step) ③ M10 x 50 mm Wood Dowel (10 used in this step) ⑤ 16. Repeat steps 13 through 14 to attach the other Mattress Side Rail (A) to the Footboard Back Post (G). 17.
Assembly Instructions 2 UP T C C 1/4” x 32 mm Bolt (4 used in this step) ② 19. Attach the Shelf Support (T) to the Ventilated Shelves (C) with four 32 mm Bolts (2).
Assembly Instructions UP S B B A B B A UP 6 S UP 4 mm x 30 mm Screw (6 used in this step) ⑥ 20. With the pilot holes as a guide, align and attach the Guardrail Supports (S) to the center of both Guardrails (B) and the Mattress Side Rails (A) with 30 mm Screws (6).
Assembly Instructions 6 A U A 4 mm x 35 mm Screw (14 used in this step) ⑧ 21. Lay out the Mattress Support Slats (U) onto the strips on the Mattress Side Rails (A). Make sure that the end slats located close to the Posts. Insert and screw the 35 mm Screws (8) into the countersunk holes on each slat. Tighten the screws using a Phillips screwdriver.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently.
NÚMERO de LOTE: FECHA de COMPRA: / / Litera con area de almacenamiento Serie # BH17-084-097-45 Gris # BH17-084-098-45 Moca # BH17-084-098-46 Blanco ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compró.
SIEMPRE USAR LOS RIELES DE SEGURIDAD EN LOS 2 LADOS LARGOS DE LA LITERA SUPERIOR. SI LA LITERA SERA PUESTA CONTRA LA PARED, EL RIEL QUE CORRE LA LONGITUD COMPLETA DE LA LITERA DEBERA SER PUESTA CONTRA LA PARED PARA PREVENIR SER ATASCADO ENTRE LA LITERA Y LA PARED. PELIGRO DE ESTRANGULACIÓN – Nunca adjuntar o colgar articulos a cualquier parte de la litera que no esten diseñados pa usarse con la litera; por ejemplo, pero no limitado a, garfios, cinturones, y cuerdas para saltar.
PARA AYUDAR A PREVENIR LESIONES SERIAS O FATALES POR ATASCAMIENTO O CAIDAS • Siga la información en los avisos que aparecen en la estructura extrema de la litera superior y en el cartón. No retirar los avisos de la cama. • Siempre usar el colchón del tamaño recomendado ó el soporte del colchón, ó ambos, para ayudar a prevenir la posibilidad de atascamientos o caidas. • La superficie del colchón debe de estar al menos 5 in. (12.70 cm) abajo del borde superior del riel de seguridad.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. A- Riel lateral del colchón (Cant. 2) D- Poste frontal de cabecera (Cant. 1) G- Poste posterior de la piecera (Cant. 1) J- Riel inferior de cabecera (Cant. 1) M- Riel medio de la piecera (Cant. 1) B- Riel de seguridad (Cant. 4) E- Poste posterior de cabecera (Cant. 1) H- Riel superior de cabecera (Cant. 2) K- Soporte de cabecera (Cant.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. P- Soporte de escalera izquierdo (Cant. 1) S- Soporte del riel de seguridad (Cant. 2) Q- Soporte de escalera derecho (Cant. 1) T- Soporte de repisa (Cant. 1) U- Soporte del colchón (Cant. 1) (1) Tornillo de 1/4” x 100 mm (Cant. 8+1 extra) (2) Tornillo de 1/4” x 32 mm (Cant. 20+1 extra) (3) Tornillo de rosca de 6.5 mm x 100 mm (Cant.
ENSAMBLE DE LA CABECERA E H H I J D 5 3 Tornillo de rosca de 6.5 mm x 100 mm (8 usados en este paso) ③ Perno de madera de M10 x 50 mm (10 usados en este paso) ⑤ 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. 2. Insertar los pernos de madera (5) en ambos agujeros finales de los rieles de la cabecera (H, I y J) como guía y adjuntar el poste frontal de la cabecera (D) a los rieles con 4 tornillos de rosca de 100 mm (3). 3.
ENSAMBLE DE LA CABECERA 2 E UP I K J D Tornillo de 1/4” x 32 mm (4 usados en este paso) ② 4. Adjuntar el soporte de cabecera (K) a los rieles (I y J) con 4 tornillos de 32 mm (2).
ENSAMBLE DE LA ESCALERA 5 Q R 5 R R R P 4 Tornillo de 6.5 mm x 48 mm (6 usados en este paso) Perno de madera de M10 x 50 mm (6 usados en este paso) ④ ⑤ 5. Insertar los pernos de madera de 50 mm (5) en los agujeros grandes de los escalones (R) en ambos lados. Adjuntar los soportes de escalera (P y Q) a los escalones (R) usando los tornillos de rosca de 48 mm (4).
ENSAMBLE DE LA PIECERA F M N G 5 3 Tornillo de rosca de 6.5 mm x 100 mm (4 usados en este paso) ③ Perno de madera de M10 x 50 mm (6 usados en este paso) ⑤ 6. Insertar los pernos de madera (5) en ambos agujeros finales de los rieles de piecera (M y N) como guía y adjuntar el poste frontal de la piecera (F) a los rieles con 2 tornillos de rosca de 100 mm (3). 7. Repetir el mismo procedimiento para adjuntar el poste posterior de la piecera (G) al lado opuesto.
ENSAMBLE DE LA PIECERA P Q M F G 4 N Tornillo de rosca de 6.5 mm x 48 mm (4 usados en este paso) ④ 8. Adjuntar la escalera ensamblada a los rieles (M y N) con 4 tornillos de rosca de 48 mm (4).
ENSAMBLE DE LA PIECERA L L M F G 3 5 Tornillo de rosca de 6.5 mm x 100 mm (2 usados en este paso) ③ Perno de madera de M10 x 50 mm (2 usados en este paso) ⑤ 9. Combinar los rieles superiores de la piecera (L) con el poste posterior de la piecera (G) con 2 pernos de madera de 50 mm (5) y 2 tornillos de rosca de 100 mm (3).
ENSAMBLE DE LA PIECERA Q L L 4 M F G Tornillo de rosca de 6.5 mm x 48 mm (2 usados en este paso) ④ 10. Sujetar los rieles superiores de la piecera (L) en su lugar con 2 tornillos de rosca de 48 mm (4).
ENSAMBLE DE LA PIECERA M F G UP N O 2 Tornillo de 1/4” x 32 mm (4 usados en este paso) ② 11. Adjuntar el soporte de la piecera (O) a los rieles (M y N) con 4 tornillos de 32 mm (2).
Instructivo de ensamble G O F C C 5 2 Tornillo de 1/4” x 32 mm (4 usados en este paso) Perno de madera de M10 x 50 mm (4 usados en este paso) ② ⑤ 12. Adjuntar 2 repisas ventilados (C) al soporte de la piecera (O) y al poste frontal de la piecera (F) con 4 tornillos de 32 mm (2) y con 4 pernos de madera de 50 mm (5).
Instructivo de ensamble 7 1 A G C C F Tornillo de 1/4” x 100 mm (2 usados en este paso) ① Tuerca barril (2 usados en este paso) ⑦ 13. Insertar 2 tuercas barril (7) en el extremo du uno de los rieles laterales del colchón (A). 14. Adjuntar el riel lateral del colchón (A) al poste frontal de la piecera (F) usando 2 tornillos de 100 mm (1) a través de los agujeros perforados en los postes y atornillar en las tuercas barril (7).
Instructivo de ensamble 5 3 B B G C C F Tornillo de rosca de 6.5 mm x 100 mm (2 usados en este paso) ③ Perno de madera de M10 x 50 mm (2 usados en este paso) ⑤ 15. Adjuntar 2 rieles de seguridad (B) al poste frontal de la piecera (F) con 2 tornillos de rosca de 100 mm (3) y 2 pernos de madera de 50 mm (5).
Instructivo de ensamble Tuerca barril (6 usados en este paso) ⑦ 1 5 E B 3 I B A A J B K 7 D B B G B A C C F 5 Tornillo de 1/4” x 100 mm (6 usados en este paso) ① 2 Tornillo de 1/4” x 32 mm (4 usados en este paso) ② Tornillo de rosca de 6.5 mm x 100 mm (6 usados en este paso) ③ Perno de madera de M10 x 50 mm (10 usados en este paso) ⑤ 16. Repetir los pasos 13 y 14 para adjuntar el otro riel lateral del colchón (A) al poste posterior de la piecera (G). 17.
Instructivo de ensamble 2 UP T C C Tornillo de 1/4” x 32 mm (4 usados en este paso) ② 19. Adjuntar el soporte de repisa (T) a los repisas ventilados (C) con 4 tornillos de 32 mm (2).
Instructivo de ensamble UP S B B A B B A UP 6 S UP Tornillo de 4 mm x 30 mm (6 usados en este paso) ⑥ 20. Usando los agujeros pilotos como guía, alinear y adjuntar los soportes del riel de seguridad (S) al centro de ambos rieles de seguridad (B) y a los rieles laterales del colchón (A) con tornillos de 30 mm (6).
Instructivo de ensamble 6 A U A Tornillo de 4 mm x 35 mm (14 usados en este paso) ⑧ 21. Descansar los soportes del colchón (U) en las tiras de los rieles laterales del colchón (A). Asegurar de que los soportes extremos esten cerca a los postes. Insertar y fijar los tornillos de 35 mm (8) en los agujeros avellanados en cada soporte. Apretar los tornillos usando el desarmador estrella.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera, pruebela en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los ponga sobre la unidad.