LOT NUMBER: DATE PURCHASED: / / Modern Farmhouse End Table Stock # BH17-084-098-49 # BH17-084-099-98 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOGUE: Modern Farmhouse End Table MODEL # BH17-084-098-49 / BH17-084-099-98 MADE IN CHINA MAXIMUM LOAD 50 lb. (22.6 kg) MAXIMUM LOAD 30 lb. (13.6 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. SPECIAL NOTE Please read the instruction sheets completely before assembly.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X 4 FINAL X CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Left Side Frame (Qty. 1) C- Right Side Frame (Qty. 1) D- Fixed Shelf (Qty. 1) E- Bottom Panel (Qty. 1) F- Back Panel (Qty. 1) G- Front Stretcher (Qty. 1) H- Drawer Front (Qty. 1) I- Drawer Left Side (Qty. 1) J- Drawer Right Side (Qty. 1) K- Drawer Back Panel (Qty. 1) (1) Large Cam Lock (Qty.
Drawer Assembling 6 6 6 6 2 2 2 Small Cam Lock (4 used in this step) Cam Bolt (4 used in this step) ② ⑥ 1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw 4 Cam Bolts (2) into the designated small holes on the Drawer Front (H). 3.
Drawer Assembling H 4. Slide the Drawer Bottom Panel (L) into the grooves between the Drawer Side Panels (I and J) until fully inserted into the Drawer Front (H).
Drawer Assembling K 4 4 K 4 J 4 I L M4 x 38 mm Screw (4 used in this step) ④ 5. Fasten the Drawer Back Panel (K) to the Drawer Side Panels (I and J) with four 38 mm Screws (4). Make sure that Drawer Bottom Panel (L) fits securely into the groove of the Drawer Back Panel (K). Tighten all the screws with a Phillips screwdriver.
Assembly Instructions 2 Cam Bolt (21 used in this step) ② 6. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), the Side Frames (B and C), the Fixed Shelf (D), the Back Panel (F) and the Front Stretcher (G) using a Phillips screwdriver.
Assembly Instructions 1 G 3 3 E Large Cam Lock (1 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ① ③ 7. Attach the Front Stretcher (G) to the Bottom Panel (E) with two 30 mm Wood Dowels (3) and one Large Cam Lock (1).
Assembly Instructions F 1 3 3 D Large Cam Lock (1 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ① ③ 8. Attach the Back Panel (F) to the Fixed Shelf (D) with two 30 mm Wood Dowels (3) and one Large Cam Lock (1).
Assembly Instructions F 3 3 1 E Large Cam Lock (1 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ① ③ 9. Attach the Bottom Panel assembly to the Back Panel (F) with two 30 mm Wood Dowels (3) and one Large Cam Lock (1).
Assembly Instructions F D E 1 1 G 3 3 C Large Cam Lock (7 used in this step) M8 x 30 mm Wood Dowel (7 used in this step) ① ③ 10. Attach the previous assembly to the Right Side Frame (C) with seven 30 mm Wood Dowels (3) and seven Large Cam Locks (1).
Assembly Instructions B 3 3 1 F 1 D E G Large Cam Lock (7 used in this step) M8 x 30 mm Wood Dowel (7 used in this step) ① ③ 11. Repeat the same procedure to attach the Left Side Frame (B) at the opposite end.
Assembly Instructions A 3 C 1 B Large Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 12. Stand the previous assembly upright. 13. Attach the Top Panel (A) to the Side Frames (B and C) with four 30 mm Wood Dowels (3) and four Large Cam Locks (1).
Assembly Instructions 5 Cam Lock Cover (4 used in this step) ⑤ 14. Plug the Cam Lock Covers (5) onto the visible Cams Locks to conceal the Cams. 15. Insert the assembled drawer into the frame. Extend the Ball Bearing Slide Tracks on the Side Panels (B and C) all the way forward (including ball bearing cart). Then align the Slide Runners on the assembled drawer with the Slide Tracks and push the drawer carefully inside until it stops.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO de LOTE: FECHA de COMPRA: / / Mesa lateral Modern Farmhouse Serie # BH17-084-098-49 # BH17-084-099-98 ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATÁLOGO: Mesa lateral Modern Farmhouse MODELO # BH17-084-098-49 / BH17-084-099-98 HECHO EN CHINA CARGA MÁXIMA 50 lb. (22.6 kg) CARGA MÁXIMA 30 lb. (13.6 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. NOTA ESPECIAL Por favor lea todo el instructive antes de ensamblar.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma, SI ES NECESARIO.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. A- Panel superior (Cant. 1) D- Repisa fija (Cant. 1) G- Soporte frontal (Cant. 1) J- Lado derecho del cajón (Cant. 1) (1) Tuerca de fijación grande (Cant. 21+1 extra) B- Marco lateral izquierdo (Cant. 1) E- Panel inferior (Cant. 1) H- Frente del cajón (Cant. 1) K- Panel posterior del cajón (Cant. 1) (2) Tornillo de fijación (Cant.
Ensamble del cajón 6 6 6 6 2 2 2 Tuerca de fijación chica (4 usados en este paso) Tornillo de fijación (4 usados en este paso) ② ⑥ 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Colocar 4 tornillos de fijación (2) en los agujeros chicos designados en el frente del cajón (H). 3.
Ensamble del cajón H 4. Deslizar el panel inferior del cajón (L) en las ranuras entre los paneles laterales del cajón (I y J) hasta que esté completamente insertado en el frente del cajón (H).
Ensamble del cajón K 4 4 K 4 J 4 I L Tornillo de M4 x 38 mm (4 usados en este paso) ④ 5. Sujetar el panel posterior del cajón (K) a los paneles laterales del cajón (I y J) con 4 tornillos de with 38 mm (4). Asegurar de que el panel inferior del cajón (L) entre en las ranura del panel posterior del cajón (K). Apretar los tornillos con el desarmador estrella.
Instructivo de ensamble 2 Tornillo de fijación (21 usados en este paso) ② 6. Colocar los tornillos de fijación (2) en los agujeros chicos designados en el panel superior (A), en los marcos laterales (B y C), en la repisa fija (D), en el panel posterior (F) y en el soporte frontal (G) usando el desarmador estrella.
Instructivo de ensamble 1 G 3 3 E Tuerca de fijación grande (1 usados en este paso) Perno de madera de M8 x 30 mm (2 usados en este paso) ① ③ 7. Adjuntar el soporte frontal (G) al panel inferior (E) con 2 pernos de madera de 30 mm (3) y una tuerca de fijación grande (1).
Instructivo de ensamble F 1 3 3 D Tuerca de fijación grande (1 usados en este paso) Perno de madera de M8 x 30 mm (2 usados en este paso) ① ③ 8. Adjuntar el panel posterior (F) a la repisa fija (D) con 2 pernos de madera de 30 mm (3) y una tuerca de fijación grande (1).
Instructivo de ensamble F 3 3 1 E Tuerca de fijación grande (1 usados en este paso) Perno de madera de M8 x 30 mm (2 usados en este paso) ① ③ 9. Adjuntar el ensamble del panel inferior al panel posterior (F) con 2 pernos de madera de 30 mm (3) y una tuerca de fijación grande (1).
Instructivo de ensamble F D E 1 1 G 3 3 C Tuerca de fijación grande (7 usados en este paso) Perno de madera de M8 x 30 mm (7 usados en este paso) ① ③ 10. Adjuntar el ensamble previo al marco lateral derecho (C) con 7 pernos de madera de 30 mm (3) y 7 tuercas de fijación grandes (1).
Instructivo de ensamble B 3 3 1 F 1 D E G Tuerca de fijación grande (7 usados en este paso) Perno de madera de M8 x 30 mm (7 usados en este paso) ① ③ 11. Repetir el mismo procedimiento para adjuntar el marco lateral izquierdo (B) al lado opuesto.
Instructivo de ensamble A 3 C 1 B Tuerca de fijación grande (4 usados en este paso) Perno de madera de M8 x 30 mm (4 usados en este paso) ① ③ 12. Poner el ensamble previo en posición vertical. 13. Adjuntar el panel superior (A) a lso marcos laterales (B y C) con 4 pernos de madera de 30 mm (3) y 4 tuercas de fijación grandes (1).
Instructivo de ensamble 5 Tapa de la tuerca de fijación (4 usados en este paso) ⑤ 14. Enchufar las tapas de las tuercas de fijación (5) sobre las tuercas visibles para esconderlas. 15. Insertar el cajón ensamblado en el marco. Extender los carriles de la corredera de baleros en los paneles laterales (B y C) todo el camino hacia enfrente (incluyendo el carrito de baleros).
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera, pruebela en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los ponga sobre la unidad.