LOT NUMBER: DATE PURCHASED: / / Ellis Shutter TV Storage Console Stock # BH18-084-097-49 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Ellis Shutter TV Storage Console MODEL # BH18-084-097-49 MADE IN MALAYSIA HOLDS MOST 75” FLAT PANEL TVs MAXIMUM LOAD 135 lb. (61.3 kg) PLACE TV BEHIND THE STOPPER MAXIMUM LOAD 50 lb. (22.7 kg) THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X X 4 FINAL CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 1) D- Left Side Panel (Qty. 1) E- Right Side Panel (Qty. 1) F- Lower Partition Panel (Qty. 1) G- Left Door (Qty. 2) H- Right Door (Qty. 2) I- Adjustable Shelf (Qty. 2) J- Upper Partition Panel (Qty. 1) M- Bottom Front Stretcher (Qty. 1) (with floor leveler) K- Front Molding (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. P- Back Panel (Qty. 1) Q- Stop Rail (Qty. 1) (1) Cam Lock (Qty. 42+2 extra) (4) M4 x 50 mm Screw (Qty. 2+1 extra) (7) Cam Lock Cover (Qty. 24+1 extra) (11) 1/4" x 19 mm Bolt (Qty. 4+1 extra) R- Cable Wheel (Qty. 2) (2) Cam Bolt (Qty. 42+2 extra) (3) M8 x 30 mm Wood Dowel (Qty. 43+2 extra) (5) M3.5 x 15 mm Washer Head Screw (Qty.
Assembly Instructions A 2 B C Cam Bolt (20 used in this step) ② 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) and Bottom Panel (C) and Fixed Shelf (B) using a Phillips screwdriver.
Assembly Instructions D E 2 L M N K K Cam Bolt (16 used in this step) ② 3. Securely screw the Cam Bolts (2) into the designated small holes on the Side Panels (D and E), the Stretchers (L, M and N) and the Front Moldings (K).
Assembly Instructions B 3 F 1 Cam Lock (2 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ① ③ 4. Glue two Wood Dowels (3) into the inner holes of the Lower Partition Panel (F) and attach it to the Fixed Shelf (B) by engaging two Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
Assembly Instructions B 2 B J 3 1 Cam Lock (2 used in this step) Cam Bolt (2 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ① ② ③ 5. Securely screw the Cam Bolts (2) into the designated small holes on the Fixed Shelf (B). 6. Attach the Upper Partition Panel (J) to the Fixed Shelf (B) with two Cam Locks (1) and two Wood Dowels (3).
Assembly Instructions E B 3 D 1 Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 7. Attach Side Panels (D and E) to the Fixed Shelf (B) with four Wood Dowels (3) and four Cam Locks (1).
Assembly Instructions K 3 K 1 E K B D Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 8. Attach one Front Molding (K) to each Side Panel (D and E) with two Wood Dowels (3) and two Cam Locks (1).
Assembly Instructions 8 9 A 1/4" x 12 mm Bolt (2 used in this step) Corner Connector (2 used in this step) ⑨ ⑧ 9. Fasten two Corner Connectors (9) to the Top Panel (A) with two 12 mm Bolts (8).
Assembly Instructions 1 8 L 3 A Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (1 used in this step) ① ③ 1/4" x 12 mm Bolt (2 used in this step) ⑧ 10. Attach the Top Front Stretcher (L) to the Top Panel (A) with one 30 mm Wood Dowel (3) and four Cam Locks (1). 11. Insert two 12 mm Bolts (8) through the Corner Connectors (9) and screw into the Top Front Stretcher (L).
Assembly Instructions L K A E K J 3 D 1 Cam Lock (6 used in this step) M8 x 30 mm Wood Dowel (10 used in this step) ① ③ 12. Glue ten Wood Dowels (3) into the inner holes on the vertical panels (D, E, J and K). 13. Position the Top Panel (A) onto the inserted Wood Dowels (3) and fasten it in place with six Cam Locks (1).
Assembly Instructions 3 1 O N M O Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 14. Combine the Bottom Front Stretcher (M), Back Stretcher (N) and Side Stretchers (O) together with four Wood Dowels (3) and four Cam Locks (1).
Assembly Instructions O N M O C 1 3 Cam Lock (12 used in this step) M8 x 30 mm Wood Dowel (10 used in this step) ① ③ 15. Attach the assembled base to the Bottom Panel (C) with the 30 mm Wood Dowels (3) and the Cam Locks (1).
Assembly Instructions 2 C Cam Bolt (4 used in this step) ② 16. Securely screw the Cam Bolts (2) into the designated small holes on the top of Bottom Panel (C).
Assembly Instructions 1 3 E F M D C N Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (6 used in this step) ① ③ 4 4 M4 x 50 mm Screw (2 used in this step) ④ 17. Glue six Wood Dowels (3) into the inner holes on the vertical panels (D, E and F). 18. Position the Bottom Panel (C) onto the inserted Wood Dowels (3) and fasten it in place with four Cam Locks (1) and two 50 mm Screws (4).
Assembly Instructions 5 5 P E P M3.5 x 15 mm Washer Head Screw (36 used in this step) ⑤ 19. Now, go back and securely tighten all the Cam Locks and the Screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 20. Flip the previous assembly around at its front edges. 21. Unfold and pick up the Back Panel (P) and align the pre-drilled large holes with the threaded inserts on the Fixed Shelf (B).
Assembly Instructions 11 R P E 1/4" x 19 mm Bolt (4 used in this step) 22. Attach two Cable Wheels (R) to the backside of the unit with four 19 mm Bolts (11). NOTE: You can use the Cable Wheels to help keep your entertainment center’s cables and cords organized.
Assembly Instructions E F D H G G H 1 23. Stand the unit upright. 24. Pick up the Right Doors (H) and attach the extended Hinge Arms to the Hinge Bases installed on Right Side Panel (E) and Lower Partition Panel (F). Loosen the bolt on the back of Hinge Base for a comfortable fit. Align and insert the “U” slot on Hinge Arm under the bolt head on the back of Hinge Base. Make sure that both door hinges engage and function properly. Tighten the bolt on the Hinge Base to lock the hinges in place. 25.
Assembly Instructions 7 6 I I I 6 10 Shelf Support (8 used in this step) Cam Lock Cover (24 used in this step) ⑥ Rubber Bumper (8 used in this step) ⑦ ⑩ 27. With the doors open, insert the Shelf Supports (6) into the desired holes in the sides of the compartments. Make sure you place the four Shelf Supports in the same level, so the shelf is not tilted. Tilt and rest the Adjustable Shelves (I) onto the Shelf Supports (6). 28.
Assembly Instructions Q A A NOTE: You must install the Strip Stopper to prevent the TV from tipping when placing your flat panel television directly on the console. 30. Remove the paper backing from the Stop Rail (Q), then properly align the Stop Rail with the top edge of the stopper template on the Top Panel (A). Press down on the Stop Rail to help adhesion. 31. Carefully remove the stopper template from the Top Panel (A).
Assembly Instructions Tools required (not provided): Phillips screwdriver, stud finder, power drill and 3 mm/0.1 in drill bit. 32. Ask for assistance to position the unit at the desired location against a wall. If necessary, adjust the preattached floor levelers at the bottom of the Bottom Front Stretcher (M) to level the unit. 33. Follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to attach the tip-over restraints to the unit and the wall.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO DEL LOTE: FECHA DE COMPRA / / Mueble Ellis con persianas para guardar la televisión Serie # BH18-084-097-49 ENSAMBLE REQUERIDO POR ADULTOS Si tiene alguna pregunta relacionada con el montaje o si faltan piezas, NO devuelva este producto al establecimiento donde lo adquirió.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Mueble Ellis con persianas para guardar la Televisión MODELO # BH18-084-097-49 HECHO EN MALASIA PARA LA MAYORÍA DE TELEVISIONES PANTALLA PLANA 75” CARGA MÁXIMA 135 lb. (61.3 kg) CARGA MÁXIMA 135 lb. (61.3 kg) PONER LA TV DETRÁS DEL TOPE CARGA MÁXIMA 50 lb. (22.7 kg) ESTA UNIDAD NO DEBE UTILIZARSE CON TELEVISIONES CRT O DE TUBO.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 y 5 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma, SI ES NECESARIO.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y herramientas indicadas se encuentran presentes antes del comienzo del montaje. A- Panel superior (Cant. 1) B- Estanteria fija (Cant. 1) C- Panel inferior (Cant. 1) D- Panel izquierdo (Cant. 1) E- Panel derecho (Cant. 1) F- Panel de la partición inferior (Cant. 1) G- Puerta izquierda (Cant. 2) J- Panel de partición superior (Cant. 1) M- Bastidor inferior frontal (Cant.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y herramientas indicadas se encuentran presentes antes del comienzo del montaje. P- Panel posterior (Cant. 1) Q- Barra de tope (Cant. 1) (1) Tuerca de fijación (Cant. 42+2 extra) (4) Tornillo M4 x 50 mm (Cant. 2+1 extra) (2) Perno de fijación (Cant. 42+2 extra) R- Guía de cable (Cant. 2) (3) Clavija de madera M8 x 30 mm (Cant. 43+2 extra) (5) Tornillo de arandela M3.
Instrucciones de ensamblaje A 2 B C Perno de fijación (se usan 20 en este paso) ② 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Atornille firmemente los pernos de fijación (2) en los pequeños orificios indicados en el panel superior (A) el panel inferior (C) y la estantería fija (B) usando un destornillado Phillips.
Instrucciones de ensamblaje D E 2 L M N K K Perno de fijación (Se usan 16 en este paso) ② 3. Atornille firmemente los pernos de fijación (2) en los pequeños orificios indicados en los paneles laterales (D y E), los bastidores (L, M y N) y las molduras frontales (K).
Instrucciones de ensamblaje B 3 F 1 Clavija de madera M8 x 30 mm Tuerca de fijación (Se usan 2 en este paso) (Se usan 2 en este paso) ③ ① 4. Pegue dos clavijas de madera (3) en los orificios interiores del panel de partición inferior (F) y ensámblelo en la estantería fija (B) encajando dos tuercas de fijación (1) (Consulte la página 3 del suplemento de manejo del sistema de tuercas de fijación).
Instrucciones de ensamblaje B 2 B J Tuerca de fijación (Se usan 2 en este paso) 3 1 Perno de fijación (Se usan 2 en este paso) ② ① Clavija de madera M8 x 30 mm (Se usan 2 en este paso) ③ 5. Atornille firmemente los pernos de fijación (2) en los pequeños orificios indicados en la estantería fija (B). 6. Fije el panel de partición superior (J) a la estantería fija (B) con dos pernos de fijación (1) y dos clavijas de madera (3).
Instrucciones de ensamblaje E B 3 D 1 Clavija de madera M8 x 30 mm Tuerca de fijación (Se usan 4 en este paso) (Se usan 4 en este paso) ① ③ 7. Fije los paneles laterales (D y E) a la estantería fija (B) con cuatro clavijas de madera (3) y cuatro tuercas de fijación (1).
Instrucciones de ensamblaje K 3 K 1 E K B D Tuerca de fijación (Se usan 4 en este paso) Clavija de madera M8 x 30 mm (Se usan 4 en este paso) ① ③ 8. Fije una moldura frontal (K) a cada panel lateral (D y E) con dos clavijas de madera (3) y dos tuercas de fijación (1).
Instrucciones de ensamblaje 8 9 A Perno 1/4" x 12 mm (Se usan 2 en este paso) Conector de esquinas (Se usan 2 en este paso) ⑨ ⑧ 9. Asegure dos conectores de esquina (9) al panel superior (A) con dos pernos de 12 mm (8).
Instrucciones de ensamblaje 1 8 L 3 A Tuerca de fijación (Se usan 4 en este paso) Clavija de madera M8 x 30 mm (Se usan 1 en este paso) ① ③ Perno 1/4" x 12 mm (Se usan 2 en este paso) ⑧ 10. Fije el bastidor superior frontal (L) al panel superior (A) con una clavija de madera de 30 mm (3) y cuatro tuercas de fijación (1). 11. Inserte dos pernos de 12 mm (8) a través de los conectores de esquina (9) y atorníllelos en el bastidor superior frontal (L).
Instrucciones de ensamblaje L K A E K J 3 D 1 Clavija de madera M8 x 30 mm Tuerca de fijación (Se usan 6 en este paso) (Se usan 10 en este paso) ① ③ 12. Pegue diez clavijas de madera (3) en los orificios interiores de los paneles verticales (D, E, J y K). 13. Coloque el panel superior (A) en las clavijas de madera insertadas (3) y asegúrelo en su posición con seis tuercas de fijación (1).
Instrucciones de ensamblaje 3 1 O N M O Tuerca de fijación (Se usan 4 en este paso) Clavija de madera M8 x 30 mm (Se usan 4 en este paso) ① ③ 14. Una entre si el bastidor inferior frontal (M), el bastidor posterior (N) y los bastidores laterales (O) con cuatro clavijas de madera (3) y cuatro tuercas de fijación (1).
Instrucciones de ensamblaje O N M O C 1 3 Tuerca de fijación (Se usan 12 en este paso) Clavija de madera M8 x 30 mm (Se usan 10 en este paso) ① ③ 15. Fije la base así montada al panel inferior (C) con las clavijas de madera de 30 mm (3) y las tuercas de fijación (1).
Instrucciones de ensamblaje 2 C Perno de fijación (Se usan 4 en este paso) ② 16. Atornille firmemente los pernos de fijación (2) en los pequeños orificios indicados sobre el panel inferior(C).
Instrucciones de ensamblaje 1 3 E F M D C N Tuerca de fijación (Se usan 4 en este paso) Clavija de madera M8 x 30 mm (Se usan 6 en este paso) ① 4 4 Tornillo M4 x 50 mm (Se usan 2 en este paso) ④ ③ 17. Pegue seis clavijas de madera (3) en los orificios interiores de los paneles verticales (D, E y F). 18. Coloque el panel inferior (C) en las clavijas de madera insertadas (3) y asegúrelo en su posición con cuatro tuercas de fijación (1) y dos tornillos de 50 mm (4).
Instrucciones de ensamblaje 5 5 P E P Tornillo de arandela M3.5 x 15 mm (Se usan 4 en este paso) ⑤ 19. Ahora, vuelva atrás y asegure firmemente todas las tuercas de fijación y tornillos. Asegúrese de que todas las partes están firmes y de que no quedan huecos entre las partes. Esto ayudara a mantener la unidad en su sitio. 20. Dele la vuelta al montaje sobre sus bordes superiores. 21.
Instrucciones de ensamblaje 11 R P E Perno de 1/4" x 19 mm (Se usan 4 en este paso) 22. Fije dos guías de cable (R) a la parte posterior de la unidas con cuatro pernos de 19 mm (11). NOTA: Puede usar las guías de cable para mantener ordenados los cables e hilos de su equipo de entretenimiento.
Instrucciones de ensamblaje E F D H G G H 1 23. Coloque la unidad en vertical. 24. Levante las puertas (H) y fije los brazos de bisagra extendidos en las bases de las bisagras instaladas en el panel lateral derecho(E) y el panel de partición inferior (F) Afloje el perno en el posterior de la base de la bisagra para un ajuste adecuado. Alinee e inserte la ranura en U del brazo de la bisagra bajo la cabeza del perno en el posterior de la base de la bisagra.
Instrucciones de ensamblaje 7 6 I I I 6 10 Soporte de la estantería (Se usan 4 en este paso) Tapa de la tuerca de fijación (Se usan 4 en este paso) ⑥ ⑦ Topes de goma (Se usan 4 en este paso) ⑩ 27. Con las puertas abiertas, coloque los soportes de la estantería (6) en los orificios de los compartimentos de su elección. Asegúrese de que coloca los cuatro soportes al mismo nivel para que la estantería no quede inclinada.
Instrucciones de ensamblaje Q A A NOTA: Debe instalar el tope de tira para prevenir el volcado de la televisión cuando instale su televisión de pantalla plana directamente sobre la consola. 30. Retire la cubierta de papel de la barra de tope(Q), a continuación, alinee adecuadamente la barra de tope con el borde superior de la plantilla del tope en el panel superior (A). Presione sobre la barra de tope para ayudar a su pegado. 31. Retire cuidadosamente la plantilla del tope del panel superior (A).
Instrucciones de ensamblaje Herramientas necesarias (no incluidas): Desarmador estrella, detector de vigas, taladro eléctrico y taladro de 3mm (0.1"). 32. Pida ayuda para colocar la unidad contra la pared en la posición deseada. Si fuera necesario, ajuste los niveladores de piso prefijados en la parte inferior del bastidor inferior frontal (M). 33. Siga las instrucciones impresas en la bolsa de plástico que contiene el kit anti-volcado para colocar los protectores anti-volcado en la unidad y la pared.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayones. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.