LOT NUMBER: DATE PURCHASED: / / Bankston White Dining Table Stock # BH17-084-097-29 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS 1. Maximum load weight on table is 181.4 kg (400 pounds). THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. GENERAL INFORMATION, TIPS AND TRICKS 1. Please read the Assembly Instructions prior to assembling the unit. 2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface. 3.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Table Top (Qty. 1) B- Leg (Qty. 4) (1) 5/16” x 55 mm Bolt (Qty. 8+1 extra) (2) Lock Washer (Qty. 8+1 extra) (3) Flat Washer (Qty. 8+1 extra) 4 mm Hex Wrench (Qty. 1) Tools required: Hex wrench (provided) and Philips screwdriver (not provided).
Assembly Instructions A 1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Position the Table Top (A) upside down on a level and protective surface as shown. 3. Remove the additional wood blocks attached at the corners by unscrewing the wood screws. These are used for shipping purposes only. After removing them, please discard.
Assembly Instructions B B 3 2 A 1 A B B B B A Flat Washer (8 used in this step) 5/16” x 55 mm Bolt (8 used in this step) ① Lock Washer (8 used in this step) ③ ② DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts. 4.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently.
LOTE NÚMERO: FECHA DE COMPRA: / / Mesa de comedor Bankston Blanco Serie # BH17-084-097-29 ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMOS PESOS RECOMENDADOS 1. Máxima carga recomendada en la mesa es de 181.4 kg (400 libras). ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. INFORMACIÓN GENERAL, RECOMENDACIONES Y TRUCOS 1. Por favor lea el instructivo antes de comenzar el ensamble. 2. Para evitar daños, ensamble la unidad en una area nivelada y libre de abrazivos. 3. Mantener el Herraje fuera de las manos de los niños.
Lista de Partes y Ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y ferretería antes de iniciar el ensamblado. A- Tapa de mesa (Cant. 1) B- Pata (Cant. 4) (1) Tornillo de 5/16” x 55 mm (Cant. 8+1 extra) (2) Arandela de presión (Cant. 8+1 extra) (3) Arandela plana (Cant. 8+1 extra) Llave hexagonal 4 mm (Cant. 1) Herramienta requerida: Llave hexagonal (proveida) y desarmador estrella (no proveido).
Instrucciones de ensamble A 1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas. Ensamblar la unidad sobre en una area encarpetada o el cartón vacío para evitar cualquier rasguño. 2. Coloque la superficie de la mesa (A) boca abajo sobre una superficie plana y protectora, como se muestra. 3. Retire los bloques de madera adicionales que se adjuntan en las esquinas aflojando los tornillos. Estos se utilizan para propósitos de envío.
Instrucciones de ensamble B B 3 2 A 1 A B B B B Tornillo de 5/16” x 55 mm (8 usados en este paso) ① A Arandela de presión (8 usados en este paso) Arandela plana (8 usados en este paso) ② ③ NO APRIETE completamente los tornillos o tuercas hasta que todas las partes esten ensambladas. Para evitar daños a la rosca no apriete demas los tornillos o tuercas. 4.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera revisar en una área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando ponga sobre la unidad.