LOT NUMBER: DATE PURCHASED: / / Steele End Table Stock # BH46-021-199-01 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOGUE: Steele End Table (BH46-021-199-01) MADE IN CHINA MAXIMUM LOAD 50 lb. (22.6 kg) MAXIMUM LOAD 10 lb. (4.5 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. SPECIAL NOTE Please read the instruction sheets completely before assembly.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X 4 FINAL X CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Left Side Panel (Qty. 1) D- Bottom Panel (Qty. 1) E- Fixed Shelf (Qty. 1) G- Bottom Short Support (Qty. 2) (Qty. 1) J- Drawer Left Side (Qty. 1) (4) M8 x 30 mm Wood Dowel (Qty. 20+1 extra) (7) Handle (Qty. 1) F- Back Panel (Qty. 1) H- Bottom Long Support (Qty. 2) (Qty. 1) K- Drawer Right Side (Qty.
Drawer Assembling 1 K J 3 3 I Cam Bolt (4 used in this step) Small Cam Lock (4 used in this step) ③ ① 1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw 4 Cam Bolts (3) into the designated small holes on the Drawer Front (I). 3.
Drawer Assembling M K J I 4. Slide the Drawer Bottom Panel (M) into the grooves between the Drawer Side Panels (J and K) until fully inserted into the Drawer Front (I).
Drawer Assembling L 5 L K M J K M J 5 I I M4 x 38 mm Screw (4 used in this step) ⑤ 5. Fasten the Drawer Back Panel (L) to the Drawer Side Panels (J and K) with four 38 mm Screws (5). Make sure that Drawer Bottom Panel (M) fits securely into the groove of the Drawer Back Panel (L). Tighten all the screws with a Phillips screwdriver.
Drawer Assembling 8 8 I 7 Handle (1 used in this step) Handle Bolt (2 used in this step) ⑦ ⑧ 6. Turn the assembled drawer upright. 7. Attach the Handle (7) to the outside of the Drawer Front (I) with two Handle Bolts (8).
Assembly Instructions 6 6 6 H 6 G 4 4 4 H G H 4 G 4 4 H 4 4 G D M4 x 50 mm Screw (8 used in this step) M8 x 30 mm Wood Dowel (12 used in this step) ⑥ ④ 8. Attach the Bottom Long Supports (H) between the Bottom Short Supports (G) with four 30 mm Wood Dowels (4). 9. Fasten the previous assembly to the Bottom Panel (D) with eight 30 mm Wood Dowels (4) and eight 50 mm Screws (6).
Assembly Instructions A 3 E C B D Cam Bolt (12 used in this step) ③ 10. Securely screw the Cam Bolts (3) into the designated small holes on the Top Panel (A), the Side Panels (B and C), the Bottom Panel (D) and the Fixed Shelf (E) using a Phillips screwdriver.
Assembly Instructions F 2 4 2 E Large Cam Lock (2 used in this step) M8 x 30 mm Wood Dowel (1 used in this step) ② ④ 11. Attach the Back Panel (F) to the Fixed Shelf (E) with one 30 mm Wood Dowel (4) and two Cam Locks (2) making sure the cam locks will face inward.
Assembly Instructions C 4 2 E 4 2 F Large Cam Lock (2 used in this step) M8 x 30 mm Wood Dowel (3 used in this step) ② ④ 12. Attach the Fixed Shelf assembly to the Right Side Panel (C) with three 30 mm Wood Dowels (4) and two Cam Locks (2).
Assembly Instructions C 2 E 4 F B 2 4 Large Cam Lock (2 used in this step) M8 x 30 mm Wood Dowel (3 used in this step) ② ④ 13. Repeat the same procedure to attach the Left Side Panel (B) at the opposite end.
Assembly Instructions A 10 C 2 10 B 2 Large Cam Lock (4 used in this step) M15x 60 mm Wood Dowel (4 used in this step) ② ⑩ 14. Attach the Top Panel (A) to the Side Panels (B and C) with four 60 mm Wood Dowels (10) and four Cam Locks (2).
Assembly Instructions C 10 B 10 2 10 2 4 D 10 Large Cam Lock (2 used in this step) M8 x 30 mm Wood Dowel (1 used in this step) ② ④ M15x 60 mm Wood Dowel (4 used in this step) ⑩ 15. Insert four 60 mm Wood Dowels (10) into the bottom holes on the Side Panels (B and C) and insert one 30 mm Wood Dowel (4) into the middle hole on the Back Panel (F). Position the Bottom Panel (D) onto the inserted wood dowels and attach to the Back Panel (F) with two Large Cam Locks (2).
Assembly Instructions C B D 6 6 M4 x 50 mm Screw (4 used in this step) ⑥ 16. Fasten the Bottom Panel (D) to the Side Panels (B and C) with four 50 mm Screws (6).
Assembly Instructions 9 C B K J I Cam Lock Cover (4 used in this step) ⑨ 17. Plug the Cam Lock Covers (9) onto the visible Cams Locks to conceal the Cams. 18. Insert the assembled drawer into the frame. Extend the Ball Bearing Slide Tracks on the Side Panels (B and C) all the way forward (including ball bearing cart). Then align the Slide Runners on the assembled drawer with the Slide Tracks and push the drawer carefully inside until it stops.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
LOTE NÚMERO: FECHA DE COMPRA: / / Mesa esquina Steele Serie # BH46-021-199-01 ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda en que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estandar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMOS PESOS RECOMENDADOS FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Mesa esquina Steele (BH46-021-199-01) HECHO EN CHINA MÁXIMA CARGA 50 lb. (22.6 kg) MÁXIMA CARGA 10 lb. (4.5 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. NOTA ESPECIAL Por favor lea todo el instructive antes de ensamblar. Examinar todo el material de empaque antes de tirar el cartón.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma SI ES NECESARIO.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado. A- Panel superior (Cant. 1) D- Panel inferior (Cant. 1) G- Soporte inferior corto (Cant. 2) J- Lado izq. de cajón (Cant. 1) C- Panel derecho (Cant. 1) E- Repisa fija (Cant. 1) F- Panel posterior (Cant. 1) H- Soporte inferior largo (Cant. 2) K- Lado der. de cajón (Cant.1) (1) Tuerca de fijación chica (Cant.
Ensamble del cajón 1 K J 3 3 I Tornillo de fijación (4 usados en este paso) Tuerca de fijación chica (4 usados en este paso) ③ ① 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Asegurar 4 tornillos de fijación (3) en los agujeros pequeños designados en el frente de cajón (I). 3.
Ensamble del cajón M K J I 4. Deslice el panel inferior del cajón (M) en las ranuras entre los paneles laterales del cajón (J y K) hasta que esté completamente insertado en el frente del cajón (I).
Ensamble del cajón L 5 L K M J K M J 5 I I Tornillo M4 x 38 mm (4 usados en este paso) ⑤ 5. Fijar el panel posterior del cajón (L) a los paneles laterales del cajón (J y K) con cuatro tornillos de 38 mm (5). Asegúrese de que el panel inferior de cajón (M) encaja perfectamente en la ranura del panel posterior del cajón (L). Apriete todos los tornillos con un destornillador estrella.
Ensamble del cajón 8 8 I 7 Manija (1 usado en este paso) Tornillo para manija (2 usados en este paso) ⑦ ⑧ 6. Gire el cajón en su posición vertical. 7. Adjunte la manija (7) en la parte exterior del frente de cajón (I) con 2 tornillos para manija (8).
Instrucciones de ensamble 6 6 6 H 6 G 4 4 4 H G H 4 G 4 4 H 4 4 G D Tornillo M4 x 50 mm (8 usados en este paso) Perno M8 x 30 mm madera (12 usados en este paso) ⑥ ④ 8. Coloque los soportes inferiores largos (H) entre los soportes inferiores cortos (G) con cuatro pernos de 30 mm de madera (4). 9. Sujetar el sistema anterior al panel inferior (D) con ocho pernos de 30 mm de madera (4) y ocho tornillos de 50 mm (6).
Instrucciones de ensamble A 3 E C B D Tornillo de fijación (12 usados en este paso) ③ 10. Ajuste los tornillos de fijación (3) en los orificios pequeños designados en el panel superior (A), los paneles laterales (B y C), el panel inferior (D) y la repisa fija (E) con un destornillador estrella.
Instrucciones de ensamble F 2 4 2 E Tuerca de fijación grande (2 usados en este paso) Perno M8 x 30 mm madera (1 usado en este paso) ② ④ 11. Una el panel posterior (F) a la repisa fija (E) con un perno de 30 mm de madera (4) y dos tuercas de fijación (2) asegurándose de que las tuercas se enfrentarán hacia adentro.
Instrucciones de ensamble C 4 2 E 4 2 F Tuerca de fijación grande (2 usados en este paso) Perno M8 x 30 mm de madera (3 usados en este paso) ② ④ 12. Acople el ensamble de repisa fija al panel lateral derecho (C) con tres pernos de 30 mm de madera (4) y dos tuercas de fijación (2).
Instrucciones de ensamble C 2 E 4 F B 2 4 Tuerca de fijación grande (2 usados en este paso) Perno M8 x 30 mm de madera (3 usados en este paso) ② ④ 13. Repetir el mismo proceso para adjuntar el lado izquierdo (B) al extremo contrario.
Instrucciones de ensamble A 10 C 2 10 B 2 Tuerca de fijación grande (4 usados en este paso) Perno M15x 60 mm madera (4 usados en este paso) ② ⑩ 14. Coloque el panel superior (A) a los paneles laterales (B y C) con cuatro pernoss de madera de 60 mm (10) y cuatro tuercas de fijación (2).
Instrucciones de ensamble C 10 B 10 2 10 2 4 D 10 Tuerca de fijación grande (2 usados en este paso) ② Perno M8 x 30 mm de madera (1 usado en este paso) ④ Perno M15x 60 mm de madera (4 usados en este paso) ⑩ 15. Inserte cuatro pernos de 60 mm de madera (10) en los orificios inferiores de los paneles laterales (B y C) e inserte un perno de 30 mm de madera (4) en el orificio central en el panel posterior (F).
Instrucciones de ensamble C B D 6 6 Tornillo de M4 x 50 mm (4 usados en este paso) ⑥ 16. Fijar el panel inferior (D) a los paneles laterales (B y C) con cuatro tornillos de 50 mm (6).
Instrucciones de ensamble 9 C B K J I Tapa tuerca de fijación (4 usados en este paso) ⑨ 17. Cubrir con las tapas de tuerca de fijación (9) las tuercas que esten visibles para ocultarlas. 18. Insertar el cajón izquierdo y el cajón de archivos ensamblados en el marco. Extender los rieles de la corredera de baleros en los paneles laterales (B y C) todo el camino hacia enfrente (incluyendo el carrito de baleros).
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.