LOT NUMBER: DATE PURCHASED: / / Steele Audio Video Tower Stock # BH46-084-099-53 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOGUE: Steele Audio Video Tower (BH46-084-099-53) MADE IN CHINA MAXIMUM LOAD 50 lb. (22.6 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. SPECIAL NOTE Please read the instruction sheets completely before assembly. Examine all packaging material before discarding carton.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X 4 FINAL X CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Left Side Panel (Qty. 1) D- Bottom Panel (Qty. 1) G- Bottom Long Support (Qty. 2) E- Fixed Shelf (Qty. 1) H- Bottom Short Support (Qty. 2) K- Large Adjustable Shelf (1) Cam Lock (Qty. 2) (Qty. 8+1 extra) (4) M8 x 30 mm Wood Dowel (Qty. 16+1 extra) (7) Handle (Qty. 2) (10) Door Stopper (Qty. 1) Glue (Qty.
Assembly Instructions 5 5 H G 4 4 4 4 5 5 G H 4 H G 4 4 H 4 G D M4 x 50 mm Screw (8 used in this step) M8 x 30 mm Wood Dowel (12 used in this step) ⑤ ④ 1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Attach the Bottom Short Supports (H) between the Bottom Long Supports (G) with four 30 mm Wood Dowels (4). 3.
Assembly Instructions A B C 2 Cam Bolt (8 used in this step) ② 4. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) and the Side Panels (B and C) using a Phillips screwdriver.
Assembly Instructions 9 E 10 M3 x 12 mm Screw (2 used in this step) Door Stopper (1 used in this step) ⑨ ⑩ 5. Using the pilot holes as a guide, attach the Door Stopper (10) to the Fixed Shelf (E) with two 12 mm Screws (9) as shown.
Assembly Instructions B 4 E 1 4 4 1 1 C 4 1 Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ④ 6. Attach the Fixed Shelf (E) to the Side Panels (B and C) with four 30 mm Wood Dowels (4) and four Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
Assembly Instructions A 3 1 3 B 1 C Cam Lock (4 used in this step) M15x 60 mm Wood Dowel (4 used in this step) ① ③ 7. Attach the Top Panel (A) to the Side Panels (B and C) with four 60 mm Wood Dowels (3) and four Cam Locks (1).
Assembly Instructions B C 3 3 D 5 5 M15x 60 mm Wood Dowel (4 used in this step) M4 x 50 mm Wood Screw (4 used in this step) ③ ⑤ 8. Attach the Bottom Panel (D) to the Side Panels (B and C) with four 60 mm Wood Dowels (3) and four 50 mm Wood Screws (5).
Assembly Instructions 13 13 B J C D M3.5 x 15 mm Washer Head Screw (14 used in this step) ⑬ NOTE: We recommend attaching the back panel with the screws at the corners first. 9. Now, go back and tighten all cam locks and screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 10. Position the Back Panel (J) to the back edges of the assembled unit. Make sure that the overlaps on the panels are even all the way around.
Assembly Instructions 8 7 8 I 7 Handle (2 used in this step) Handle Bolt (4 used in this step) ⑦ ⑧ 11. Attach the Handles (7) to the outside of the Door Panel (I) with four Handle Bolts (8).
Assembly Instructions I B B I 1 2 B I 12. Stand the assembled unit upright. 13. Pick up the Door (I) and attach the extended Hinge Arms to the Hinge Bases installed on the Left Side Panel (B). Loosen the bolt on the back of Hinge Base for an easy fit. Align and insert the “U” slot on Hinge Arm under the bolt head on the back of Hinge Base. Make sure that both door hinges engage and function properly. Tighten the bolt on the Hinge Base to lock the hinges in place. 14.
Assembly Instructions B/C 6 C B K F/K K 6 B/C F Shelf Pin (12 used in this step) ⑥ 15. Insert the Shelf Pins (6) into the desired holes in the sides of the compartments. Make sure you place the four Shelf Pins in the same level so the shelf is not tilted. Tilt and rest the Adjustable Shelves (F and K) onto the Shelf Pins (6) with the end notches of the Shelf fit onto the Shelf Pins properly.
Assembly Instructions 12 C B 11 I I Cam Lock Cover (4 used in this step) Rubber Bumper (1 used in this step) ⑫ ⑪ 16. Peel off one Rubber Bumper (11) from the bumper card and stick it at the outer corner of the Door (I) where it comes in contact with the Door Stopper (10). 17. Plug the Cam Lock Covers (12) onto the visible Cams Locks to conceal the Cams.
Assembly Instructions 18. Position the unit at the desired location against a wall. 19. Follow the instructions printed on the plastic bag containing the tipping restraint hardware to attach the tip-over restraints to the unit and the wall. NOTE: The tipping restraint hardware included is for drywall construction. It will be necessary to drill holes for the wall anchors. Depending upon your wall construction, different anchor hardware may be required.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
LOTE NÚMERO: FECHA DE COMPRA: / / Torre Audio Video Steele Serie # BH46-084-099-53 ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda en que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMOS PESOS RECOMENDADOS FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Torre audio/video Steele (BH46-084-099-53) HECHO EN CHINA MÁXIMA CARGA 50 lb. (22.6 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. NOTA ESPECIAL Por favor lea todo el instructive antes de ensamblar. Examinar todo el material de empaque antes de tirar el cartón.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma SI ES NECESARIO.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamblado A- Panel superior (Cant. 1) B- Panel lateral izq. (Cant. 1) D- Panel inferior (Cant. 1) G- Soporte inferior largo (Cant. 2) E- Repisa fija (Cant.1) H- Soporte inferior corto (Cant.2) (7) Manija (Cant. 2) (10) Tope puerta (Cant. 1) Pegamento (Cant. 1) (5) Tornillo de M4 x 50 mm (Cant.12+1 extra) (8) Tornillo de manija (Cant.
Instrucciones de ensamble 5 5 H G 4 4 4 4 5 5 G H 4 H G 4 4 H 4 G D Tornillo M4 x 50 mm (8 usados en este paso) Perno M8 x 30 mm de madera (12 usados en este paso) ⑤ ④ 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Coloque los soportes inferiores cortos (H) entre los soportes inferiores largos (G) con cuatro pernos de 30 mm de madera (4). 3.
Instrucciones de ensamble A B C 2 Tornillo de fijación (8 usados en este paso) ② 4. Adjuntar los tornillos de fijación (2) en los orificios pequeños designados en el panel superior (A) y los paneles laterales (B y C) con un desarmador estrella.
Instrucciones de ensamble 9 E 10 Tornillo M3 x 12 mm (2 usados en este paso) Tope de puerta (1 usado en este paso) ⑨ ⑩ 5. Usar los orificios piloto como guía, coloque el tope de la puerta (10) a la repisa fija (E) con dos tornillos de 12 mm (9) como se muestra.
Instrucciones de ensamble B 4 E 1 4 4 1 1 C 4 1 Tuerca de fijación (4 usados en este paso) M8 x 30 mm de madera (4 usados en este paso) ① ④ 6. Coloque la repisa fija (E) a los paneles laterales (B y C) con cuatro pernos de 30 mm de madera (4) y cuatro tuercas de fijación (1) (Consulte la página 3 del sistema de tuerca de fijación y su operación).
Instrucciones de ensamble A 3 1 3 B 1 C Tuerca de fijación (4 usados en este paso) Perno M15x 60 mm de madera (4 usados en este paso) ① ③ 7. Coloque el panel superior (A) a los paneles laterales (B y C) con cuatro pernos de 60 mm de madera (3) y cuatro tuercas de fijación (1).
Instrucciones de ensamble B C 3 3 D 5 5 Perno M15x 60 mm de madera (4 usados en este paso) Tornillo M4 x 50 mm para madera (4 usados en este paso) ③ ⑤ 8. Una el panel inferior (D) a los paneles laterales (B y C) con cuatro pernos de 60 mm de madera (3) y cuatro tornillos para madera de 50 mm (5).
Instrucciones de ensamble 13 13 B J C D Tornillo de M3.5 x 15 mm cabeza especial (14 usados en este paso) ⑬ NOTA: Se recomienda colocar el panel posterior con los tornillos en las esquinas primero. 9. Ahora, volver atrás y apretar todos las tuercas de fijación y tornillos. Asegúrese de que todas las partes estén apretados y que no haya espacios entre las partes. Esto ayudará a mantener el cuadrado de la unidad. 10. Coloque el panel posterior (J) en los bordes posteriores de la unidad ensamblada.
Instrucciones de ensamble 8 7 8 I 7 Manija (2 usados en este paso) Tornillo de manija (4 usados en este paso) ⑦ ⑧ 11. Fije las manijas (7) hacia el exterior del panel de la puerta (I) con cuatro tornillos para manija (8).
Instrucciones de ensamble I B B I 1 2 B I 12. Poner la unidad en posición vertical. 13. Levante la puerta (I) y una los brazos extendidos de bisagra a las bases de bisagra instaladas en el panel lateral izquierdo (B). Aflojar el tornillo en la parte posterior de la articulación de base para tener un ajuste fácil. Alinear e insertar la ranura "U" de la bisagra del brazo bajo la cabeza del tornillo en la parte posterior de la base. Asegúrese de que las bisagras de las puertas funcionan correctamente.
Instrucciones de ensamble B/C 6 C B K F/K K 6 B/C F Soporte de repisa (12 usados en este paso) ⑥ 15. Inserte los soportes de repisa (6) en los orificios deseados en los lados de los compartimentos. Asegúrese de colocar los cuatro soportes de repisa en el mismo nivel por lo que la repisa no quede inclinada. Inclinar y descansar las repisas ajustables (F y K) sobre los soportes de repisa (6) con las muescas en el extremo de la repisa para que siente bien la misma en forma adecuada.
Instrucciones de ensamble 12 C B 11 I I Tapa de tuerca (4 usados en este paso) Tope plástico (1 usado en este paso) ⑫ ⑪ 16. Despegue el tope plástico (11) y pegarlo en la esquina exterior de la puerta (I) donde entra en contacto con el tope de la puerta (10). 17. Conecte las tapas de tuerca de fijación (12) en aquellos que esten visibles para ocultarlas.
Instrucciones de ensamble 18. Posicionar la unidad en el lugar deseado cerca de la pared. 19. Siga las instrucciones impresas en la bolsa de plástico que contiene el juego de restricción de movimiento para unir las restricciones vuelco a la unidad y la pared. NOTA: El juego de restricción de movimiento suministrado es para la construcción de paredes de tablaroca. Será necesario taladrar agujeros para los anclajes de pared.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.