LOT NUMBER: DATE PURCHASED: / / Steele Organizer with Drawers Stock # BH46-084-099-54 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOGUE: Steele Organizer with Drawers (BH46-084-099-54) MADE IN CHINA MAXIMUM LOAD 200 lb. (90.7 kg) MAXIMUM LOAD 50 lb. (22.6 kg) MAXIMUM LOAD 30 lb. (13.6 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. SPECIAL NOTE Please read the instruction sheets completely before assembly.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X 4 FINAL X CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) D- Bottom Panel (Qty. 1) G- Upper Divider Panel (Qty. 2) J- Bottom Long Support (Qty. 2) M- Drawer Left Side (Qty.2) P- Drawer Bottom Panel (Qty.2) B- Left Side Panel (Qty. 1) E- Upper Fixed Shelf (Qty. 1) H- Drawer Divider (Qty. 1) K- Bottom Short Support (Qty. 2) N- Drawer Right Side (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Small Cam Lock (Qty. 12+1 extra) (4) M15 x 60 mm Large Wood Dowel (Qty. 8+1 extra) (7) M6 x 30 mm Wood Dowel (Qty. 4+1 extra) (10) Flat Washer (Qty. 8+1 extra) (13) Handle (Qty. 2) (16) Plastic Cap (Qty. 4+1 extra) (2) Large Cam Lock (Qty. 22+1 extra) (3) Cam Bolt (Qty. 34+1 extra) (5) M8 x 60 mm Small Wood Dowel (Qty.
Assembly Instructions 1 7 N Q M 3 3 3 3 3 R R Small Cam Lock (6 used in this step) Cam Bolt (6 used in this step) ③ ① M6 x 30 mm Wood Dowel (2 used in this step) ⑦ 1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw 6 Cam Bolts (3) into the designated small holes on one Drawer Front (R). 3.
Assembly Instructions P N Q M R 5. Slide the Utility Drawer Bottom Panel (P) into the grooves between the Drawer Side Panels (M and N) until fully inserted into the Drawer Front (R).
Assembly Instructions O 11 11 Q O N N P M R 11 M R M4 x 38 mm Screw (6 used in this step) ⑪ 6. Fasten one Drawer Back Panel (O) to the Drawer Side Panels (M and N) and Bottom Support (Q) with six 38 mm Screws (11). Make sure that Drawer Bottom Panel (P) fits securely into the groove of the Drawer Back Panel (O). Tighten all the screws with a Phillips screwdriver.
Assembly Instructions 14 14 R R 13 Handle (1 used in this step) Handle Bolt (2 used in this step) ⑬ ⑭ 7. Turn the assembled drawer upright. 8. Attach the Handle (13) to the outside of the Drawer Front (R) with two Handle Bolts (14). 9. Repeat the same process to assemble the other drawer.
Assembly Instructions 6 K 12 6 J 12 12 6 K J 12 6 J K 12 J 6 6 12 6 6 6 12 12 K 6 6 D M8 x 30 mm Wood Dowel (12 used in this step) M4 x 50 mm Screw (12 used in this step) ⑫ ⑥ 10. Attach the Bottom Short Supports (K) between the Bottom Long Supports (J) with four 30 mm Wood Dowels (6). 11. Fasten the previous assembly to the Bottom Panel (D) with eight 30 mm Wood Dowels (6) and twelve 50 mm Screws (12).
Assembly Instructions C B 3 F D Cam Bolt (22 used in this step) ③ 12. Securely screw the Cam Bolts (3) into the designated small holes on the Side Panels (B and C), the Bottom Panel (D) and the Lower Fixed Shelf (F) using a Phillips screwdriver.
Assembly Instructions F 2 6 2 2 6 L 2 Large Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ② ⑥ 13. Attach the Back Panel (L) to the Lower Fixed Shelf (F) with two 30 mm Wood Dowels (6) and four Large Cam Locks (2) (Refer to page 3 on Cam Lock system operation supplement).
Assembly Instructions F 6 2 L H 2 Large Cam Lock (2 used in this step) M8 x 30 mm Wood Dowel (2 used in this step) ② ⑥ 14. Attach the Drawer Divider (H) to the Lower Fixed Shelf (F) with two 30 mm Wood Dowels (6) and two Large Cam Locks (2).
Assembly Instructions I 6 I 12 6 H F 12 L M8 x 30 mm Wood Dowel (4 used in this step) 12 M4 x 50 mm Screw (4 used in this step) ⑫ ⑥ 15. Attach two Middle Divider Panels (I) to the Lower Fixed Shelf (F) with four 30 mm Wood Dowels (6) and four 50 mm Screws (12).
Assembly Instructions G G 5 E 5 I 5 I F H L M8 x 60 mm Small Wood Dowel (8 used in this step) ⑤ 16. Attach two Upper Divider Panels (G) and Upper Fixed Shelf (E) to the assembled Middle Divider Panels (I) with eight 60 mm Small Wood Dowels (5).
Assembly Instructions C 6 2 6 2 6 2 2 E 2 6 B 6 2 F H 2 2 2 L 6 6 Large Cam Lock (12 used in this step) M8 x 30 mm Wood Dowel (10 used in this step) ② ⑥ 17. Attach the Right Side Panel (C) to the Fixed Shelves (E and F) and the Back Panel (L) with five 30 mm Wood Dowels (6) and six Large Cam Locks (2). 18. Repeat the same procedure to attach the Left Right Panel (B) at the opposite end.
Assembly Instructions C 2 F H 6 2 B 2 L 6 2 6 4 Large Cam Lock (4 used in this step) ② 4 6 M8 x 30 mm Wood Dowel (4 used in this step) ⑥ D M15x 60 mm Large Wood Dowel (4 used in this step) ④ 19. Insert four 60 mm Large Wood Dowels (4) into the bottom holes on the Side Panels (B and C) and insert four 30 mm Wood Dowels (6) into the bottom holes on the Drawer Divider (H) and the Back Panel (L).
Assembly Instructions C F H B D 12 10 9 8 2-1/4” Bolt (4 used in this step) ⑧ Lock Washer (4 used in this step) ⑨ Flat Washer (4 used in this step) M4 x 50 mm Screw (2 used in this step) ⑩ ⑫ 20. Secure the Bottom Panel (D) to the Side Panels (B and C) with four 2-1/4” Bolts (8) and four Washers (9 and 10). 21. Fasten the Bottom Panel (D) to the Drawer Divider (H) with two 50 mm Screws (12).
Assembly Instructions M8 x 60 mm Small Wood Dowel (8 used in this step) ⑤ 4 10 9 5 8 16 C A G G B Plastic Cap M15x 60 mm Large Wood Dowel (4 used in this step) (4 used in this step) ⑯ ④ 2-1/4” Bolt (4 used in this step) Lock Washer Flat Washer (4 used in this step) (4 used in this step) ⑨ ⑧ ⑩ 22. Insert eight 60 mm Small Wood Dowels (5) into the top holes of Upper Divider Panels (G) and insert four 60 mm Large Wood Dowels (4) into the top holes on the Side Panels (B and C). 23.
Assembly Instructions E 15 C B N N M 25. Ask for assistance to stand the unit upright. 26. Insert the assembled drawers into the frame. Extend the Ball Bearing Slide Tracks on the Side Panels (B and C) all the way forward (including ball bearing cart). Then align the Slide Runners on the assembled drawer with the Slide Tracks and push the drawer carefully inside until it stops. NOTE: If the drawer does not go in smoothly, please take it out and repeat the step.
Assembly Instructions 28. Position the unit at the desired location against a wall. 29. Follow the instructions printed on the plastic bag containing the tipping restraint hardware to attach the tip-over restraints to the unit and the wall. NOTE: The tipping restraint hardware included is for drywall construction. It will be necessary to drill holes for the wall anchors. Depending upon your wall construction, different anchor hardware may be required.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
LOTE NÚMERO: FECHA COMPRA: / / Organizador Steele con cajones Serie # BH46-084-099-54 ENSAMBLE REQUERIDO POR ADULTO Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a la tienda en que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estandar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMA CARGA RECOMENDADA FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Organizador Steele con cajones (BH46-084-099-54) HECHO EN CHINA MÁXIMA CARGA 200 lb. (90.7 kg) MÁXIMA CARGA 50 lb. (22.6 kg) MÁXIMA CARGA 30 lb. (13.6 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. NOTA ESPECIAL Por favor, lea las hojas de instrucciones completamente antes del ensamble.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 y 5 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma SI ES NECESARIO.
Lista de Partes y Artículos de Ferretería Por favor, lea completamente todas las instrucciones y verifique que todas las piezas mencionadas y el material están presentes antes de comenzar el montaje. A- Panel superior (Cant. 1) D- Panel inferior (Cant. 1) G- Panel divisor superior (Cant. 2) J- Soporte inferiore largo (Cant. 2) M- Lado de cajón izq. (Cant.2) P- Panel inferior de cajón (Cant.2) B- Panel izquierdo (Cant. 1) C- Panel derecho (Cant. 1) E- Repisa superior fija (Cant.
Lista de Partes y Artículos de Ferretería Por favor, lea completamente todas las instrucciones y verifique que todas las piezas mencionadas y el material están presentes antes de comenzar el montaje. (1) Tuerca de fijación chica (Cant. 12+1 extra) (4) Perno M15 x 60 mm de madera (Cant. 8+1 extra) (7) Perno M6 x 30 mm de madera (Cant.4+1 extra) (2) Tuerca de fijación grande (Cant. 22+1 extra) (5) Perno M8 x 60 mm de madera (Cant.16+1 extra) (6) Perno M8 x 30 mm de madera (Cant.
Instrucciones de ensamble 1 7 N Q M 3 3 3 3 3 R R Tuerca de fijación chica (6 usados en este paso) Tornillo de fijación (6 usados en este paso) Perno M6 x 30 mm de madera (2 usados en este paso) ③ ① ⑦ 1. Desempacar la unidad y confirmar que todas las partes estan completas antes de tirar la caja y material de empaque. 2. Fijar 6 tornillos de fijación (3) en los agujeros pequeños designados en el frente de cajón (R). 3.
Instrucciones de ensamble P N Q M R 5. Deslice el panel inferior del cajón de utilidad (P) en las ranuras entre los paneles laterales del cajón (M y N) hasta que esté completamente insertado en el frente del cajón (R).
Instrucciones de ensamble O 11 11 Q O N N P M R M 11 R Tornillo M4 x 38 mm (6 usados en este paso) ⑪ 6. Fijar un panel trasero del cajón (O) en los paneles laterales del cajón (M y N) y el soporte inferior (Q) con seis tornillos de 38 mm (11). Asegúrese de que el panel inferior de cajón (P) encaja perfectamente en la ranura del panel trasero del cajón (O). Apriete todos los tornillos con un destornillador estrella.
Instrucciones de ensamble 14 14 R R 13 Manija (1 usado en este paso) Tornillo de maniija (2 usados en este paso) ⑬ ⑭ 7. Gire el cajón en posición vertical. 8. Adjunte las manijas (13) en la parte exterior del frente de cajón (R) con 2 tornillos de manija (14). 9. Repetir el mismo proceso para montar el otro cajón.
Instrucciones de ensamble 6 K 12 6 J 12 12 6 K J 12 6 J 6 K 12 6 J 6 12 12 6 6 12 K 6 6 D Perno M8 x 30 mm de madera (12 usados en este paso) Tornillo M4 x 50 mm (12 usados en este paso) ⑫ ⑥ 10. Coloque los soportes inferiores cortos (K) entre los soportes inferiores largos (J) con cuatro pernos de 30 mm de madera (6). 11. Sujetar el ensamble anterior al panel inferior (D) con ocho pernos de 30 mm de madera (6) y doce tornillos de 50 mm (12).
Instrucciones de ensamble C B 3 F D Tornillo de fijación (22 usados en este paso) ③ 12. Asegure los tornillos de fijación (3) en los orificios pequeños designados en los paneles laterales (B y C), el panel inferior (D) y la repisa inferior fija (F) con un desarmador estrella.
Instrucciones de ensamble F 2 6 2 2 6 L 2 Tuerca de fijación grande Perno M8 x 30 mm de madera (2 usados en este paso) (4 usados en este paso) ② ⑥ 13. Fijar el panel posterior (L) a la repisa inferior fija (F) con dos pernos de 30 mm de madera (6) y cuatro tuercas de fijación grandes (2) (consulte la página 3 de la tuerca de fijación y su operación).
Instrucciones de ensamble F 6 2 L H 2 Tuerca de fijación grande Perno M8 x 30 mm de madera (2 usados en este paso) (2 usados en este paso) ② ⑥ 14. Una el divisor de cajón (H) para la repisa inferior fija (F) con dos pernos de 30 mm de madera (6) y dos tuercas de fijación grandes (2).
Instrucciones de ensamble I 6 I 12 6 H F 12 L 12 Tornillo M4 x 50 mm (4 usados en este paso) Perno M8 x 30 mm de madera (4 usados en este paso) ⑫ ⑥ 15. Adjuntar 2 divisores medios (I) a la repisa fija inferior (F) con 4 pernos de 30 mm de madera (6) y 4 tornillos de 50 mm (12).
Instrucciones de ensamble G G 5 E 5 I 5 I F H L Perno M8 x 60 mm de madera (8 usados en este paso) ⑤ 16. Coloque dos paneles divisorios superiores (G) y repisa fija superior (E) a los paneles divisorios medios ensamblados (I) con ocho pernos de 60 mm de madera (5).
Instrucciones de ensamble C 6 2 6 2 6 2 2 E 2 6 B 6 2 F H 2 2 2 L 6 6 Tuerca de fijación grande Perno M8 x 30 mm de madera (10 usados en este paso) (12 usados en este paso) ② ⑥ 17. Coloque el panel lateral derecho (C) a las repisas fijas (E y F) y el panel posterior (L) con cinco pernos de 30 mm de madera (6) y seis tuercas de fijación grandes (2). 18. Repita el mismo procedimiento para fijar el panel izquierdo (B) en el extremo opuesto.
Instrucciones de ensamble C 2 F H 6 2 B 2 L 6 2 6 4 Tuerca de fijación grande (4 usados en este paso) ② 4 6 Perno M8 x 30 mm (4 usados en este paso) ⑥ D Perno M15x 60 mm de madera (4 usados en este paso) ④ 19. Inserte cuatro pernos grandes de 60 mm de madera (4) en los orificios inferiores de los paneles laterales (B y C) e inserte cuatro pernos de 30 mm de madera (6) en los orificios inferiores del divisor de cajón (H) y el panel posterior (L).
Instrucciones de ensamble C F H B D 12 10 Tornillo 2-1/4” (4 usados en este paso) 9 8 ⑧ Arandela de presión (4 usados en este paso) ⑨ Arandela plana (4 usados en este paso) Tornillo de M4 x 50 mm (2 usados en este paso) ⑩ ⑫ 20. Fije el panel inferior (D) a los paneles laterales (B y C) con cuatro tornillos de 2-1/4” (8) y cuatro arandelas (9 y 10). 21. Fijar el panel inferior (D) al divisor de cajón (H) con dos tornillos de 50 mm (12).
Instrucciones de ensamble Perno M8 x 60 mm de madera (8 usados en este paso) ⑤ 4 10 9 5 8 16 C A G G B Tapón plástico Perno M15x 60 mm de madera (4 usados en este paso) (4 usados en este paso) ⑯ ④ Arandela de presión Tornillo de 2-1/4” (4 usados en este paso) (4 usados en este paso) ⑨ ⑧ Arandela plana (4 usados en este paso) ⑩ 22.
Instrucciones de ensamble E 15 C B N N M 25. Pedir ayuda a colocar la unidad en posición vertical. 26. Introducir el cajón montado en el bastidor. Extender el carrito con baleros de las correderas de los paneles laterales (B y C) completamente hacia adelante (incluyendo el carrito interior). Alinee los complementos de correderas del cajón ensamblado con las de la unidad y empuje el cajón con cuidado en el interior hasta que se detenga.
Instrucciones de ensamble 28. Posición de la unidad en la posición deseada contra una pared. 29. Siga las instrucciones impresas en la bolsa de plástico que contiene el hardware de la restricción de inflexión para unir las restricciones vuelco a la unidad y la pared. NOTA: El juego de restricción de movimiento suministrado es para paredes de tablaroca. Será necesario taladrar agujeros para los taquetes de pared.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.