LOT NUMBER: DATE PURCHASED: / / Lana Modern Writing Desk Stock # BH48-084-099-04 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Lana Modern Writing Desk MODEL # BH48-084-099-04 MADE IN CHINA MAXIMUM LOAD 200 lb. (90.8 kg) MAXIMUM LOAD 10 lb. (4.5 kg) MAXIMUM LOAD 20 lb. (9.1 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. SPECIAL NOTE Please read the instruction sheets completely before assembly.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4, 5 and 6 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X X 4 FINAL CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Back Panel (Qty. 1) C-Left Side Panel (Qty. 1) D- Right Side Panel (Qty. 1) E- Left Partition Panel (Qty. 1) F- Right Partition Panel (Qty. 1) G- Middle Stretcher (Qty. 1) H- Middle Crossbar (Qty. 1) I- Left Bottom Panel (Qty. 1) J- Right Bottom Panel (Qty. 1) K- Leg (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. L- Small Drawer Front Panel (Qty. 2) O- Small Drawer Back Panel (Qty. 2) R- Large Drawer Left Side Panel (Qty. 1) M- Small Drawer Left Side Panel (Qty. 2) P- Small Drawer Bottom Panel (Qty. 2) S- Large Drawer Right Side Panel (Qty. 1) U- Large Drawer Bottom Panel (Qty. 1) N- Small Drawer Right Side Panel (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Cam Lock (Qty. 42+2 extra) (2) Cam Bolt (Qty. 42+2 extra) (4) M4 x 38 mm Screw (Qty. 12+1 extra) (7) 21mm Handle Bolt (Qty. 2+1 extra) Hex Wrench (Qty. 1) (5) M4 x 50 mm Screw (Qty. 12+1 extra) (8) 1/4” x 40 mm Bolt (Qty. 8+1 extra) Glue (Qty. 2) (3) M8 x 30 mm Wood Dowel (Qty. 56+2 extra) (6) Handle with Back Plate (Qty.
Assembly Instructions x2 L Cam Bolt (4 used in this step) ② 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on one Small Drawer Front Panel (L) with a Phillips screwdriver.
Assembly Instructions M O 4 3 x2 N 3 4 M4 x 38 mm Screw (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ④ ③ 3. Insert four 30 mm Wood Dowels (3) into the inner holes on one Small Drawer Back Panel (O) as a guide. Tap it in with a rubber mallet, if necessary. Make sure that you use a small amount of glue with both ends of all dowels. NOTE: It is very important to use a small amount of glue on both ends of dowels. 4.
Assembly Instructions P M x2 N O 5. Slide one Small Drawer Bottom Panel (P) into the grooves between the Small Drawer Side Panels (M and N) until fully inserted into the groove of the Small Drawer Back Panel (O).
Assembly Instructions L P M x2 N Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 6. Attach one Small Drawer Front Panel (L) to the Small Drawer Side Panels (M and N) and fasten them in place with four 30 mm Wood Dowels (3) and four Cam Locks (1). 7. Repeat the same procedure to assemble the other Small Drawer.
Assembly Instructions Q T Cam Bolt (6 used in this step) ② 8. Securely screw the Cam Bolts (2) into the designated small holes on the Large Drawer Front Panel and Back Panels (Q and T) with a Phillips screwdriver.
Assembly Instructions R V S Q 9. Cam Lock (5 used in this step) M8 x 30 mm Wood Dowel (1 used in this step) ① ③ Attach the Large Drawer Left and Right Side Panels (R and S) to the Large Drawer Front Panel (Q) with four Cam Locks (1). 10. Attach the Large Drawer Bottom Support (V) to the Large Drawer Front Panel (Q) with one 30 mm Wood Dowel (3) and one Cam Lock (1).
Assembly Instructions U R V S Q 11. Slide the Large Drawer Bottom Panel (U) into the grooves between the Large Drawer Side Panels (R and S) until fully inserted into the groove of the Large Drawer Front Panel (Q).
Assembly Instructions T V U Cam Lock (1 used in this step) M8 x 30 mm Wood Dowel (1 used in this step) ① ③ 12. Attach the Large Drawer Back Panel (T) to the Large Drawer Bottom Support (V) with one 30 mm Wood Dowel (3) and one Cam Lock (1). Make sure that the Large Drawer Back Panel (T) fits securely into the Large Drawer Bottom Panel (U).
Assembly Instructions R T S M4 x 38 mm Screw (4 used in this step) ④ 13. Fasten the Large Drawer Back Panel (T) to the Large Drawer Side Panels (R and S) with four 38 mm Screws (4).
Assembly Instructions 7 6 Q Handle with Back Plate (1 used in this step) 21mm Handle Bolt (2 used in this step) ⑦ ⑥ 14. Attach the Handle with Back Plate (6) to the outside of the Large Drawer Front Panel (Q) with two 21mm Handle Bolts (7).
Assembly Instructions A B F E D C Cam Bolt (28 used in this step) ② 15. Securely screw the Cam Bolts (2) into the designated small holes on the Panels (A, B, C, D, E and F) with a Phillips screwdriver.
Assembly Instructions 3 1 E G H F Cam Lock (6 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 16. Attach the Middle Stretcher (G) and Middle Crossbar (H) between the Partition Panels (E and F) with six Cam Locks (1) and four 30 mm Wood Dowels (3).
Assembly Instructions 3 B E F 1 Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ③ ① 17. Attach the Back Panel (B) to the Partition Panels (E and F) with four Cam Locks (1) and four 30 mm Wood Dowels (3).
Assembly Instructions 3 C 1 B D Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 18. Attach the Side Panels (C and D) to the Back Panel (B) with four Cam Locks (1) and four 30 mm Wood Dowels (3).
Assembly Instructions C E B 1 G 3 F D A Cam Lock (14 used in this step) M8 x 30 mm Wood Dowel (14 used in this step) ① ③ 19. Attach the previous assembly to the Top Panel (A) with fourteen Cam Locks (1) and fourteen 30 mm Wood Dowels (3).
Assembly Instructions 5 5 I 5 5 3 3 J 3 B 3 C E 3 3 F D M4 x 50 mm Screw (12 used in this step) M8 x 30 mm Wood Dowel (12 used in this step) ③ ⑤ 20. Attach the Left and Right Bottom Panels (I and J) to the previous assembly with twelve 30 mm Wood Dowels (3) and twelve 50 mm Screws (5). Go back and tighten all the cam locks and screws.
Assembly Instructions 8 9 10 K 8 9 10 K I J 1/4" x 40 mm Bolt (8 used in this step) Lock Washer (8 used in this step) Flat Washer (8 used in this step) ⑨ ⑩ ⑧ 21. Attach the Legs (K) to the Bottom Panels (I and J) with eight 40 mm Bolts (8) and eight Washers (9 and 10). DO NOT over tighten the bolts.
Assembly Instructions 22. Ask for assistance to stand the unit upright and position at the desired location. 23. Insert the assembled drawers into the frame. Extend the Ball Bearing Slide Tracks on the Side Panels (C, D, E and F) all the way forward (including ball bearing cart). Then align the slide runners on the drawer side panels with the slide tracks and push the drawer carefully inside until it stops. NOTE: If a drawer does not go in smoothly, please take it out and repeat the step.
Assembly Instructions 24. If necessary, adjust the pre-attached floor levelers at the bottom of Legs (K) to level the unit.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO DEL LOTE: FECHA DE COMPRA / / Moderno Escritorio Lana Serie # BH48-084-099-04 ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Moderno Escritorio Lana MODELO # BH48-084-099-04 HECHO EN CHINA CARGA MÁXIMA 200 lb. (90.8 kg) CARGA MÁXIMA 10 lb. (4.5 kg) CARGA MÁXIMA 20 lb. (9.1 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRÍA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. NOTA ESPECIAL Lea atentamente toda la hoja de instrucciones antes de comenzar el montaje.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4, 5 y 6 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma, SI ES NECESARIO.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y ferretería indicadas se encuentran presentes antes del comienzo del montaje. A- Módulo superior (Cant. 1) B- Módulo trasero (Cant. 1) D- Módulo lateral derecho (Cant. 1) E- Módulo divisor izquierdo (Cant. 1) G- Bastidor central (Cant. 1) H- Larguero central (Cant. 1) J- Módulo inferior derecho (Cant. 1) C- Módulo lateral izquierdo (Cant. 1) F- Módulo divisor derecho (Cant.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y ferretería indicadas se encuentran presentes antes del comienzo del montaje. L- Panel frontal del cajón pequeño (Cant. 2) O- Módulo trasero del cajón pequeño (Cant. 2) R- Módulo lateral izquierdo del cajón grande (Cant. 1) M- Módulo lateral izquierdo del cajón pequeño (Cant. 2) P- Módulo inferior del cajón pequeño (Cant. 2) Q- Módulo frontal del cajón grande (Cant.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y ferretería indicadas se encuentran presentes antes del comienzo del montaje. (1) Tuerca de fijación (Cant. 42+2 extra) (2) Perno de fijación (Cant. 42+2 extra) (4) M4 x 38 mm Tornillo (Cant. 12+1 extra) (5) M4 x 50 mm Tornillo (Cant. 12+1 extra) (7) 21 mm Perno de manija (Cant. 2+1 extra) Llave hexagonal (Cant. 1) (8) Perno de 1/4” x 40 mm (Cant. 8+1 extra) Pegamento (Cant.
Instrucciones de ensamble x2 L Perno de fijación (4 utilizados en este paso) ② 1. Desembale la unidad y confirme que cuenta con todo el equipo y partes necesarias. Monte la unidad sobre un suelo con alfombra o el cartón de embalaje vacío para evitar cualquier arañazo. 2. Fije firmemente los pernos de fijación (2) en los pequeños agujeros designados en uno de los módulos frontales del cajón pequeño (L) utilizando un desarmador estrella.
Instrucciones de ensamble M O 4 3 x2 N 3 4 M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ④ ③ 3. M4 x 38 mm Tornillo (4 utilizados en este paso) Introduzca cuatro espigas de madera de 30 mm (3) en los agujeros interiores de uno de los módulos traseros del cajón pequeño (O) como guía. Encájelos con la maza de goma si fuera necesario. Asegúrese de que utiliza una pequeña cantidad de pegamento en ambos extremos de todas las espigas.
Instrucciones de ensamble P M x2 N O 5. Deslice el módulo inferior del cajón pequeño (P) en las ranuras entre los módulos laterales del cajón pequeño (M y N) hasta insertarlo completamente en la ranura del módulo trasero del cajón pequeño (O).
Instrucciones de ensamble L P M x2 N Tuerca de fijación (4 utilizadas en este paso) M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ① ③ 6. Fije un módulo frontal del cajón pequeño (L) a los módulos laterales del cajón pequeño (M y N) y fíjelos con cuatro espigas de madera de 30 mm (3) y cuatro tuercas de fijación (1). 7. Repita el mismo procedimiento para montar el otro cajón pequeño.
Instrucciones de ensamble Q T Perno de fijación (6 utilizados en este paso) ② 8. Fije firmemente los pernos de fijación (2) en los pequeños agujeros designados en el módulo frontal y trasero del cajón grande (Q y T) con un desarmador estrella.
Instrucciones de ensamble R V S Q M8 x 30 mm Espiga de madera (1 utilizada en este paso) Tuerca de fijación (5 utilizadas en este paso) ③ ① 9. Una los módulos laterales izquierdo y derecho del cajón grande (R y S) al módulo frontal del cajón grande (Q) con cuatro tuercas de fijación (1). 10. Una el soporte inferior del cajón grande (V) al módulo frontal del cajón grande (Q) con una espiga de madera de 30 mm (3) y una tuerca de fijación (1).
Instrucciones de ensamble U R V S Q 11. Deslice el módulo inferior del cajón grande entre las ranuras de los módulos laterales del cajón grande (R y S) hasta su completa inserción en la ranura del módulo frontal del cajón grande (Q).
Instrucciones de ensamble T V U Tuerca de fijación (1 utilizada en este paso) M8 x 30 mm Espiga de madera (1 utilizada en este paso) ③ ① 12. Fije el módulo trasero del cajón grande (T) al soporte inferior del cajón grande (V) con una espiga de madera de 30 mm (3) y una tuerca de fijación (1). Asegúrese de que el módulo trasero del cajón grande (T) encaje firmemente en el módulo inferior del cajón grande (U).
Instrucciones de ensamble R T S M4 x 38 mm Tornillo (4 utilizados en este paso) ④ 13. Fije el módulo trasero del cajón grande (T) a los módulos laterales del cajón grande (R y S) con cuatro tornillos de 38 mm (4).
Instrucciones de ensamble 7 6 Q Manija y placa posterior (1 utilizado en este paso) 21mm Perno de manija (2 utilizados en este paso) ⑦ ⑥ 14. Fije la manija y placa posterior (6) a la parte exterior del módulo frontal del cajón grande (Q) con dos 21mm pernos de manija (7).
Instrucciones de ensamble A B F E D C Perno de fijación (28 utilizados en este paso) ② 15. Fije firmemente los pernos de fijación (2) en los pequeños agujeros designados en los módulos (A, B, C, D, E y F) con un desarmador estrella.
Instrucciones de ensamble 3 1 E G H F Tuerca de fijación (6 utilizadas en este paso) M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ③ ① 16. Fije el bastidor central (G) y el larguero central (H) entre los módulos divisores (E y F) con seis tuercas de fijación (1) y cuatro espigas de madera de 30 mm (3).
Instrucciones de ensamble 3 B E F 1 Tuerca de fijación (4 utilizadas en este paso) M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ① ③ 17. Una el módulo trasero (B) a los módulos divisores (E y F) con cuatro tuercas de fijación (1) y cuatro espigas de madera de 30 mm (3).
Instrucciones de ensamble 3 C 1 B D Tuerca de fijación (4 utilizadas en este paso) M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ③ ① 18. Fije los módulos laterales (C y D) al módulo trasero (B) con cuatro tuercas de fijación (1) y cuatro espigas de madera de 30 mm (3).
Instrucciones de ensamble C E B 1 G 3 F D A Tuerca de fijación (14 utilizadas en este paso) M8 x 30 mm Espiga de madera (14 utilizadas en este paso) ③ ① 19. Fije el ensamble previo al módulo superior (A) con catorce tuercas de fijación (1) y catorce espigas de madera de 30 mm (3).
Instrucciones de ensamble 5 5 I 5 5 3 3 J 3 B 3 C E 3 3 F D M4 x 50 mm Tornillo (12 utilizados en este paso) M8 x 30 mm Espiga de madera (12 utilizadas en este paso) ③ ⑤ 20. Una los módulos inferiores izquierdo y derecho (I y J) al montaje anterior con doce espigas de madera de 30 mm (3) y doce tornillos de 50 mm (5). Revíselo y fije todas las tuercas de fijación y tornillos.
Instrucciones de ensamble 8 9 10 K 8 9 10 K I J Perno 1/4" x 40 mm (8 utilizados en este paso) Arandela de seguridad (8 utilizadas en este paso) ⑧ ⑨ Arandela plana (8 utilizadas en este paso) ⑩ 21. Fije las patas (K) a los módulos inferiores (I y J) con ocho pernos de 40 mm (8) y ocho arandelas (9 y 10). NO apriete en exceso los tornillos.
Instrucciones de ensamble 22. Pedir asistencia para posicionar la unidad ensamblada en posición vertical y en el lugar deseado. 23. Insertar el los cajones ensamblados en el marco. Extender los rieles de la corredera de baleros en los paneles laterales (C, D, E y F) todo el camino hacia enfrente (incluyendo el carrito de baleros). Luego alinear los complementos de correderas en los paneles laterales del cajón con los carriles de corredera y empujar el cajón hasta que tope.
Instrucciones de ensamble 24. Si fuera necesario, ajuste los niveladores de piso prefijados en la parte inferior del patas (K).
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayones. Uso de cera para pulir muebles no es necesario. Si desea usar cera, pruébela en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los ponga sobre la unidad.