LOT NUMBER: DATE PURCHASED: / / Ellis Shutter Bookcase Cabinet Stock # BH48-084-099-12 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Ellis Shutter Bookcase Cabinet MODEL # BH48-084-099-12 MADE IN CHINA MAXIMUM LOAD 50 lb. (22.7 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. How to adjust the European adjustable hinges on doors Shipping may cause doors to go out of alignment.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X X 4 FINAL CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 2) C- Bottom Panel (Qty. 1) D- Top Stretcher (Qty. 2) E- Base Front Stretcher (Qty. 1) F- Base Back Stretcher (Qty. 1) G- Base Side Stretcher (Qty. 2) H- Adjustable Shelf (Qty. 3) I- Left Side Panel (Qty. 1) J- Right Side Panel (Qty. 1) K- Left Door (Qty. 1) L- Right Door (Qty.
Assembly Instructions Cam Bolt (26 used in this step) ② 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on the Panels (A, C, I and J) and the Bottom Stretchers (E and F) using a Phillips screwdriver.
Assembly Instructions 4 4 4 3 4 D 4 4 D 3 3 4 3 M8 x 30 mm Wood Dowel (4 used in this step) M4 x 32 mm Screw (10 used in this step) ④ ③ 3. Glue four Wood Dowels (3) into the inner holes of the Top Stretchers (D) and attach them to the Top Panel (A) with ten 32 mm Wood Screws (4).
Assembly Instructions UP I UP B B 3 1 Cam Lock (8 used in this step) M8 x 30 mm Wood Dowel (8 used in this step) ① ③ 4. Attach two Fixed Shelves (B) between the Side Panels (I and J) with eight Wood Dowels (3) and eight Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
Assembly Instructions 3 1 A I B B J Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 5. Attach the Top Panel assembly to the top of Side Panels (I and J) with four Wood Dowels (3) and four Cam Locks (1).
Assembly Instructions F G 3 1 1 1 1 3 3 E G 3 Cam Lock (4 used in this step) M8 x 30 mm Wood Dowel (4 used in this step) ① ③ 6. Combine the Base Front Stretcher (E), Back Stretcher (F) and Side Stretchers (G) together with four Wood Dowels (3) and four Cam Locks (1).
Assembly Instructions G F E 1 G 3 C Cam Lock (10 used in this step) M8 x 30 mm Wood Dowel (8 used in this step) ① ③ 7. Attach the assembled base to the Bottom Panel (C) with the Wood Dowels (3) and the Cam Locks (1).
Assembly Instructions I J 3 3 5 C E 5 M8 x 30 mm Wood Dowel (4 used in this step) M4 x 50 mm Screw (4 used in this step) ⑤ ③ 8. Attach the assembled base to the Side Panels (I and J) with four Wood Dowels (3) and four 50 mm Screws (5).
Assembly Instructions 6 UP M J C M M3.5 x 15 mm Washer Head Screw (32 used in this step) ⑥ 9. Now, go back and tighten all Cam Locks and Screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 10. Unfold the Back Panel (M) and position it onto the back edges of the assembly. Make sure that the overlaps on the panels are even all the way around. Secure the Back Panel (M) in place with the 15 mm Washer Head Screws (6).
Assembly Instructions I/J H J 9 I H H 9 H Shelf Support (8 used in this step) ⑨ 11. Stand the unit upright. 12. Insert the Shelf Supports (9) into the desired holes on the side panels (I and J). Make sure you place the four Shelf Supports in the same level so the shelf is not tilted. Tilt and rest the Adjustable Shelves (H) onto the Shelf Supports (9).
Assembly Instructions 8 7 K 8 7 L Handle (2 used in this step) 32mm Handle Bolt (4 used in this step) ⑦ ⑧ 13. Attach the Handle (7) to the front of each Door (K and L) with two 32mm Handle Bolts (8).
Assembly Instructions K/L I/J J K/L I/J 1 I K/L L 10 K 10 Rubber Bumper (4 used in this step) ⑩ 14. Pick up the Right Door (L) and attach the extended Hinge Arms to the Hinge Bases installed on Right Side Panel (J). Loosen the bolt on the back of Hinge Base for a comfortable fit. Align and insert the “U” slot on Hinge Arm under the bolt head on the back of Hinge Base. Make sure that both door hinges engage and function properly. Tighten the bolt on the Hinge Base to lock the hinges in place. 15.
Assembly Instructions Tools required (not provided): Phillips screwdriver, stud finder, power drill and 3 mm/0.1 in drill bit. 18. Ask for assistance to position the unit at the desired location against a wall. If necessary, adjust the preattached floor levelers at the bottom of the Base Front Stretcher (E) to level the unit. 19. Follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to attach the tip-over restraints to the unit and the wall.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO DEL LOTE: FECHA DE COMPRA / / Gabinete Ellis tipo librero con persianas Serie # BH48-084-099-12 ENSAMBLE REQUERIDO POR ADULTOS Si tiene alguna pregunta relacionada con el montaje o si faltan piezas, NO devuelva este producto al establecimiento donde lo adquirió.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Gabinete Ellis tipo librero con persianas MODELO # BH48-084-099-12 HECHO EN CHINA CARGA MÁXIMA 50 lb. (22.7 kg) ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES. Como ajustar las bisagras Europeas ajustables en las puertas El envio puede causar que las puertas se desalineen.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma, SI ES NECESARIO.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y herramientas indicadas se encuentran presentes antes del comienzo del montaje. A- Módulo superior (Cant. 1) B- Balda fija (Cant. 2) D- Bastidor superior (Cant. 2) E- Bastidor frontal de la base (Cant. 1) G- Bastidor lateral de la base (Cant. 2) H- Balda ajustable (Cant. 3) J- Módulo lateral derecho (Cant. 1) C- Módulo inferior (Cant. 1) F- Bastidor trasero de la base (Cant.
Instrucciones de ensamblaje Perno (26 utilizados en este paso) ② 1. Desembale la unidad y confirme que cuenta con todo el equipo y partes necesarias. Monte la unidad sobre un suelo con alfombra o el cartón de embalaje vacío para evitar cualquier arañazo. 2. Atornille firmemente los pernos (2) en los agujeros pequeños designados en los módulos (A, C, I y J) y a los bastidores inferiores (E y F) utilizando un destornillador Phillips.
Instrucciones de ensamblaje 4 4 4 3 4 D 4 4 D 3 3 4 3 M8 x 30 mm Espiga de madera (4 utilizadas en este paso) M4 x 32 mm Tornillo (10 utilizados en este paso) ④ ③ 3. Pegue cuatro espigas de madera (3) en los agujeros internos de los bastidores superiores (D) y fíjelas al módulo superior (A) con diez tornillos de madera de 32 mm (4).
Instrucciones de ensamblaje UP I UP B B 3 1 Leva de fijación (8 utilizadas en este paso) M8 x 30 mm Espiga de madera (8 utilizadas en este paso) ① ③ 4. Unas dos baldas fijas (B) entre los módulos laterales (I y J) con ocho espigas de madera (3) y ocho levas de fijación (1) (Consulte la página 3 del suplemento sobre uso del sistema de levas de fijación).
Instrucciones de ensamblaje 3 1 A I B B J Leva de fijación (4 utilizadas en este paso) M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ① ③ 5. Fije el montaje del módulo superior a los módulos laterales superiores (L y J) con cuatro espigas de madera (3) y cuatro levas de fijación (1).
Instrucciones de ensamblaje F G 3 1 1 1 1 3 3 E G 3 Leva de fijación (4 utilizadas en este paso) M8 x 30 mm Espiga de madera (4 utilizadas en este paso) ① ③ 6. Una el bastidor frontal de la base (E), el bastidor trasero (F) y los bastidores laterales (G) entre sí con cuatro espigas de madera (3) y cuatro levas de fijación (1).
Instrucciones de ensamblaje G F E 1 G 3 C Leva de fijación (10 utilizadas en este paso) M8 x 30 mm Espiga de madera (8 utilizadas en este paso) ① ③ 7. Una la base ya montada al módulo inferior (C) con las espigas de madera (3) y las levas de fijación (1).
Instrucciones de ensamblaje I J 3 3 5 C E 5 M8 x 30 mm Espiga de madera (4 utilizadas en este paso) M4 x 50 mm Tornillo (4 utilizados en este paso) ⑤ ③ 8. Una la base ya montada a los módulos laterales (I y J) con cuatro espigas de madera (3) y cuatro tornillos de 50 mm (5).
Instrucciones de ensamblaje 6 UP M J C M M3.5 x 15 mm Tornillo con arandela (32 utilizados en este paso) ⑥ 9. Ahora, revise y asegure todas las levas de fijación y tornillos. Asegúrese de que todos los componentes estén fijados y no queden huecos entre las partes. Esto ayudará a mantener la integridad de la unidad. 10. Desdoble el modulo trasero (M) y sitúelo en los bordes traseros del montaje. Asegúrese de que los solapamientos entre los módulos son uniformes a lo largo del montaje.
Instrucciones de ensamblaje I/J H J 9 I H H 9 H Soporte de balda (8 utilizados en este paso) ⑨ 11. Levante la unidad. 12. Inserte los soportes de la balda (9) en los agujeros deseados en los módulos laterales (I y J). Asegúrese de que sitúa los cuatro soportes de balda a la misma altura, para que la balda no quede ladeada. Incline y coloque las baldas ajustables (H) en los soportes de balda (9).
Instrucciones de ensamblaje 8 7 K 8 7 L Tirador (2 utilizados en este paso) 32mm Perno (4 utilizados en este paso) ⑦ ⑧ 13. Una el tirador (7) al frontal de cada puerta (K y L) con dos 32mm pernos (8).
Instrucciones de ensamblaje K/L I/J J K/L I/J 1 I K/L L 10 K 10 Tope de goma (4 utilizados en este paso) ⑩ 14. Coja la puerta derecha (L) y una las bisagras a las bases de bisagra instaladas en el módulo lateral derecho (J). Afloje el perno en la parte trasera de la bisagra para que se ajuste cómodamente. Alinee e inserte las ranuras en “U” de las bisagras bajo la cabeza del perno en la parte trasera de la base de la bisagra.
Instrucciones de ensamblaje Herramientas necesarias (no incluidas): Desarmador estrella, detector de vigas, taladro eléctrico y taladro de 3mm (0.1"). 18. Pida ayuda para colocar la unidad contra la pared en la posición deseada. Si fuera necesario, ajuste los niveladores de piso prefijados en la parte inferior del bastidor frontal de la base (E). 19. Siga las instrucciones impresas en la bolsa de plástico que contiene el kit anti-volcado para colocar los protectores anti-volcado en la unidad y la pared.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayones. El uso de cera para pulir muebles no es necesario. Si desea usar cera pruebe en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que puede dañar el acabado. Siempre utilice protección para vasos cuando los coloque sobre la unidad.