LOT NUMBER: DATE PURCHASED: / / Canton Media Console MODEL # BHS0025004002 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Canton Media Console MODEL # BHS0025004002 FITS UP TO MOST 177.8 cm / 70” DIAGONAL FLAT PANEL TVs MAXIMUM LOAD 61.2 kg / 135 lb PLACE TV BEHIND THE STOPPER MAXIMUM LOAD 22.7 kg / 50 lb THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT.
Important Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY. 1 2 3 X X 4 FINAL CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) D- Left Partition Panel (Qty. 1) G- Bottom Panel (Qty. 1) J- Door (Qty. 2) B- Left Side Panel (Qty. 1) E- Right Partition Panel (Qty. 1) H- Bottom Front Stretcher (Qty. 1) K- Small Adjustable Shelf (Qty. 4) M- Back Panel (Qty. 1) C- Right Side Panel (Qty. 1) F- Middle Stile (Qty. 2) I- Bottom Back Stretcher (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Cam Lock (Qty. 27+1 extra) (2) Cam Bolt (Qty. 27+1 extra) (3) M8 x 30 mm Wood Dowel (Qty. 26+1 extra) (4) M4 x 50 mm Screw (Qty. 4+1 extra) (5) M3.5 x 15 mm Pan Head Screw (Qty. 8+1 extra) (7) Floor leveler (Qty. 2) (8) M3.5 x 15 mm Washer Head Screw (Qty. 24+1 extra) (10) Shelf Support (Qty. 24+1 extra) (11) M3.
Assembly Instructions C B F F G 2 ② x 19 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on the Side Panels (B and C), the Bottom Panel (G) and the Middle Stiles (F) using a Phillips screwdriver.
Assembly Instructions D 3 3 E 3 3 ③x4 3. Glue the 30 mm Wood Dowels (3) into side holes of the Partition Panels (D and E).
Assembly Instructions F D 1 ① x3 4. Align and attach one Middle Stile (F) to the Left Partition Panel (D) by engaging 3 Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
Assembly Instructions F E 1 ② x3 5. Repeat the same procedure to combine the other Middle Stile (F) to the Right Partition Panel (E).
Assembly Instructions 3 3 G 3 3 E 3 3 3 3 3 3 3 D 3 3 3 I 3 3 H 3 3 ③ x 18 6. Glue the 30 mm Wood Dowels (3) into side holes of Bottom Panel (G), Partition Panels (D and E) and Bottom Stretchers (H and I).
Assembly Instructions 1 G I G ①x3 7. Align and attach the Bottom Back Stretcher (I) to the Bottom Panel (G) by engaging 3 Cam Locks (1).
Assembly Instructions 1 G H G I ①x4 8. Align and attach the Bottom Front Stretcher (H) to the Bottom Panel (G) by engaging 4 Cam Locks (1).
Assembly Instructions E D H 4 G 4 4 I 4 ④x4 9. Attach the Partition Panels (D and E) to the Bottom Panel (G) with four 50 mm Wood Screws (4).
Assembly Instructions B 3 3 C 3 3 ③x4 10. Glue the 30 mm Wood Dowels (3) into side holes of the Side Panels (B and C).
Assembly Instructions C E B/C D G G 1 B ①x6 11. Align the large holes on Left Side Panel (B) with the inserted Wood Dowels (3) on the assembled base. Firmly press them together and fasten it in place by engaging 3 Cam Locks (1). 12. Repeat the previous step to attach Right Side Panel (C) at the other end.
Assembly Instructions 2 A ②x8 13. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) using a Phillips screwdriver.
Assembly Instructions A 11 11 9 A x4 ⑨x2 14. Using the pilot holes as a guide, fasten 2 door stoppers (9) to the Top Panel (A) with four 15 mm Flat Head Screws (11).
Assembly Instructions 1 A C E D G B ①x8 15. Ask for assistance to position the Top Panel (A) onto the inserted Wood Dowels (3). Attach the Top Panel (A) in place by engaging 8 Cam Locks (1).
Assembly Instructions C A E D G B 6 5 ⑤x8 ⑥x2 16. With the pilot holes as a guide, align and attach two Triangle Metal Plates (6) to the front corners of the assembled base, using four 15 mm Pan Head Screws (5) per bracket.
Assembly Instructions C A E D G B 7 ⑦x2 17. Screw two Floor Levelers (7) into the threaded sockets on the Triangle Metal Plates (6) and set to the correct height.
Assembly Instructions 8 8 M G C ⑧ x 24 18. Now, go back and tighten all Cam Locks and Screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 19. Flip the assembled unit around at its front edges. Unfold the Back Panel (M) and position it onto the back edges of the assembly. Make sure that the overlaps on the panels are even all the way around. Secure the Back Panel (M) in place with the 15 mm Washer Head Screws (8).
Assembly Instructions 15 15 15 15 14 14 J x2 x4 x8 20. Extend the Hinges Arms (14) and rest the Hinge Cups onto the cutouts of the Door Panels (J). Secure the Hinge Arms in place by using two 15 mm Zinc Screws (15) in each.
Assembly Instructions A C B J 14 J B/C 15 x 16 21. Stand the unit upright. 22. Using the pilot holes as a guide, pick up one Door (J) and fasten the hinge bases onto the Left Side Panel (B) with four 15 mm Zinc Screws (15) in each. DO NOT fully tighten the screws. 23. Repeat the procedure to attach the other Door (J) to the Right Side Panel (C). 24. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the screws for a good fit.
Assembly Instructions A C 12 13 B 13 J 12 J x2 x2 25. Attach one Knob (12) to the front side of each Door (J) with the provided Knob Bolts (13).
Assembly Instructions A C L/K 10 11 B L K K L K K x 24 ⑩ x 24 26. Insert four Shelf Supports (10) into the holes at your desired height inside each side compartment. Make sure you place the four Shelf Supports (10) in the same level so the shelf is not tilted. Tilt and rest the Adjustable Shelves (K and L) onto the Shelf Supports (10). Secure the shelf in place with the 15 mm Flat Head Screw (11) for extra support.
Assembly Instructions 16 A B 27. Plug the Cam Lock Covers (16) onto the visible Cams Locks to conceal the Cams.
Assembly Instructions N A B A B NOTE: To prevent your TV from tipping, you must follow these instructions if you place a TV on top of your console. Otherwise, skip to “Step 29”. 28. Remove the paper backing from the Stop Rail (N), then properly align the Stop Rail with the top edge of the stopper template on Top Panel (A). Press down on the Stop Rail to help adhesion. 29. Carefully remove the stopper template from the Top Panel (A).
Assembly Instructions A Tools required: Phillips screwdriver, stud finder, power drill and 1/8” drill bit. 30. Ask for assistance to position the assembled unit at the desired location against a wall. If necessary, adjust the installed Floor Levelers at the bottom of the Base to level the unit. Now, follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to attach the tip-over restraints to the unit and the wall.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO de LOTE: FECHA de COMPRA: / / Consola para media Canton Modelo # BHS0025004002 ENSAMBLE REQUERIDO POR ADULTOS Si tiene alguna pregunta relacionada con el montaje o si faltan piezas, NO devuelva este producto al establecimiento donde lo adquirió.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Consola para media Canton MODELO # BHS0025004002 PARA MAYORÍA DE LAS TELEVISIONES DE PANTALLA PLANA DE 177.8 cm / 70 pulgadas CARGA MÁXIMA 61.2 kg / 135 lb PONER LA TV DETRÁS DEL TOPE CARGA MÁXIMA 22.7 kg / 50 lb ESTA UNIDAD NO DEBE UTILIZARSE CON TELEVISIONES CRT O DE TUBO. UTILIZARSE ÚNICAMENTE CON TELEVISIONES DE PANTALLA PLANA Y EQUIPO DE AUDIO/VIDEO QUE TENGA LA MEDIDA/PESO RECOMENDADO.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 y 5 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma, SI ES NECESARIO.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y herramientas indicadas se encuentran presentes antes del comienzo del montaje. A- Panel superior (Cant. 1) B- Panel izquierdo (Cant. 1) D- Panel divisor izquierdo (Cant. 1) G- Panel inferior (Cant. 1) J- Puerta (Cant. 2) C- Panel derecho (Cant. 1) E- Panel divisor derecho (Cant. 1) H- Soporte inferior frontal (Cant. 1) K- Repisa ajustable pequeña (Cant.
Lista de partes y material de ferretería Le rogamos que lea completamente las instrucciones y verifique que todas las piezas y herramientas indicadas se encuentran presentes antes del comienzo del montaje. (1) Tuerca de fijación (Cant. 27+1 extra) (4) Perno de M4 x 50 mm (Cant. 4+1 extra) (7) Nivelador de piso (Cant. 2) (10) Soporte de repisa (Cant. 24+1 extra) (13) Perno de jaladera (Cant. 2) (2) Perno de fijación (Cant. 27+1 extra) (3) Clavija de madera de M8 x 30 mm (Cant.
Instructivo de ensamble C B F F G 2 ② x 19 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Atornillar los pernos de fijación (2) en los agujeros chicos designados en los paneles laterales (B y C), en el panel inferior (G) y en los soportes medios (F) usando el desarmador estrella.
Instructivo de ensamble D 3 3 E 3 3 ③x4 3. Pegar las clavijas de madera de 30 mm (3) en los agujeros internos de los paneles divisores (D y E).
Instructivo de ensamble F D 1 ① x3 4. Alinear y adjuntar un soporte medio (F) al panel divisor izquierdo (D) empleando 3 tuercas de fijación (1) (Consulte la página 3 del sistema de tuerca de fijación).
Instructivo de ensamble F E 1 ② x3 5. Repetir el mismo procedimiento para combinar el otro soporte medio (F) al panel divisor derecho (E).
Instructivo de ensamble 3 3 G 3 3 E 3 3 3 3 3 3 3 D 3 3 3 I 3 3 H 3 3 ③ x 18 6. Pegar las clavijas de madera de 30 mm (3) en los agujeros interiores del panel inferior (G), de los paneles divisores (D y E) y los soportes inferiores (H y I).
Instructivo de ensamble 1 G I G ①x3 7. Alinear y adjuntar el soporte inferior posterior (I) al panel inferior (G) empleando 3 tuercas de fijación (1).
Instructivo de ensamble 1 G H G I ①x4 8. Alinear y adjuntar el soporte inferior frontal (H) al panel inferior (G) empleando 4 tuercas de fijación (1).
Instructivo de ensamble E D H 4 G 4 4 I 4 ④x4 9. Adjuntar los paneles divisores (D y E) al panel inferior (G) con 4 pernos para madera de 50 mm (4).
Instructivo de ensamble B 3 3 C 3 3 ③x4 10. Pegar las clavijas de madera de 30 mm (3) en los agujeros laterales de los paneles laterales (B y C).
Instructivo de ensamble C E B/C D G G 1 B ①x6 11. Alinear los agujeros grandes en el panel izquierdo (B) con las clavijas de madera insertadas (3) en la base ensamblada. Presionar para juntar y sujetar en su lugar empleando 3 tuercas de fijación (1). 12. Repetir el paso previo para adjuntar el panel derecho (C) al otro lado.
Instructivo de ensamble 2 A ②x8 13. Atornillar los pernos de fijación (2) en los agujeros chicos designados en el panel superior (A) usando el desarmador estrella.
Instructivo de ensamble A 11 11 9 A x4 ⑨x2 14. Usando los agujeros pilotos como guía, sujetar 2 topes de puertas (9) al panel superior (A) con 4 pernos de cabeza plana de 15 mm (11).
Instructivo de ensamble 1 A C E D G B ①x8 15. Pedir asistencia para posicionar el panel superior (A) en las clavijas de madera insertadas (3). Adjuntar el panel superior (A) en su lugar empleando 8 tuercas de fijación (1).
Instructivo de ensamble C A E D G B 6 5 ⑤x8 ⑥x2 16. Con los agujeros pilotos como guía, alinear y adjuntar 2 placas de metal triangulares (6) a las esquinas frontales de la base ensamblada, usando 4 pernos de cabeza de arandela de 15 mm (5) por placas.
Instructivo de ensamble C A E D G B 7 ⑦x2 17. Atornillar 2 niveladores de piso (7) en los espacios roscados en las placas de metal triangulares (6) y ajustar a la altura correcta.
Instructivo de ensamble 8 8 M G C ⑧ x 24 18. Ahora, volver y apretar todas las tuercas de fijación y los pernos, asegurar que todas las partes estén apretadas y de que no hay huecos entre las partes, esto ayudara a mantener la unidad cuadrada. 19. Voltear la unidad ensamblada en sus bordes frontales. Desdoblar el panel posterior (M) y posicionar en los bordes posteriores del ensamble. Asegurar que la parte donde estan superpuestos los paneles esten nivelados todo el camino.
Instructivo de ensamble 15 15 15 15 14 14 J x2 x4 x8 20. Extender los brazos de bisagras (14) y descansar las tapas de bisagra en los recortes de los paneles de las puertas (J). Asegurar los brazos de bisagras en su lugar usando 2 pernos de zinc de 15 mm (15) en cada uno.
Instructivo de ensamble A C B J 14 J B/C 15 x 16 21. Poner la unidad en posición vertical. 22. Usando los agujeros pilotos como guía, tomar una puerta (J) y sujetar las bases de bisagras en el panel izquierdo (B) con 4 pernos de zinc de 15 mm (15) en cada uno. NO apretar completamente los pernos. 23. Repetir el mismo procedimiento para adjuntar la otra puerta (J) al panel derecho (C). 24. Abrir y cerrar las puertas para asegurar de que estén alineadas y se cierren correctamente.
Instructivo de ensamble A C 12 13 B 13 J 12 J x2 x2 25. Adjuntar una jaladera (12) al lado frontal de cada puerta (J) con los pernos de jaladera provistos (13).
Instructivo de ensamble A C L/K 10 11 B L K K L K K x 24 ⑩ x 24 26. Insertar 4 soportes de repisa (10) en los agujeros a la altura deseada en cada compartimiento lateral. Asegurar de poner los 4 soportes de repisa (10) en el mismo nivel para que la repisa no esté inclinada. Inclinar y descansar las repisas ajustables (K y L) en los soportes de repisa (10). Asegurar la repisa en su lugar con el perno de cabeza plana de 15 mm (11) Para soporte extra.
Instructivo de ensamble 16 A B 27. Enchufar la tapa de las tuercas de fijación (16) sobre las tuercas de fijación visibles para esconder.
Instructivo de ensamble N A B A B NOTA: Para evitar que su televisor su vuelque, se debe seguir estas instrucciones cuando se ubique su televisor en el mueble. Delo contrario, vaya al paso 29. 28. Retirar el respaldo de papel del riel tope (N), luego alinear el riel tope con el borde superior del templete del tope en el panel superior (A). Presionar el riel tope para ayudar a la adhesión. 29. Retirar el templete del tope del panel superior (A).
Instructivo de ensamble A Herramientas requeridas: Desarmador estrella, buscador de barrotes, taladro, lápiz, cinta métrica, y broca de 1/8”. 30. Pida assistencia para posicionar la chimenea ensamblada en el lugar deseado contra la pared. Si fuera necessario, ajuste los niveladores de piso pre-adjuntados en la parte inferior de la base para nivelar la unidad.
Mantenimiento y Cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera, pruebela en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los ponga sobre la unidad.