LOT NUMBER: DATE PURCHASED: / / Granary Modern Farmhouse TV Console Stock # BHW-10032 Rustic gray BHW-10033 White ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Granary Modern Farmhouse TV Console MODEL # BHW-10032 / BHW-10033 MADE IN VIETNAM FITS UP TO MOST 139.7 cm / 55” DIAGONAL FLAT PANEL TVS MAXIMUM LOAD 61.2 kg / 135 lb PLACE TV BEHIND THE STOPPER MAXIMUM LOAD 22.7 kg / 50 lb THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manuals. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH. Insert the dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) D- Left Fixed Shelf (Qty. 1) G- Partition Panel (Qty. 1) J- Bottom Front Stretcher (Qty. 1) M- Left Door (Qty. 1) P- Lower Back Panel (Qty. 1) B- Left Side Frame (Qty. 1) C- Right Side Frame (Qty. 1) E- Right Fixed Shelf (Qty. 1) F- Bottom Panel (Qty. 1) H- Partition Molding (Qty. 1) I- Top Front Stretcher (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Cam Lock (Qty. 27+1 extra) (4) M4 x 50 mm Screw (Qty. 2+1 extra) (7) Door Stopper (Qty. 2) (10) Handle (Qty. 8) Glue (Qty. 1) (2) Cam Bolt (Qty. 27+1 extra) (5) M3 x 15 mm Screw (Qty. 4+1 extra) (8) Shelf Pin (Qty. 8+1 extra) (11) 5/32 x 16 mm Bolt (Qty. 16+1 extra) Touch-up Pen (Qty.
Assembly Instructions 2 A C H B J ② x 23 1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), Left Side Frame (B), Right Side Frame (C), Partition Molding (H) and Bottom Front Molding (J) using a Phillips screwdriver.
Assembly Instructions 2 G G ②x4 3. Securely screw two Cam Bolts (2) into the designated small holes on one face of Partition Panel (G). 4. Repeat the same procedure to screw another two Cam Bolts (2) on the other face of Partition Panel (G).
Assembly Instructions E D 5 7 ⑤x4 ⑦x2 5. With the pilot holes as a guide, fasten one Door Stopper (7) to the Left Fixed Shelf (D) using two 15 mm Flat Head Screws (5). 6. Repeat the same procedure to attach the other Door Stopper (7) to the Right Fixed Shelf (E).
Assembly Instructions G 3 3 ③x2 7. Glue two Wood Dowels (3) into the inner holes of the Partition Panel (G). NOTE: It is very important to use a small amount of glue on both ends of dowels.
Assembly Instructions 1 H 1 G 1 ① x3 8. Align and attach the Partition Molding (H) to the Partition Panel (G) by engaging three Cam Locks (1).
Assembly Instructions 3 3 F 3 3 3 3 3 3 G 3 3 3 J 3 ③ x 12 9. Glue the Wood Dowels (3) into the inner holes of the Bottom Panel (F), Partition Panel (G) and Bottom Front Stretcher (J) as shown. NOTE: DO NOT insert the wood dowels into the cam bolts holes.
Assembly Instructions G F 4 4 ④x2 10. Using the wood dowels as a guide, firmly press the Partition Panel (G) to the Bottom Panel (F) and fasten them in place with two 50 mm Screws (4). Fully tighten the screws with a Phillips screwdriver.
Assembly Instructions J 1 G 1 1 1 F ① x4 11. Attach the Bottom Front Stretcher (J) to the Bottom Panel (F) with four Cam Locks (1).
Assembly Instructions B C 3 3 3 3 3 3 3 3 D E 3 3 3 3 ③ x 12 12. Glue the Wood Dowels (3) into the inner holes of the Left Side Frame (B), Right Side Frame(C), Left Fixed Shelf (D) and Right Fixed Shelf (E) as shown.
Assembly Instructions 1 1 E 1 G F D 1 ① x4 13. Attach the Fixed Shelves (D and E) to the Partition Panel (G) by engaging two Cam Locks (1) repectively.
Assembly Instructions C E D B/C F F 1 B ① x 10 14. Align and attach the Side Frames (B and C) to previous assembly with ten Cam Locks (1).
Assembly Instructions 3 I 3 ③x2 15. Glue two Wood Dowels (3) into the inner holes of the Top Front Stretcher (I) as shown.
Assembly Instructions 12 12 12 I 12 A ⑫x4 16. Fasten the Top Front Strethcer (I) to the Top Panel (A) with four 38 mm Screws (12).
Assembly Instructions A 1 A C G B F ① x6 17. Place the Top Panel (A) onto the inserted Wood Dowels (3) on the vertical panels properly and fasten it in place with six Cam Locks (1).
Assembly Instructions B F Q 18. Securely screw the Support Foot (Q) into the threaded insert on the Bottom Panel (F) and set the floor leveler to the correct height.
Assembly Instructions 6 6 O/P O P F C ⑥ x 28 19. Now, go back and securely tighten all the cam locks and screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 20. Ask for assistance to flip the unit around at its front edge as shown. 21. Pick up the Upper Back Panel (O) and align the pre-drilled holes against the long edge with the pilot holes on the back of Top Panel (A).
Assembly Instructions A B Up N 1 Up M 10 11 11 x 16 ⑩ x8 23. Ask for assistance to lift the assembly unit upright and position it near the final location. 24. Pick up the Left Door (M) and attach the extended Hinge Arms to the Hinge Bases installed on the Left Side Frame (B). Loosen the bolt on the back of Hinge Base for an easy fit. Align and insert the “U” slot on Hinge Arm under the bolt head on the back of Hinge Base. Make sure that both door hinges engage and function properly.
Assembly Instructions 9 A C 8 B L 8 K ⑧ x8 ⑨ x 17 28. Insert four Shelf Pins (8) into the holes at the desired height inside each lower compartment. Tilt and rest the Adjustable Shelves (K and L) onto the Shelf Pins (8). 29. Plug the Cam Lock Covers (9) onto the visible cam locks to conceal the cams.
Assembly Instructions R A B A A B NOTE: To prevent your TV from tipping, you must install the Strip Stopper if you place your flat panel television directly on the console. Otherwise, skip to step 32. 30. Remove the paper backing of Stop Rail (R), then properly align the Stop Rail with the top edge of the stopper template on Top Panel (A). Press down on the Stop Rail to help adhesion. 31. Carefully remove the Stopper template from Top Panel (A).
Assembly Instructions Tools required (not included): Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit. 32. Ask for assistance to position the assembled unit at the desired location against a wall. If necessary, adjust the pre-attached Floor Levelers at the bottom of Side Frames (B and C) and Support Foot (Q) to level the unit. 33.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
NÚMERO de LOTE: FECHA de COMPRA: / / Consola para TV Granary Modern Farmhouse Modelo # BHW-10032 Gris rústico # BHW-10033 Blanco ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 866-942-5362 Hora Estándar del Pacífico: 8:30 a.m.
MÁXIMO PESO RECOMENDADO FABRICANTE: Whalen Furniture Manufacturing CATALOGO: Consola para TV Granary Modern Farmhouse MODELO # BHW-10032 / BHW-10033 HECHO EN VIETNAM PARA LA MAYORÍA DE TV’S DE 139.7 cm / 55 pulgadas PANTALLA PLANA CARGA MÁXIMA 61.2 kg / 135 lb PONER LA TV DETRÁS DEL TOPE CARGA MÁXIMA 22.7 kg / 50 lb ESTA UNIDAD NO DEBE UTILIZARSE CON TELEVISIONES CRT O DE TUBO. UTILIZARSE ÚNICAMENTE CON TELEVISIONES DE PANTALLA PLANA Y EQUIPO DE AUDIO/VIDEO QUE TENGA LA MEDIDA/PESO RECOMENDADO.
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 y 5 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE PARA EL USO DE PEGAMENTO CON LAS CLAVIJAS DE MADERA. EL. EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO. Inserte la clavija por lo menos a la mitad del camino golpeando ligeramente con un mazo de pegamento, SI ES NECESARIO.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. A- Panel superior (Cant. 1) B- Marco izquierdo (Cant. 1) C- Marco derecho (Cant. 1) D- Repisa fija izquierda (Cant. 1) E- Repisa fija derecha (Cant. 1) F- Panel inferior (Cant. 1) G- Panel divisor (Cant. 1) J- Soporte inferior frontal (Cant. 1) M- Puerta izquierda (Cant. 1) P- Panel inferior posterior (Cant.
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. (1) Tuerca de fijación (Cant. 27+1 extra) (4) Perno de M4 x 50 mm (Cant. 2+1 extra) (7) Tope de puerta (Cant. 2) (10) Manija (Cant. 8) Pegamento (Cant. 1) (2) Perno de fijación (Cant. 27+1 extra) (5) Perno de M3 x 15 mm (Cant. 4+1 extra) (3) Clavija de madera M8 x 30 mm (Cant.
Instrucciones de ensamble 2 A C H B J ② x 23 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Atornillar los pernos de fijación (2) en los agujeros pequeños designados en el panel superior (A), el marco izquierdo (B), el marco derecho (C), la moldura divisora (H) y el soporte inferior frontal (J) usando el desarmador estrella.
Instrucciones de ensamble 2 G G ②x4 3. Atornillar 2 pernos de fijación (2) en los agujeros pequeños designados en una cara del panel divisor (G). 4. Repetir el mismo procedimiento para atornillar otros 2 pernos de fijación (2) en la otra cara del panel divisor (G).
Instrucciones de ensamble E D 5 7 ⑤x4 ⑦x2 5. Con los agujeros pilotos como guía, sujetar un tope de puerta (7) a la repisa fija izquierda (D) usando 2 pernos cabeza plana de 15 mm (5). 6.
Instrucciones de ensamble G 3 3 ③x2 7. Pegar con pegamento 2 clavijas de madera (3) en los agujeros internos del panel divisor (G). Nota: Usar una cantidad pequeña de pegamento en ambos lados de las clavijas.
Instrucciones de ensamble 1 H 1 G 1 ① x3 8. Alinear y adjuntar la moldura divisora (H) al panel divisor (G) empleando 3 tuercas de fijación (1). (Consulte la página 3 del sistema de tuerca de fijación).
Instrucciones de ensamble 3 3 F 3 3 3 3 3 3 G 3 3 3 J 3 ③ x 12 9. Pegar con pegamento las clavijas de madera (3) en los agujeros internos del panel inferior (F), del panel divisor (G) y en el soporte inferior frontal (J) como se muestra. NOTA: NO insertar las clavijas de madera en los agujeros de los pernos de fijación.
Instrucciones de ensamble G F 4 4 ④x2 10. Usando las clavijas de madera como guía, presionar el panel divisor (G) al panel inferior (F) y sujetar en su lugar con 2 pernos de 50 mm (4). Apretar los pernos con el desarmador estrella.
Instrucciones de ensamble J 1 G 1 1 1 F ① x4 11. Adjuntar el soporte inferior frontal (J) al panel inferior (F) con 4 tuercas de fijación (1).
Instrucciones de ensamble B C 3 3 3 3 3 3 3 3 D E 3 3 3 3 ③ x 12 12. Pegar con pegamento las clavijas de madera (3) en los agujeros internos del marco izquierdo (B), del marco derecho (C), de la repisa fija izquierda (D) y de la repisa fija derecha (E) como se muestra.
Instrucciones de ensamble 1 1 E 1 G F D 1 ① x4 13. Adjuntar las repisas fijas (D y E) al panel divisor (G) empleando 2 tuercas de fijación (1).
Instrucciones de ensamble C E D B/C F F 1 B ① x 10 14. Alinear y adjuntar los marcos laterales (B y C) al ensamble previo con 10 tuercas de fijación (1).
Instrucciones de ensamble 3 I 3 ③x2 15. Pegar 2 clavijas de madera (3) en los agujeros internos del soporte superior frontal (I) como se muestra.
Instrucciones de ensamble 12 12 12 I 12 A ⑫x4 16. Sujetar el soporte superior frontal (I) al panel superior (A) con 4 pernos de 38 mm (12).
Instrucciones de ensamble A 1 A C G F B ① x6 17. Poner el panel superior (A) en las clavijas de madera insertadas (3) en los paneles verticales y sujetar en su lugar con 6 tuercas de fijación (1).
Instrucciones de ensamble B F Q 18. Atornillar la pata de soporte (Q) en los insertos roscados en el panel inferior (F) y ajustar el nivelador de piso a la altura correcta.
Instrucciones de ensamble 6 6 O/P O P F C ⑥ x 28 19. Ahora, volver y apretar todas las tuercas y los pernos de fijación. Asegurar que todas las partes estén apretadas y que no hay espacios entre las partes. Esto ayudara a mantener la unidad cuadrada. 20. Pedir asistencia para voltear la unidad en sus bordes frontales como se muestra. 21.
Instrucciones de ensamble A B Up N 1 Up M 10 11 11 ⑩ x8 x 16 23. Pedir asistencia para levantar la unidad de ensamble en posición vertical y cerca del lugar final. 24. Tomar la puerta izquierda (M) y adjuntar el brazo de bisagra extendido a las bases de bisagras instaladas en el marco izquierdo (B). Aflojar el perno detrás de la base para un ajuste fácil. Alinear e insertar el espacio “U” en el brazo abajo de la cabeza del perno detrás de la base.
Instrucciones de ensamble 9 A C 8 B L 8 K ⑧ x8 ⑨ x 17 28. Insertar 4 pernos de repisa (8) en los agujeros a la altura deseada adentro de cada compartimiento inferior. Inclinar y descansar las repisas ajustables (K y L) sobre los pernos de repisa (8). 29. Enchufar las tapas de las tuercas de fijación (9) sobre las tuercas de fijación visibles para esconder.
Instrucciones de ensamble R A B A A B NOTA: Para prevenir que la TV se incline, debe instalar el tope acrílico de TV si pone su televisión de pantalla plana directamente sobre la consola. Por el contrario, saltar al paso 32. 30. Retirar el respaldo de papel del riel tope (R), luego alinear el riel tope con el borde superior del templado del tope en el panel superior (A). Presionar para abajo el riel tope para ayudar a la adhesión. 31. Retirar el templado del tope del panel superior (A).
Instrucciones de ensamble Herramientas requeridas (no incluidas): Desarmador estrella, localizador de barrotes, cinta métrica, lápiz, taladro y broca de 1/8”. 32. Pida asistencia para posicionar la consola ensamblada en el lugar deseado contra la pared. Si fuera necesario, ajustar los niveladores de piso pre-adjuntados en la parte inferior de los marcos laterales (B y C) y en la pata soporte (Q) para nivelar la unidad. 33.
Mantenimiento y cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera cheque en un área que no sea visible para revisar su funcionamiento. Usar solventes de cualquier tipo puede dañar el acabado del mueble. Nunca use agua para limpiar la unidad, ya que le puede dañar el acabado. Siempre utilice protección para vasos cuando los ponga sobre la unidad.