TWIN BUNKBED Model Number: WM7891-1 WM7891 WM7891W-1 WM7891W UPC Code: 0-65857-18612-3 0-65857-18612-3 0-65857-18662-8 0-65857-18665-9 Color: Mocha Mocha White White Customer satisfaction is important to us at Dorel Asia. Our agents are available Monday to Friday 8am to 5pm (EST) to answer any question you may have. For faster service, always have the model number ready when calling our toll free number 1-800-295-1980 or emailing us at das@dorel.com .
CUSTOMER SERVICE If you are missing parts or have any questions about this product, contact our customer service representative first! CALL 1-800-295-1980 You can also order parts by writing to the address listed below. Please include the product model number, color and a detailed description of the part. Customer Service Department No.
* KEEP THESE INSTRUCTIONS FOR FUTURE USE. NOTES * READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH STEP OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN RESULT IN INJURY. * CAUTION: ADULT ASSEMBLY REQUIRED * MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A SMOOTH SOFT SURFACE. * ASSEMBLY WILL REQUIRE TWO PEOPLE. * MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
TWIN BUNK BED HARDWARE LIST 1 2 Φ 1/4" x 100mm Φ 6.5mm x 48mm JOINT CONNECTOR (4mm HEX HEAD) 16 PCS WOOD JOINT CONNECTOR (4mm HEX HEAD) 10 PCS 3 4 Φ 6.5mm x 100mm Φ 4mm x 35mm WOOD JOINT CONNECTOR (4mm HEX HEAD) 24 PCS FLAT HEAD SCREW 24 PCS 5 6 Φ 10mm x 100mm Φ 4mm x 30mm METAL DOWEL 4 PCS FLAT HEAD SCREW 6 PCS 7 8 Φ 10mm x 50mm WOOD DOWEL 62 PCS 9 ALLEN KEY 1 PC 10 11 Φ 11.
TWIN BUNK BED PARTS LIST A B C TOP POST 1 PC TOP POST 2 PCS D TOP POST 1 PC E F BOTTOM POST 2 PCS BOTTOM POST 2 PCS HEADBOARD TOP CROSS 4 PCS G F L L B A L U F J E Q L N Q H S L D Q S F N G L G C L O K T P B T I S F L L G E D
TWIN BUNK BED PARTS LIST G H HEADBOARD BOTTOM CROSS 4 PCS J I TOP FRONT SIDE RAIL 1 PC K BACK SIDE RAIL 1 PC M L BOTTOM BACK SIDE RAIL 1 PC N LONG GUARDRAIL 2 PCS P SHORT GUARDRAIL 2 PCS RIGHT LADDER END 1 PC HEADBOARD CENTER CROSS 4 PCS SLAT WITHOUT WOOD DOWEL 12 PCS O Q S BOTTOM FRONT SIDE RAIL 1 PC LEFT LADDER END 1 PC R LADDER STEP 3 PCS T GUARDRAIL LEG 2 PCS U SLAT WITH WOOD DOWEL 4 PCS GUARDRAIL POST 1 PC
TWIN BUNK BED 7 7 7 7 7 7 7 7 7 7 7 7 7 7 A 7 7 C 3 STEP 1 Insert wood dowels (7) into the ends of headboard top cross (F), headboard bottom cross (G) and headboard center cross (S). Attach them to top posts (A & B) using wood joint connectors (3) as shown. Tighten the wood joint connectors (3) with the Allen key (8). NOTES: Headboard top crosses (F, G& S) may require that they be pulled closer together or further apart in order to allow wood dowels (7) to align with holes in top posts (A & B).
TWIN BUNK BED 7 E 7 7 7 7 E 7 7 7 D 7 7 7 7 7 7 D 7 7 STEP 2 3 Insert wood dowels (7) into the ends of headboard top cross (F), headboard bottom cross (G) and headboard center cross (S) and attach them to bottom posts (D) & (E) using wood joint connectors (3) as shown. Tighten the wood joint connectors (3) with the Allen key (8).
TWIN BUNK BED K I STEP 3 Attach the two headboards with bottom posts (D & E) to bottom front side rail (I) and bottom back side rail (K) using joint connectors (1) and barrel nuts (9) as shown. Tighten the joint connectors (1) with the Allen key (8). Note: This is the lower bunk.
TWIN BUNK BED J H STEP 4 Insert wood dowels (7) into each end of the long guardrails (M). Attach two long guardrails (M) and two top side rails (H & J) to top posts (A & B) and (C & B) as shown. Fasten top side rails (H & J) with joint connectors (1) and barrel nuts (9). Fasten long guardrails (M) with wood joint connectors (3). Tighten the joint connectors (1) and wood joint connectors (3) with the Allen key (8).
TWIN BUNK BED U 8 3 U 7 7 11 10 A N H B 10 STEP 5 Insert wood dowels (7) into short guardrails (N). Attach short guardrails (N) to guardrail post (U) with wood joint connectors (3) as shown. Fasten the short guardrails (N) to top post (B) with wood joint connectors (3). Fasten the guardrail post (U) to top front side rail (H) with joint connectors (10) and hex cap (11) as shown.
TWIN BUNK BED M 6 N 6 6 H 6 STEP 6 Attach the guardrail leg (R) to the short guardrails (N) and top front side rail (H) with flat head screws (6). Attach the other guardrail leg (R) (on the other side of the bed) to long guardrails (M) and top back side rail (J) with flat head screws (6) as shown. Use a Phillips head screwdriver (not included) to tighten the flat head screws.
TWIN BUNK BED O P STEP 7 Insert wood dowels (7) into the end of the ladder steps (Q). Attach left ladder end (O) and right ladder end (P) to ladder steps (Q) with wood joint connectors (2). Tighten the wood joint connectors (2) with the Allen key (8).
TWIN BUNK BED B 5 A H 5 C D 5 B I D 5 E STEP 8 insert the metal dowels (5) into the holes in the bottom posts (D and E). Stack the top bunk onto the bottom bunk with the help of another person.
TWIN BUNK BED A U 2 N H D 2 O P I A N U 2 H 2 D O P I 2 2 8 back view STEP 9 Attach the ladder to the top front side rail (H) and bottom front side rail (I) with wood joint connectors (2) as shown. Use Allen key (8) to tighten the joint connectors.
TWIN BUNK BED J 4 H L K I 4 STEP 10 Insert two slats with wood dowel (T) into the center slots of the top side rails (H &J) of the upper bunk as shown. Attach slats without wood dowel (L) onto top side rails (H &J) of the upper bunk with flat head screws (4) as shown. Use Phillips screwdriver (not included) to tighten flat head screws (4). Repeat this process for the bottom bunk.
TWIN BUNK BED To convert your bunk bed into two separate beds, remove the ladder and all the guardrails. With the help of another person, unstack the top bunk from the lower bunk.
TWIN BUNK BED CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED. DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK. BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG TEENAGERS.
CAMAS CUCHETAS SIMPLES Modelo No: WM7891-1 WM7891 WM7891W-1 WM7891W CODIGO UPC: 0-65857-18612-3 0-65857-18612-3 0-65857-18662-8 0-65857-18665-9 Color: MOCA MOCA BLANCO BLANCO ¡Le damos mucha importancia a la satisfacción de nuestros clientes. Nuestros representantes están disponibles de lunes a viernes de 8 h a 17 h (hora del este) para responder a todas sus preguntas.
SERVICIO AL CLIENTE Si faltan piezas o si tiene alguna pregunta sobre este producto, ¡comuníquese con nuestro representante de servicio! LLAME AL 1-800-295-1980 También puede pedir piezas escribiendo a la siguiente dirección. Por favor incluya el número de modelo, color y una descripción detallada de la pieza. Departamento de Servicio al Cliente No.
* CONSERVE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. NOTAS * LEA ATENTAMENTE CADA ETAPA ANTES DE COMENZAR. ES MUY IMPORTANTE QUE CADA ETAPA SE LLEVE A CABO EN EL ORDEN CORRECTO. SI ESTAS ETAPAS NO SE SIGUEN EN ORDEN, PUEDEN SURGIR DIFICULTADES PARA ARMAR LA CAMA Y CAUSAR LESIONES A LOS NIÑOS QUE LA USAN. * DEBE SER ARMADA POR UN ADULTO. * ASEGÚRESE DE TENER TODAS LAS PIEZAS. TRABAJE EN UN LUGAR ESPACIOSO, DE PREFERENCIA SOBRE UN TAPIZ. * SE NECESITARÁN DOS PERSONAS PARA ARMARLA.
CAMAS CUCHETAS SIMPLES LISTA DE ACCESORIOS 1 2 Φ 1/4" x 100mm Φ 6.5mm x 48mm PERNO CONECTOR (4MM CABEZA HEXAGONAL) PERNO CONECTOR MADERA (4MM CABEZA 16 PCS HEXAGONAL) 10 PCS 3 4 Φ 6.5mm x 100mm Φ 4mm x 35mm PERNO CONECTOR MADERA (4MM CABEZA HEXAGONAL) 24 PCS TORNILLO CABEZA PLANA 24 PCS 5 6 Φ 10mm x 100mm Φ 4mm x 30mm CLAVIJA DE METAL 4 PCS TORNILLO CABEZA PLANA 6 PCS 7 8 Φ 10mm x 50mm CLAVIJA DE MADERA 62 PCS 9 LLAVE ALLEN 1 PC 10 11 Φ 11.
CAMAS CUCHETAS SIMPLES LISTA DE PIEZAS A B C PATA SUPERIOR 1 PC PATA SUPERIOR 2 PCS D PATA SUPERIOR 1 PC E F PATA INFERIOR 2 PCS PATA INFERIOR 2 PCS TRAVESAÑO SUPERIOR CABECERA 4 PCS G F L L B A L U F J E Q L N Q H S L D Q S F N G L G C L O K T P B T I S F L L G E D
CAMAS CUCHETAS SIMPLES LISTA DE PIEZAS G H I TRAVESAÑO INFERIOR CABECERA LARGUERO LATERAL SUPERIOR LARGUERO LATERAL INFERIOR 4 PCS ANTERIOR 1 PC ANTERIOR 1 PC J K L LARGUERO LATERAL POSTERIOR LARGUERO LATERAL INFERIOR LISTÓN SIN CLAVIJA DE MADERA 1 PC POSTERIOR 1 PC 12 PCS M N BARANDA LARGA 2 PCS P O BARANDA CORTA 2 PCS Q LADO DERECHO ESCALERA 1 PC S R ESCALÓN 3 PCS T SOPORTE DE BARANDA 2 PCS U TRAVESAÑO CENTRAL CABECERA LISTÓN CON CLAVIJA DE MADERA 4 PCS LADO IZQUIERDO ESC
CAMAS CUCHETAS SIMPLES 7 7 Etiqueta de advertencia 7 7 7 7 7 7 7 7 7 7 7 7 A 7 7 C 3 ETAPA 1 Inserte clavijas de madera (7) en los extremos del travesaño superior de la cabecera (F), del travesaño inferior de la cabecera (G) y del travesaño central de la cabecera (S). Únalos con las patas superiores (A y B) con pernos conectores para madera (3) como ilustrado. Ajuste los pernos conectores para madera (3) con la llave Allen (8).
CAMAS CUCHETAS SIMPLES 7 E 7 7 7 7 E 7 7 7 D 7 7 7 7 7 7 D 7 7 ETAPA 2 3 Inserte clavijas de madera (7) en los extremos del travesaño superior de cabecera (F), del travesaño inferior de cabecera (G) y del travesaño central de cabecera (S) y únalos con las patas inferiores (D) y (E) con pernos conectores para madera (3) como ilustrado. Ajuste los pernos conectores para madera (3) con la llave Allen (8).
CAMAS CUCHETAS SIMPLES K I ETAPA 3 Una las dos cabeceras con las patas inferiores (D y E) al larguero lateral inferior anterior (I) y al larguero lateral inferior posterior (K) con pernos conectores (1) y tuercas barrilete (9) como ilustrado. Ajuste los pernos conectores (1) con la llave Allen (8). Nota: Ésta es la cama inferior.
CAMAS CUCHETAS SIMPLES J H ETAPA 4 Inserte clavijas de madera (7) en los extremos de las barandas largas (M). Una las dos barandas largas (M) y los dos largueros laterales superiores (H y J) con las patas superiores (A y B) y (C y B) como ilustrado. Fije los largueros laterales superiores (H y J) con pernos conectores (1) y tuercas barrilete (9). Fije las barandas largas (M) con pernos conectores para madera (3).
CAMAS CUCHETAS SIMPLES U 8 3 U 7 7 11 10 A N H B 10 ETAPA 5 Inserte clavijas de madera (7) en las barandas cortas (N). Una las barandas cortas (N) al soporte de baranda (U) con pernos conectores para madera (3) como ilustrado. Fije las barandas cortas (N) a la pata superior (B) con pernos conectores para madera (3). Fije el soporte de baranda (U) al larguero lateral superior anterior (H) con pernos conectores (10) y pernos de brida hexagonal (11) como ilustrado.
CAMAS CUCHETAS SIMPLES M 6 N 6 6 H 6 ETAPA 6 Una un soporte de baranda (R) a las barandas cortas (N) y al larguero lateral superior anterior (H) con tornillos de cabeza plana (6). Una el otro soporte de baranda (R) (del otro lado de la cama) con las barandas largas (M) y el larguero lateral superior posterior (J) con tornillos de cabeza plana (6) como ilustrado. Utilice un destornillador Phillips (no incluido) para ajustar los tornillos de cabeza plana.
CAMAS CUCHETAS SIMPLES O P ETAPA 7 Inserte clavijas de madera (7) en los extremos de los escalones (Q). Una el lado izquierdo de la escalera (O) y el lado derecho de la escalera (P) a los escalones (Q) con pernos conectores para madera (2). Ajuste los pernos conectores para madera (2) con la llave Allen (8).
CAMAS CUCHETAS SIMPLES B 5 A Agujeros H 5 C D 5 B I D 5 Agujeros E Agujeros ETAPA 8 Inserte las clavijas de metal (5) en los agujeros de las patas inferiores (D y E). Con la ayuda de otra persona, coloque la cama superior sobre la cama inferior.
CAMAS CUCHETAS SIMPLES A U 2 N H D 2 O P I A N U 2 H 2 D O P I 2 2 8 back view Vista Posterior ETAPA 9 Una la escalera al larguero lateral superior anterior (H) y al larguero lateral inferior anterior (I) con pernos conectores para madera (2) como ilustrado. Utilice la llave Allen (8) para ajustar los pernos conectores.
CAMAS CUCHETAS SIMPLES Listones: 8 piezas para la cama superior 8 piezas para la cama inferior J H 4 L K I 4 ETAPA 10 Inserte dos listones con clavija de madera (T) en las ranuras ubicadas en el centro de los largueros laterales superiores (H y J) de la cama superior como ilustrado. Fije los listones sin clavija de madera (L) en los largueros laterales superiores (H y J) de la cama superior con tornillos de cabeza plana (4) como ilustrado.
CAMAS CUCHETAS SIMPLES La primera cama simple La segunda cama simple Para convertir las camas cuchetas en dos camas simples separadas, retire la escalera y todas las barandas. Con la ayuda de otra persona, retire la cama superior de la cama inferior.
CAMAS CUCHETAS SIMPLES PRECAUCIÓN: Esta unidad está diseñada para ser utilizada únicamente con los productos y/o pesos máximos indicados. Su uso con otros productos y/o productos más pesados que los pesos máximos indicados puede provocar inestabilidad o causar lesiones. NO PERMITA QUE LOS NIÑOS HAGAN PAYASADAS SOBRE O DEBAJO DE LA CAMA Y PROHIBA QUE SALTEN SOBRE ELLA. NO PERMITA QUE NIÑOS MENORES DE 6 AÑOS DUERMAN EN LA CUCHETA SUPERIOR.
LITS SIMPLES SUPERPOSÉS Modèle No: Code CUP: Couleur: WM7891-1 0-65857-18612-3 MOKA WM7891 0-65857-18612-3 MOKA WM7891W-1 0-65857-18662-8 BLANC WM7891W 0-65857-18665-9 BLANC La satisfaction de nos clients est important pour nous chez Dorel Asia. Nos représentants sont disponibles du lundi au vendredi de 8 h à 17 h (heure de l’est) pour répondre à toutes vos questions.
SERVICE À LA CLIENTÈLE Si des pièces sont manquantes ou si vous avez des questions concernant ce produit, contactez un représentant de notre service à la clientèle d'abord! APPELEZ 1-800-295-1980 Vous pouvez aussi commander des pièces en écrivant à l'adresse indiquée ci-dessous. Veuillez inclure le numéro de modèle du produit, la couleur et une description détaillée de la pièce. Service à la clientèle, Département No. 413 12345 boul.
* INTERDIRE PLUS D'UNE PERSONNE SUR LE LIT SUPÉRIEUR. * CONSERVEZ CES INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE. NOTES * LIRE ATTENTIVEMENT CHAQUE ÉTAPE AVANT DE COMMENCER. IL EST TRÈS IMPORTANT QUE CHAQUE ÉTAPE SOIT EXÉCUTÉE DANS L'ORDRE APPROPRIÉ. SI CES ÉTAPES NE SONT PAS SUIVIES DANS L'ORDRE, DES DIFFICULTÉS D'ASSEMBLAGE SE PRODUIRONT ET PEUVENT ENTRAÎNER DES BLESSURES. * ATTENTION: ASSEMBLAGE PAR UN ADULTE REQUIS. * ASSUREZ-VOUS QUE TOUTES LES PIÈCES SONT INCLUSES.
LITS SIMPLES SUPERPOSÉS LISTE DE QUINCAILLERIE 1 2 Φ 1/4" x 100mm Φ 6.5mm x 48mm BOULON DE RACCORDEMENT (4MM TÊTE HEXAGONALE) BOULON DE RACCORDEMENT BOIS (4MM TÊTE HEXAGONALE) 10 PCS 16 PCS 3 4 Φ 6.5mm x 100mm Φ 4mm x 35mm BOULON DE RACCORDEMENT BOIS (4MM TÊTE HEXAGONALE) 24 PCS VIS À TÊTE PLATE 24 PCS 5 6 Φ 10mm x 100mm Φ 4mm x 30mm GOUJON DE MÉTAL 4 PCS VIS À TÊTE PLATE 6 PCS 7 8 Φ 10mm x 50mm GOUJON DE BOIS 62 PCS 9 CLÉ ALLEN 1 PC 10 11 Φ 11.
LITS SIMPLES SUPERPOSÉS LISTE DE PIÈCES A B C PIED SUPÉRIEUR 1 PC PIED SUPÉRIEUR 2 PCS D PIED SUPÉRIEUR 1 PC E F PIED INFÉRIEUR 2 PCS PIED INFÉRIEUR 2 PCS TRAVERSE SUPÉRIEURE TÊTE DE LIT 4 PCS G F L L B A L U F J E Q L N Q S L D Q S F H N G L G C L O K T P B T I S F L L G E D
LITS SIMPLES SUPERPOSÉS LISTE DE PIÈCES G H I TRAVERSE INFÉRIEURE TÊTE DE LIT BARRE LATÉRALE SUPÉRIEURE AVANT BARRE LATÉRALE INFÉRIEURE AVANT 4 PCS 1 PC 1 PC J K BARRE LATÉRALE ARRIÈRE BARRE LATÉRALE INFÉRIEURE ARRIÈRE LATTE SANS GOUJON DE BOIS 1 PC 1 PC 12 PCS M N BARRIÈRE LONGUE 2 PCS P O BARRIÈRE COURTE 2 PCS Q CÔTÉ DROIT ÉCHELLE 1 PC S L CÔTÉ GAUCHE ÉCHELLE 1 PC R MARCHE 3 PCS T TRAVERSE CENTRALE TÊTE DE LIT LATTE AVEC GOUJON DE BOIS 4 PCS 4 PCS SUPPORT DE BARRIÈRE 2 PCS
LITS SIMPLES SUPERPOSÉS 7 7 7 Etiqueta de advertencia 7 7 7 7 7 7 7 7 7 7 7 A 7 7 C 3 ÉTAPE 1 Insérez des goujons de bois (7) dans les extrémités de la traverse supérieure de la tête de lit (F), dans la traverse inférieure de la tête de lit (G) et dans la traverse centrale de la tête de lit (S). Fixez-les aux pieds supérieurs (A et B) avec des boulons de raccordement pour bois (3) tel qu’illustré. Serrez les boulons de raccordement pour bois (3) à l’aide de la clé Allen (8).
LITS SIMPLES SUPERPOSÉS 7 E 7 7 7 7 E 7 7 7 D 7 7 7 7 7 7 D 7 7 ÉTAPE 2 3 Insérez des goujons de bois (7) dans les extrémités de la traverse supérieure de tête de lit (F), dans la traverse inférieure de tête de lit (G) et dans la traverse centrale de tête de lit (S) et fixez-les aux pieds inférieurs (D) et (E) avec des boulons de raccordement pour bois (3) tel qu’illustré. Serrez les boulons de raccordement pour bois (3) à l’aide de la clé Allen (8).
LITS SIMPLES SUPERPOSÉS K I ÉTAPE 3 Fixez les deux têtes de lit aux pieds inférieurs (D et E), à la barre latérale inférieure avant (I) et à la barre latérale inférieure arrière (K) avec des boulons de raccordement (1) et des écrous transversaux (9) tel qu’illustré. Serrez les boulons de raccordement (1) à l’aide de la clé Allen (8). Note : Ceci est le lit inférieur.
LITS SIMPLES SUPERPOSÉS J H ÉTAPE 4 Insérez des goujons de bois (7) dans les extrémités des barrières longues (M). Fixez les deux barrières longues (M) et les barres latérales supérieures (H et J) aux pieds supérieurs (A et B) et (C et B) tel qu’illustré. Fixez les barres latérales supérieures (H et J) avec des boulons de raccordement (1) et des écrous transversaux (9). Fixez les barrières longues (M) avec des boulons de raccordement pour bois (3).
LITS SIMPLES SUPERPOSÉS U 8 3 U 7 7 11 10 A N H B 10 ÉTAPE 5 Insérez des goujons de bois (7) dans les barrières courtes (N). Fixez les barrières courtes (N) au support de barrière (U) avec des boulons de raccordement pour bois (3) tel qu’illustré. Fixez les barrières courtes (N) au pied supérieur (B) avec des boulons de raccordement pour bois (3).
LITS SIMPLES SUPERPOSÉS M 6 N 6 6 H 6 ÉTAPE 6 Fixez un support de barrière (R) aux barrières courtes (N) et à la barre latérale supérieure avant (H) avec des vis à tête plate (6). Fixez l’autre support de barrière (R) (de l’autre côté du lit) aux barrières longues (M) et à la barre latérale supérieure arrière (J) avec des vis à tête plate (6) tel qu’illustré. Servez-vous d’un tournevis cruciforme (non compris) pour serrer les vis à tête plate.
LITS SIMPLES SUPERPOSÉS O P ÉTAPE 7 Insérez des goujons de bois (7) dans les extrémités des marches (Q). Fixez le côté gauche de l’échelle (O) et le côté droit de l’échelle (P) aux marches (Q) avec des boulons de raccordement pour bois (2). Serrez les boulons de raccordement pour bois (2) à l’aide de la clé Allen (8).
LITS SIMPLES SUPERPOSÉS B 5 A Trous H 5 C D 5 B I D 5 Trous E Trous ÉTAPE 8 Insérez des goujons de métal (5) dans les trous des pieds inférieurs (D et E). Avec l’aide d’une autre personne, placez le lit supérieur sur le lit inférieur.
LITS SIMPLES SUPERPOSÉS A U 2 N H D 2 O P I A N U 2 H 2 D O P I 2 2 8 back view Vue arrière ÉTAPE 9 Fixez l’échelle à la barre latérale supérieure avant (H) et à la barre latérale inférieure avant (I) avec des boulons de raccordement pour bois (2) tel qu’illustré. Servez-vous de la clé Allen (8) pour serrer les boulons de raccordement.
LITS SIMPLES SUPERPOSÉS Lattes : 8 pièces pour le lit supérieur 8 pièces pour le lit inférieur J H 4 L K I 4 ÉTAPE 10 Insérez deux lattes avec goujons de bois (T) dans les rainures situées au centre des barres latérales supérieures (H et J) du lit supérieur tel qu’illustré. Fixez les lattes sans goujons de bois (L) aux barres latérales supérieures (H et J) du lit supérieur avec des vis à tête plate (4) tel qu’illustré.
LITS SIMPLES SUPERPOSÉS Le premier lit simple Le deuxieme lit simple Pour convertir les lits superposés en deux lits simples, retirez l’échelle et toutes les barrières. Avec l’aide d’une autre personne, séparez le lit supérieur du lit inférieur.
LITS SIMPLES SUPERPOSÉS ATTENTION: Cette unité est destinée à être utilisé seulement avec des produits et/ou les poids maximum indiqués. L'utilisation avec d'autres produits et/ou des produits plus lourds que les poids maximum indiqués peut entraîner une instabilité ou causer des blessures. NE PAS PERMETTRE DE SE CHAMAILLER SUR OU SOUS LE LIT ET NE PAS SAUTER SUR LE LIT. NE PAS PERMETTRE À DES ENFANTS ÂGÉS DE MOINS DE 6 ANS D'UTILISER LE LIT SUPÉRIEUR.