DOREL ASIA Model No.: BUNK BED WM3911-13 WM3921-13 WM3921E2 WM3921B-DC WM3921W-DC-13 WM3921G-DC UPC CODE: 0-65857-15752-9 0-65857-15700-0 0-65857-16529-6 0-65857-16887-7 0-65857-16277-6 0-65857-16785-6 Color PINE LIGHT CHERRY MOCHA BLACK WHITE GREY NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Lot number: (TAKEN FROM CARTON) Date of purchase: _______ / _______ / _______ DO NOT RETURN PRODUCT TO THE STORE.
CUSTOMER SERVICE If you are missing parts or have any questions about this product, contact our customer service representative first! CALL 1-800-295-1980 You can also order parts by writing to the address listed below. Please include the product model number, color and a detailed description of the part. Customer Service Department No. 413 12345 Albert-Hudon Boulevard, Suite 100 Montreal, Quebec Canada, H1G 3L1 E-MAIL: das@dorel.
NOTES * READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH STEP OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN RESULT IN INJURY. * CAUTION: ADULT ASSEMBLY REQUIRED * MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A SMOOTH SOFT SURFACE. * ASSEMBLY WILL REQUIRE TWO PEOPLE. * MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
BUNK BED ALLEN KEY
BUNK BED E
BUNK BED
BUNK BED STEP 1 One of the headboard top crosses (F) has a label on it, do not use it in this step. Insert wood dowels (7) into the ends of headboard top cross (F), headboard bottom cross (G), and headboard center cross (S). Attach top posts (A and B) using wood joint connectors (3) as shown.
BUNK BED STEP 2 Repeat the previous step to assemble the remaining three sets of headboards. Be sure to pair the bottom posts (D) and (E) for one pair; (E) and (D) for another; and the top posts (C) and (A) for the last pair. NOTE: Be sure to use headboard top cross (F) with label attached to it between top posts (A) and (C). See illustration for label orientation.
BUNK BED 1 1 8 8 8 8 K K 8 I I 8 Holes Holes 8 8 1 19 9 STEP 3 Attach the two headboards with bottom posts (D and E) to bottom side rails (I and K) using joint connectors (1) and barrel nuts (8) as shown. Note: This is the lower bunk.
BUNK BED M M 3 M STEP 4 Insert a wood dowel (7) into each end of the long guardrails (M). Attach two long guardrails (M) and two top side rails (H and J) to top posts (A and B) & (A and C) as shown. Fasten top side rails (H and J) with joint connectors (1) and barrel nuts (8). Fasten long guardrails (M) with wood joint connectors (3) . Use Allen key (9) to tighten all joint connectors. This is the upper bunk.
BUNK BED STEP 5 Insert two slats (T) into the center slots of the bottom side rails (I and K) of the bottom bunk as shown. NOTE: Once inserted, there should be three empty spaces left on each side.
BUNK BED STEP 6 Insert slat (L) into remaining holes on the bottom side rails (I and K) on the lower bunk. Secure slats (L) to the bottom side rails (1 and K) with flat head wood screws (4) using a phillips head screw driver (not included). Repeat step 5 and 6 to attach slats (T and L) to the upper bunk. NOTE: Slats (T and L) will be placed between two wooden blocks.
BUNK BED M M RR 55 33 77 NN RR BB M 66 R JJ 3A A 5 B 7 66 R 55 N 6 J HH A 6 5 H CC II C KK K I STEP 7 Place four wood dowels (6) into the holes in the bottom posts (D and E). Stack the top bunk onto the bottom bunk with the help of another person. Insert wood dowels (7) in the ends of short guardrails (N). Attach short guardrails (N) to top post (A) with wood joint connectors (3).
BUNK BED 7 8 PCS 2 8 PCS STEP 8 To assemble the ladder, insert wood dowels (7) into the ends of the ladder steps (Q). Attach long ladder end (O) and short ladder end (P) to ladder steps (Q) with wood joint connectors (2) and Allen key (9).
BUNK BED Slats are not shown in illustration for clarity 2 N H I 2 6PCS STEP 9 Attach the ladder to the short guardrails (N), top side rail (H) and bottom side rail (I) with wood joint connectors (2) as shown. NOTE: If slat (L) is covering the ladder mounting holes, remove slat (L) and replace after the ladder is attached.
CONVERTING THE BUNK BED INTO TWO SINGLE BEDS Remove the ladder and all the guardrails. With the help of another person, remove the top bunk from the lower bunk. Disassemble the side rails from all headboards (top and lower bunks). Re-assemble the headboards (with tall posts) and footboards (with short posts) to side rails. Note: Switching the headboards will allow the two single beds to be identical (the headboards will have taller posts and the footboards will have the shorter posts).
BUNK BED CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED. DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK. BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG TEENAGERS.