Beverage Air 3779 Champion Blvd Winston-Salem, NC 27105 INSTALLATION AND OPERATION MANUAL CF3 Congratulations! You have just purchased the finest commercial refrigeration available. •••• www.beverage-air.
You have selected one of the finest commercial refrigeration units made. It is manufactured under strict quality controls with only the best quality materials available. Your Beverage Air cooler, when installed correctly and properly maintained will give you many years of trouble-free operation. Table of Contents INSTALLATION AND OPERATION MANUAL ........................................................................ 1 APPLICATION ...........................................................................
Warning Child Safety! Destroy carton, plastic bags, and any exterior wrapping material immediately after the freezer is unpacked. Children should never use these items for play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation. A child might suffocate if he crawls into a freezer to hide or play. Remove the door of a freezer when not in use, even if you plan to discard the freezer.
MOVING THE EQUIPMENT Disconnect the power cord plug from the wall outlet. Remove product, then defrost, and clean the freezer. Secure all loose items such as shelves and fix the door by taping it securely in place to prevent damage. In the moving vehicle, secure the freezer in an upright position and cover it to protect the outside of the cabinet. PLACING AND INSTALLING THE EQUIPMENT THIS UNIT CANNOT BE INSTALLED IN ENVIRONMENTS WITH EXPLOSIVE GASES. THE EQUIPMENT IS DESIGNED ONLY FOR INDOOR OPERATION .
ELECTRICAL REQUIREMENTS The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance. The use of extension cords is not permitted and will void the warranty. Before connecting your equipment, check that the electrical data on the data plate match your electrical output. If voltage varies by 10 percent or more, freezer performance may be affected.
UNIT OPERATION SETTING THE TEMPERATURE CONTROL To access the temperature control, the rear grill should be removed using a Phillips screw driver. The temperature control is factory pre-set to provide satisfactory product storage products. However, the temperature control is adjustable to provide a range of temperatures for your personal satisfaction. If a colder temperature is desired, turn the control clockwise. Allow several hours for temperature to stabilize between adjustments.
SERVICE CHECKLIST Before calling for service, review this list. It may save you both time and expense. This list includes common occurrences that are not the result of detective workmanship or materials in this appliance. OCCURRENCE SOLUTION Freezer does not run Check to ensure that freezer is not plugged into a circuit that has ground fault interrupt. If you are unsure about the outlet, have it checked by a certified technician. Temperature control is in the OFF position.
PRESCRIPTIONS, EQUIPMENT PROHIBITIONS AND OTHER USES FOR THE The equipment has been exclusively designed to maintain the proper temperature of packaged food products. Because the unit is not designed to cool the product down quickly, the product must be loaded at its appropriate temperature. Displaying pharmaceutical products in this unit is prohibited. CAUTION - Do not remove grilles or panels that require using tools to be accessed - Do not keep the unit running unloaded.
MAINTENANCE GUIDELINES Regularly and carefully cleaning and defrosting the equipment prevents deterioration and product alteration. REMOVAL OF FROST It is recommended to remove the frost accumulated before reloading the freezer or anytime when one quarter inch of frost has accumulated. The unit will have to be manually defrosted. The manual defrost frequency will depend on the units usage, environment, and the amount of frost accumulated. 1.
Cleaning the Inside WARNING! DAMP OBJECTS STICK TO COLD METAL SURFACES . SURFACES WITH WET OR DAMP HANDS . DO NOT TOUCH THE INTERIOR METAL After defrosting, wash the inside surfaces of the freezer with a solution of two tablespoons of baking soda in one quarter of a gallon (1.1 liters) warm water. Rinse and dry. Wring excess water out of the sponge or cloth when cleaning in the area of the controls, or any electrical parts.
This Page Intentionally Left Blank •••• www.beverage-air.com Pg.
TECHNICAL ASSISTANCE If technical personnel assistance is required, you must immediately contact your distributor, specifying the kind of problem and clearly indicating the equipment model and serial number. If replacing parts is required, do it through your distributor.
