Installation Sheet

B B B
A
C C C C
2
1
3
6
7
4
5
1
2
3
4
5
6
7
1 4 2 2 1 1
1 4 2 2 1 1
1 4 2 2 1 1
1 5 2 2 1 1
5 ⁄”
1”
2 ⁄”
1”1”
Bottom guide
G
(3 ⁄”)
4”
1”
max.
1 ¾”
FOH
finished
opening
height
DGH
door
glass
height
F (3/8”)
Set Casa-System
track rail
wall fixture
(without screws and dowels, at construction side)
bottom guide
(without screws and dowels,
at construction side)
wood door
special tool
(inclusive)
trolley
stopper
track- rail
wooden doors
max. 1-3/4”
max. 220lbs
65_30_00.0202_Casa_wood-02-2017_US
Set / each
Installation instructions
sliding door fittings Casa
for wood door (1-3/8” - 1-3/4”)
B
Inch
FOW
Inch
C
Each
FOH
max. Inch
F
Inch
G
Inch
DGH
max. Inch
(DGH = FOH-F+1”)
A
Inch
install
at right angle
drill
dowel
adjust set
level
perpendicular
measure
mark
measure
clarify question
see instruction
special tool
visual inspection
2 people
required
loosen/
tighten
screw on
Attention
screw on
screw on
Ø 3/8”
2 ⁄”
1”
2-⁄” 2-⁄”
max.
1 ¾”
13/16”
9/16”
5 ⁄”
technical changes reserved - version 02.2017 mm acurate; Inch approx
© by ABP-Beyerle GmbH
Beyerle US L.L.C.
5126 S Royal Atlanta Dr. , Tucker, GA 30084
Phone (770) 349 - 6324 , Fax (770) 934 - 3384 , mail: [e-mail], www.beyerle-us.com
FOH
finished
opening
height
you must check the
position of the wall
fixtures and the door
stopper before
installation!
Warning!
Proper header or mounting
must be installed
for the full length of the
sliding door rail to provide
adequate support because
of the weight of the sliding
door system
20 ¼”
24 ⁄”
29 ½” - 35 ⁄” 98 ⁄” 1/4”- 3/8” 2 ⁄” 99 ⁄”70 ⁄”
35 ⁄” - 39 ⁄”82 ⁄”
26 ¾” 39 ¾” - 44 ⁄”90 ⁄”
22 ⁄”
4
4
4
5
44 ½” - 49 ⁄”100”
98 ⁄”
1/4”- 3/8” 2 ⁄” 99 ⁄”
98 ⁄”
1/4”- 3/8” 2 ⁄” 99 ⁄”
98 ⁄”
1/4”- 3/8” 2 ⁄” 99 ⁄”
70 ⁄”
82 ⁄”
90 ⁄”
100”
FOW finished opening width
Finished floor
Make door handle clearence so that fingers
do not get pinched when the door is used!
X
Beyerle US L.L.C., ABP-Beyerle it´s
subsidiaries and agents are not
responsible or liable for damage or
injury to any persons or property due
to improper installation of it’s products.
All liabilities reside solely with the installer.
Comply with all general safety
regulations when installing the sliding
door fittings!
Installation to be completed by qualified
licensed contractor. Be sure to tighten
all screw connections one week after
starting to use the sliding door fittings!
Check nuts and bolts regularly for
tightness and retighten if necessary!
Never use scouring agents to clean the
sliding door fittings; Rather use
commercially available cleaner!