Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 Page 1 of 32 bf1systems Tyre Pressure Monitoring System – Mini Analyser User Manual F1-100-1451-003 – 433MHz TPMS Mini Analyser, Wireless Version – 1.
Wireless Mini Analyser User Manual 1_04 2 of 32 Wireless Mini Analyser User Manual V1_06 Wireless Mini Analyser User Manual Revision History 1 Modifications Date 03/07/2009 05/08/2009 07/08/2009 27/08/2009 26/10/2009 18/05/2015 RD096 071112 Modifications Document Creation Serial port configuration added Detailed description of ‘last’ command sequence added ‘gencfg’ command description added Setup menu details added MAC_Addr update command revised Bootloader section covers change of Mini Analyser b
Wireless Mini Analyser User Manual 1 2 Wireless Mini Analyser User Manual V1_06 1_04 3 of 32 Modifications ..........................................................................................................................................................................2 Safety Advice.........................................................................................................................................................................4 2.1 MW6288 9V mains charger .................
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 Page 4 of 32 2 Safety Advice 2.1 MW6288 9V mains charger WARNING! Risk of electric shock This product contains no serviceable parts and must not be opened. Do not charge any other type or chemistry of rechargeable battery cells other than Alkaline, NiMH and NiCad. This product must not be used outside. Do not expose the charger to rain or moisture to avoid the risk of fire or electrical shock.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 5 of 32 2.2 EMSA 5W USB Series Power Supply WARNING! Risk of electric shock This product contains no serviceable parts and must not be opened. This product must not be used outside. Do not expose the power supply to rain or moisture to avoid the risk of fire or electrical shock.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 6 of 32 2.3 Wireless mini analyser CAUTION! Do not use the wireless mini analyser if there is any damage to the battery terminal or wire. Only use the power cables that have been supplied with the wireless mini analyser. NOTE RD096 071112 Remove battery from the device when not used for a long period of time.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 7 of 32 3 Inventory The system will arrive with the following items: Description Wireless Mini Analyser 9V Battery Snap to 2.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 8 of 32 5.1 Battery Charger A 230V AC - 9/9.8 V DC Battery Charger is supplied with the Wireless Mini Analyser. The unit can charge 2 rechargeable 9V batteries and includes the following features: LED status display, micro controlling trickle charge mode, a discharge function, and delta V detection Intended use: This product is intended for use only in dry interior rooms.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 9 of 32 5.2 USB mains power supply The USB mains power supply is supplied with the purpose of supplying power directly to the wireless modules that are used with the mini analyser. The power supply converts 230V AC mains voltage into 5V DC at 1.0A The power supply should only be used in conjunction with the USB cables that have been supplied with the mini analyser.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 10 of 32 5.3 Wireless Mini Analyser The Wireless Mini Analyser is fitted with a rechargeable battery in order to maximise the performance and versatility of the device. A jack socket on the side of the unit allows it to be charged using the mains charger provided. Pin 9 of the 9-way D-type fitted to the Wireless Mini Analyser has been wired to provide power for the Analyser Module unit when in use.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 11 of 32 5.4 Mini Analyser battery To remove the battery compartment lid The battery and antenna can be found stored Press the release clip and lift away. within the battery compartment. LIFT PRESS It is advised that the battery terminal cover is placed onto the battery during transit to avoid shorting of terminals.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 12 of 32 5.5 Attaching the Antenna The wireless mini analyser is supplied with a detachable antenna which can be found and stored in the battery compartment. Attach the antenna simply screw it clockwise onto the antenna connector located on top of the mini analyser. The antenna should only be finger tight – Do not use any tools as this will result in damage to the antenna or connector.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 13 of 32 5.6 Wireless Modules 5.6.1 Wireless Module The Wireless Module is fitted with a 9-way D-type, which connects directly to the 9-way D-type fitted to the bottom of the Mini Analyser. When connected in this way the Wireless Module is powered directly from the Mini Analyser.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 14 of 32 5.6.2 Wireless PC Module The Wireless PC Module is fitted with a 9-way D-type, which can be connected directly to the 9-way D-type serial connector on a PC. A straight through serial extension lead should be used to remotely connect the Wireless PC module. The Wireless PC Module settings may be updated with the unit connected to the PC serial port.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 15 of 32 5.6.3 Status Information Both the Wireless PC Module and Wireless Analyser Module have 2 LEDs that are used for indicating the status to the user. The red LED pertains to power while the orange LED relates to wireless link status. 5.6.3.1 Power LED The power LED has three modes of operation: Continuously on : Power on, unit initialising Blink : Power on, initialisation completed ok, operating normally (0.3s on – 2.
Wireless Mini Analyser User Manual 1_04 16 of 32 Wireless Mini Analyser User Manual V1_06 At power on the co-ordinator node (Wireless PC Module) enters pairing mode (fast flashing Link LED). In this mode it listens for any programmed device that is in range. When an end device node (Wireless Analyser Module) is powered on it also enters pairing mode (fast flashing Link LED).
Wireless Mini Analyser User Manual 1_04 17 of 32 Wireless Mini Analyser User Manual V1_06 As each wheel is learned, the serial number of the sensor that has been assigned to the wheel will be shown on the Mini Analyser display. Unassigned locations will display serial number ‘0’. ▲ ▲ ▲ ▲ F F R R L R L R : : : : 2 0 1 3 8 1 5 5 6 9 0 0 0 ▲ ▲ ▲ ▲ This process is repeated for each corner of the vehicle.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 18 of 32 6.2 Data Transfer Transfer of the data collected by the Wireless Mini Analyser is achieved via the wireless serial link provided by the Wireless PC Module and Wireless Analyser Module. The wireless modules provide a transparent 19200-baud serial link between the host PC and the Mini Analyser.
Wireless Mini Analyser User Manual 1_04 19 of 32 Wireless Mini Analyser User Manual V1_06 On receipt of the ‘ack’ message the Wireless Mini Analyser will return to the USER1>, ready for the next host command.
Wireless Mini Analyser User Manual 1_04 20 of 32 Wireless Mini Analyser User Manual V1_06 6.2.4 ‘gencfg’ Command By default the Wireless Mini Analyser is configured to auto detect and decode RF datagrams from Ge1, Gen2 and Gen 3 sensors. In some situations the user may wish to configure the unit to receive only sensors of a specific type. This can be achieved via the ‘gencfg’ terminal command.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 21 of 32 6.3.1 Power Settings The selection page allows the user to configure the automatic power controls for the Mini Analyser. The selection page is entered by pressing the power button at the menu page.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 22 of 32 6.3.3 Beep / LED 2 The selection page allows the user to configure the indicators for LF transmissions by the Mini Analyser. The selection page is entered by pressing the power button at the menu page.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 23 of 32 6.3.4 System Info The System Info pages provide details regarding the Mini Analyser hardware and software. The display pages are entered by pressing the power button at the page. Setup System Info Up Ok Down Diags Temp:0.00 3V:3.308 Ref:5.00 5V:4.995 Vbat:10.0 Up Exit Down Software Part No F1-37-9885 Version 1.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 24 of 32 Channel Config The selection page allows the user to select the sensor types that the Mini Analyser is capable of decoding. The selection page is entered by pressing the power button at the menu page.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 25 of 32 7.1 Wireless Analyser Module The cParameters in the Wireless Analyser Module that may be updated by the user are: Network ID [PAN_ID] Co-ordinator MAC address [C_MAC_Addr_1] Link activity timeout [Link_timeout] To make changes to any of these parameters the commands detailed below may be used. 7.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 26 of 32 7.3.3 Link_timeout The user command for changing the link timeout held within the cParameter table shall have to following format: Link_timeout – 16 bit decimal value for Link_timeout setting, expressed in seconds eg: Link_timeout 15 Result: Link_timeout is set to 15 seconds Typing the Link_timeout command with no argument shall report the current Link_timeout setting. 8 Bootloader 8.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 27 of 32 The Mini Analyser communication speed is now correct to function with the bf1systems Analyser Bootloader software. Close the terminal emulator and start the bootloader software. The screenshot below shows the bootloader software. The following steps should be followed to update the firmware: Ensure a known good battery is used or the analyser is powered from the charger during the update.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 28 of 32 9 Wireless Analyser Module Specifications 9.1 General Parameter Units Conditions Supply Voltage V Power supplied to module via Pin 9 on the 9-Way D Connector or by the Mini USB connector Supply Current mA Min Typ Max 5 50 9.2 Communications Parameter Data Rate Units Conditions Min kbaud Typ Max 19.2 Protocol 2.4GHz IEEE802.15.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 29 of 32 Important Notice User information according to FCC15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. b) Statement for Class B digital device acc. to FCC 15.105 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Wireless Mini Analyser User Manual 1_04 30 of 32 Wireless Mini Analyser User Manual V1_06 Wireless PC Analyser Module Specifications 9.4 General Parameter Units Conditions Min Supply Voltage V Power supplied to module via Pin 9 on the 9-Way D Connector or by the Mini USB connector Supply Current mA Typ Max 5 50 9.5 Communications The implemented IEEE 802.15.4 based network operates in the 2400 MHz (2.4GHz) radio frequency band.
Wireless Mini Analyser User Manual Parameter Data Rate Communications Range Transmit Power Level Receiver Sensitivity Protocol Wireless Mini Analyser User Manual V1_06 Units kbaud m dBm dBm Conditions 1_04 31 of 32 Min Typ 19.2 50 Max 2.5 -96 2.4GHz IEEE802.15.4 Compatible 9.
Wireless Mini Analyser User Manual Wireless Mini Analyser User Manual V1_06 1_04 32 of 32 10 Charger MW 9V MW6288GS 10.1 Specifications Input (VAC) Output (VDC) Output (W) Output (mA) Protection/IP Class Tech Fitting size 230 @ 50Hz 2x 9.8 1.4 Max 70 II / IP20 Ni-Cd Ni-MH 2x 9V Block 11 EMSA050100 USB power supply 11.
