Operating Instructions and Installation Instructions

SK LINE G-690 / G-690TV
sportkoncept
13
12-Do not overexert yourself or exercise beyond
your capabilities. Stop exercising immediately if you
are in pain or feel strange, and
seek professional
medical advice
.
13-To prevent the risk of electric shock keep
liquids away from all electrical components (motor,
switches, etc.). Do not rest anything on the casing,
the treadmill belt or the electronic monitor. Place
liquids on the storage rack inside the appropriate
container.
14-Do not use the equipment if it is damaged,
does not work correctly or if it has been dropped
from a height or fallen in water. Take the
equipment to a technical service centre to have it
checked and repaired.
15-Make sure that the mains supply voltage is
suitable for the machine before plugging it in. The
mains voltage output must be 220 V-240V and the
electric socket must have the same pin layout as
the plug. If this is not the case, please consult your
technical service centre.
16-The equipment must only be connected to
electrical circuits with an earth connection. If
not, the user risks receiving an electric shock.
Make sure that the electric mains socket has the
same pin layout as the plug on the appliance Fig A.
17-Do not use the machine if the mains cable
becomes damaged or worn.
18-Do not tug on the mains cable in order to
unplug the unit.
19-Keep the plug and mains cable away from hot
surfaces.
20-Do not use the equipment in areas where
aerosol sprays are used.
21-Do not use the machine outdoors.
22-Do not attempt any maintenance and/or repair
work other than that stated in this manual. For
more complicated tasks, please get in touch with
your technical assistance service.
SAFETY BREAKER
This model is equipped with an electronic circuit
breaker to protect both the electronic and electrical
circuits.
This safety device will be automatically triggered if
the unit is subjected to abnormal force or heat.
Should this occur:
1.- Set switch (L), located on the casing, to the “0”
(OFF) position Fig B.
2.- Press the circuit button (C) to reset the unit.
3.- Next, set switch (L) to the “I” (ON) position and
the unit will be ready for use again.
Should the circuit breaker trip repeatedly then the
most probable causes are:
- Abnormal working conditions,
- Treadmill belt in need of lubricant,
- Solvent based lubricants used (use BH type),
- Belt is too tight.
Plug the unit into a wall socket with an EARTH
terminal. Set switch (L) to Position [1].
Fig B
ASSEMBLY INSTRUCTIONS
Take the unit out of the box and place it on the floor
as shown in Fig.1.
ATENTION: The assistance of a second person is
advisable for the assembly work
Make sure that all of the pieces are there: (A)
Monitor; (B) Main body; (C) Handrail handlebar; D)
Left-hand focus bar; (E) Right-hand focus bar; (F)
Rear cover for monitor; (G) Bottle; (a) Screw M-
10x70; (b) Screw M-5x10; (c) Nut M8; (d) Screw M-
4x10; (e) Screw M-4x12; (f) Switch; (g) Star drive
spanner; (h) Bottle of lubricant; (i) Mains connection
cable; (j) Combination spanner; (k).
TV support
plate ( Mod G-690 Tv ; (l) Remote control unit( Mod
G-690 Tv ; (m) Allen key.
Follow the assembly instructions step by step:
1 First loosen off the screws (b) on the motor cover
(Q), Fig.2.
Next, insert the focus bar into the bottom right-hand
support on the structure and secure by using screws
(a).
2 Now take the left side bar (E) and insert it into the
bottom left-hand support on the structure and use
screws (a) to secure it.
At least two people are needed for this step.
3 When fitting the side bars, one person should hold
the side bar while the other one fits the screws (a).
This will prevent any possible accidents.