Audia® & Nexia® RED-1 & RED-1F Operation/Installation Manual Biamp Systems, 9300 SW Gemini Drive, Beaverton, OR 97008 U.S.A. (503) 641-7287 www.biamp.
table of contents remote ethernet device 1 (red-1) FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Setup and Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 front panel. . . . . . . . . . . . . . . . .
remote ethernet device 1 (red-1) RED-1 Remote Ethernet Device is a remote control for Audia® and Nexia® systems. It offers a simple, intuitive interface for end users and can be installed and configured to fit the unique needs of a particular application. The device connects via standard Ethernet cabling and is powered over Ethernet, eliminating the need for custom cabling and local power sources. Multiple remote control panels can be connected over large distances using standard network technology.
red-1 front panel Select Scroll Latch Setup and Use The Audia and Nexia software provides an intuitive interface for setup and programming of the RED-1. The information supplied by this manual relates to physical connections and device setup. For more details on software setup, please consult the Audia or Nexia Help File.
red-1 back panel Connectors Two Ethernet connectors—one rear-facing RJ45 and one top-facing insulation displacement connector (IDC)—are provided for connecting to the network. Only one connector may be used. The RJ45 and IDC utilize unshielded twisted pair (UTP) wiring to connect to an Audia or Nexia system. This connection is made to the Ethernet port of an Audia or Nexia unit, either directly (single station) or via a network switch, and carries control data over Ethernet.
red-1 set up Device Setup Mode The RED-1 can be configured without connecting to a functional Audia or Nexia network. To enter setup mode, connect the RED-1 to a PoE source and place the jumper or any metal object across the locksmith pins. When configuration is complete, remove the jumper and attach it to only one pin to resume normal operation. Please note: many of the configuration settings can be accessed via the Audia or Nexia software.
red-1 set up Edit Device ID To name the unit, scroll to the ID Tag icon and press the Select button. Use the scroll wheel and Select button to choose the desired characters. The Device ID must match that of a corresponding block in the Audia or Nexia design. More than one unit may be identified with the same design block (same ID). Device IDs may also be assigned via Device Maintenance in the Audia or Nexia software.
red-1 set up Edit Display Brightness To change the brightness of the OLED panel, scroll to the Display Brightness icon and press the Select button. Use the scroll wheel and Select button to make adjustments. The first setting represents the normal operational display brightness, and the second setting represents the dim display brightness. Display brightness cannot be assigned via Device Maintenance in the Audia or Nexia software.
red-1 installation Surface Mount Installation The RED-1 surface mounts to most walls and has a wide variety of mounting holes that accommodate standard US and International back boxes. 84mm 3.3" USA, Japan, Australia 60mm 84mm 2.36" 3.3" EUR including Germany, Sweden, UK, Netherland Italy Use a screw driver or other suitable tool to engage the latch at the bottom of the RED-1 to detach the back enclosure.
red-1 installation Flush Mount Installation The RED-1F may be flush mounted using the retro-fit plate (provided with the product) or a Raco™ 254 box (purchased from an electrical distributor). To install the RED-1F, a hole must be cut in the wall to accommodate the Raco™ 254 back-box or to use the retro-fit plate. See the figures below. 11.75cm 4 5/8″ 4 3/4″ 12.
red-1 installation Retro-Fit Plate Raco™ 254 Trim Ring Front Plate Exploded view showing pieces required for mounting to the retro-fit plate or the Raco™ 254 back-box When installing the RED-1F using the retro-fit plate or the back-box, fasten the trim ring using the four screws provided to either the retrofit plate or the back-box.
red-1 installation Connect the wire according to the color code silkscreened as text next to the IDC or as shown on the label on the back enclosure (see figure below). The color code uses the T568A standard for wiring. When using the T568B wiring scheme, please note that the orange wire pair (OR and WH/OR) and green wire pair (GR and WH/GR) need to be swapped. After inserting the wires, press the tabs until the insulation is punctured with an audible click. No wire stripping is necessary.
red-1 specifications SPECIFICATIONS (RED-1) Dimensions (Length x Width x Depth): 5.1 inches x 4.7 inches x 1.25 inches (130mm x 120mm x 32mm) Weight: 0.5 lb Power consumption: PoE Class 1 (3.2W max) Material: PC/ABS Control cable requirements: Unshielded twisted pair (UTP) wiring, 100BaseT interface using either RJ45 or Insulation Displacement Connector (IDC) Control cable length: 330 ft.
red-1 warranty BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below.
ec declaration of conformity DoC RED201007 EC Declaration of Conformity Biamp Systems Corporation, as manufacturer having sole responsibility, hereby declares that the following described product complies with the applicable provisions of the DIRECTIVES below except as noted herein. Any alterations to the product not agreed upon and directed by Biamp Systems Corporation will invalidate this declaration. Product Models: RED-1, RED-1F Product Description: Control Accessories for use with audio DSPs.
compliance (This information is presented to comply with the requirements of Chinese law SJ/T11363-2006)” 有害物质表 Biamp Systems Corporation 远程控制设备 (Remote Control Device) RED-1, RED-1F 部件名称 设备机箱 (Equipment Chassis) 手册和其他书面文档 (Manual and Paper Documents) 包装箱和所有包装材料 (Box and Packing Materials) Pb 铅 X O O Hg 汞 O O O 有毒有害物质或元素 Cd Cr+6 PBB 镉 六价铬 X O O O O O O O O PBDE O O O 0：表示该部件所有均质材料中的这种有毒有害物质低于 SJ/T11363-2006 的限制要求. X：表示该部件中至少有一种均质材料所含的这种有毒有害物质高于 SJ/T11363-2006 的限制要求.
