Vocia® VA-2060, VA-2060e, VA-4030, VA-4030e Manual January 2013 Biamp Systems, 9300 SW Gemini Drive, Beaverton, Oregon 97008 U.S.A. (503) 641-7287 www.biamp.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this product near water. 6) Clean only with dry cloth. 7) Do not block ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other product (including amplifiers) that produce heat.
TABLE OF CONTENTS VOCIA AMPLIFIER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 VA-2060, VA-2060e, VA-4030 and VA-4030e. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . .
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e The VA-2060, VA-2060e, VA-4030 and VA-4030e are digital networked multi-channel audio amplifiers designed for use in Vocia systems. All models are CobraNet® enabled and feature either two or four channels of amplification, with on-board DSP. Channel-to-channel or device-to-device failover may be user configured. Each amplifier channel has user selectable support for 4 or 8Ω operation or Constant Voltage operation of 25, 70 or 100 Volts.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FRONT PANEL System Indicators The LED indicators on the front panel of the amplifier provide information and operational status of the amplifier and its associated output and input channels. LED layout and features vary between amplifier models. LEDs are grouped to show chassis and amplifier channel status indication. Please see the Front Panel View section for details on the different configurations between the various amplifier models.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FRONT PANEL Channel Indicators Amp Channel Indicators These indicators relate to each amplifier channel: Amp Fault is a yellow LED that illuminates when a channel fault has occurred. Two types of channel faults can be reported depending on the severity of the problem. Flashing yellow indicates a Warning, which means that some aspect of the amplifier module is not performing within normal specification.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FRONT PANEL VIEW VA-2060 VA-2060e VA-4030 VA-4030e 6
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Rear Panel BIAMP SYSTEMS assembled in the USA www.biamp.com CAUTION 10 0832-CPD-1401 N24138 RISK OF ELECTRICAL SHOCK. DO NOT OPEN. 52SJ Analog Inputs 4 100-240V~ 50/60Hz 3 2 60 Watts YEL: In Use / Conductor Pri. Sec.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Table 1. CobraNet LED indication Left LED Right LED Description None None No data connectivity or CobraNet activity None Flashing Green Link Established. Typically seen on Secondary connection that is in standby.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Amplifier Output Connections CAUTION: All speaker wiring connections and output load selection should be made by qualified personnel and with the amplifier power removed. The 100V output requires Class 3 wiring. Please refer to a qualified electrician or other qualified person according to local codes.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e REAR PANEL Output Fault Detection The Amplifier monitors (supervises) for faults on speaker connections using a combination multiple out-of-band (inaudible) high frequency tones for end-of-line detection, and DC current for ground fault detection. For end-of-line detection, one or more (up to 15 maximum) ELD-1 units must be connected to the end/s of the speaker line.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FAILOVER MODES Failover Modes The Vocia amplifiers support a device-to-device or channel-to-channel failover mode. Only one type of failover mode can be implemented per amplifier. Device-to-Device Failover All amplifiers support device-to-device amplifier chassis failover in case of fault. The redundant amplifier must be the same model as the primary amplifier.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e FAILOVER MODES Channel-to-Channel Failover All amplifiers support channel-to-channel failover. This is configured in the Vocia software in the amplifiers general setting as 1:1 Failover. In this configuration, channel pairs can be specified and adjacent channels will act as a redundant backup. Channel 2 will act as backup for channel 1. For the VA-4030 and VA-4030e models, channel 4 will act as backup for channel 3.
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e SPECIFICATIONS Vocia Amplifier 2060 / 2060e / 4030 / 4030e SPECIFICATIONS Message Memory: Network Audio: Network Connections: Analog Inputs: Nominal Input Range: Maximum Input Level: Equivalent Input Noise: Dynamic Range: Input Impedance: Phantom Power: Frequency Response: Signal to Noise Ratio: THD + Noise: Rated Output Power: VA-2060: VA-2060e: VA-4030: VA-4030e: Supported Loads: Low Impedance: Constant Voltage: Output Configuration: Output DC Offset:
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e BLOCK DIAGRAM 4030e and 2060e Amplifiers 4030 and 2060 Amplifiers 14
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e CURRENT DRAW AND HEAT OUTPUT VA-4030 and VA-4030e Specifications 1/8 POWER PINK NOISE IDLE 1/3 POWER PINK NOISE FULL POWER SINE WAVE Total Output Power (Watts) Channels Used Input Power Watts BTU /hr Input Power Watts BTU /hr Input Power Watts BTU /hr Input Power Watts BTU /hr 30 1 30 102 36 110 46 123 88 198 60 2 30 102 41 114 62 143 133 242 90 3 30 102 47 122 77 160 179 304 120 4 30 102 54 133 93 181
VOCIA AMPLIFIERS VA-2060, VA-2060e, VA-4030, VA-4030e WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below.
FCC COMPLIANCE FCC NOTICE - CLASS B DIGITAL DEVICE NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential as well as in a commercial installation.
COMPLIANCE DoC VA2201106 EC Declaration of Conformity Biamp Systems Corporation, as manufacturer having sole responsibility, hereby declares that the following described product complies with the applicable provisions of the DIRECTIVES below except as noted herein. Any alterations to the product not agreed upon and directed by Biamp Systems Corporation will invalidate this declaration.
COMPLIANCE RoHS COMPLIANT This Biamp product, including all attendant cables and accessories supplied by Biamp, meets all requirements of EU Directives 2002/95/EC of January 27, 2003, and 2005/618/EC of August 18, 2005, the EU RoHS Directives. An EU RoHS Materials Content Declaration document may be obtained at www.biamp.com (This information is presented to comply with the requirements of Chinese law SJ/T11363-2006) !"#$% (Hazardous Substances Table) Biamp Systems Corporation &'()*+,-.
