Model No.
Table of Contents Must Read Before Use ------------------------------------------------------ 2 Certification------------------------------------------------------------------ 2 General Information--------------------------------------------------------- 3 Introduction------------------------------------------------------------------ 3 Product Components (Accessories)----------------------------------------- 3 Product Overview Speaker ---------------------------------------------------------------- 5 Microp
Must Read before Use I Note I * * * * Do not put metallic or sharp material like a pin or a needle into the speaker when using M6. Do not try to put apart this product or fix it yourself Do not leave Sprek inside a vehicle in hot summer or cold winter. If you leave Sprek inside a closed car for long time, it could result in deformation, malfunction or product damage. * Please use only Bicom’s charger or cable when using or charging Sprek.
General Information Wireless Mic rophone * Check there are all product components before using it. * Read through this manual to learn how to use it * If the microphone is facing the speaker, feedback could occur, so try not to face it toward the speaker. * If you set volume high at a narrow space, feedback could occur, so please check if you set the volume right before using it. * Check the battery level often when using it. We recommend charging it when battery level bar level is below “ 2 “.
Introduction Sprek is a wireless speaker & microphone. Sprek is designed to amplify your voice so crowd can hear your voice clearly from distance. Sprek works the best as a teacher’s portable amplifier. Also, using 900MHz which is usually not overcrowded, Sprek has no risk of 2.4GHz interference. It offers remarkably good sound performance with a compact and light body. So, it helps distribute your voice evenly across broad area.
Image Main Device LED Power / Battery Level Power On.
Wireless Microphone Strap Hanger Input Terminal Status Display Power Channel Up Volume Up Channel Down Volume Down Boom MIC Charging Terminal I How to Use Boom MIC I 1 Insert the Boom MIC into the termi nal 2 Insert a head-microphone into the terminal -06-
Speaker Power ON / OFF Turn as shown below until you hear sound Power on Power off - Power is on if you turn the switch to the "+" direction - Power is off if you turn the switch to the "-" direction ※ Note If left not used for an half hour, the speaker automatically goes to power-saving mode. I Speaker LED I LED blinks differently depending on wireless microphone connection When a microphone is connected, LED blinks twice quick. When a microphone is not connected, LED bli nks slowly..
Microphone ON / OFF Microphone is turned on, if you press & hold the power button for two seconds. Microphone is turned off, if you press & hold the power button for two seconds again.
Remaining Battery Level Battery LED below indicates the current remaining battery level. When battery is running low, battery low audio comes out apart from the battery LED. Recharge the battery when battery is running low.
Volume I How to Set Volume I Volume Up Volume Down Total Volume = Speaker Volume x MIC Volume I Microphone Volume I How to Set Volume from Microphone Mute on / off 0.5 Sec Volume Up or Down 0.
Microphone Number Setting [ for Two MICs ] There is no need to do microphone number setting when using one microphone. However, to use two wireless microphones, each microphone needs to be given its own number t o prevent interference with one another. I Set the second microphone to number 2 for two microphone use I 2 Sec Together Set to number 2 by pressing c hannel up button short. Press power button short to complete ※ Note Of two microphones set only one microphone to number “2”.
Pairing between Speaker and Microphone [ for two MICs ] For two microphone transmission, two microphones need to be paired with a speaker. 1 Go to Microphone Pairing Mode 2 Sec Together You can go to pairing mode by pressing & hold power button for 10 seconds as well.
2 Go to Speaker Pairing Mode Turn on the speaker while pressing&hold pairing button. Press&hold the pairing button until the sound of “Pairing” comes out. Power On 3 Once pairing is done, the red LED below is slowly turned off.
Channel Setting You can change channel number between 0 and 9 to avoid frequency interference. When using two microphones, you need to set them to same channel number. I Microphone Channel Setting I 2 Sec 1 Go to Channel setting mode 0.
Reset (in case the speaker is unresponsive or malfunctions) * Press “RESET” button when power is on. Then speaker re-boots. “RESET” button stays inside so use something sharp to press it.
Microphone Reset Press Channel down and Volume Up together 1 Together 2 0.5 Sec Press&hold “Power” button for two seconds. 2 Sec ※ Note Be careful not to press Channel down and Volume up t ogether when a microphone works normally.
How to Charge Speaker and MIC Together Speaker: Battery LED turns orange while being charged and turns green once charging is complete. Microphone : Blue and red appears together while being charged and turns blue once charging is comp te Charging Charged Charging Charged ※ Note • Please use only the included-charging adapter. • When using a smartphone’s charger, make sure to use a 5V/2A charger • We do not recommend charging it with the power on.
Specifications Frequency Transmission Method Modulation System Battery Battery Life Time Charging Time Working Temperature Size Weight Frequency Response Speaker Output 902 MHz~928 MHz TDMA FSK Rechargeable Li-ion 3.7V /3,400mAh Battery for Speaker Rechargeable Li-ion 3.7V / 650mAh Battery for Microphone 24 hours for speaker at stand-by or 10 hours at constant use 9 hours for microphone at constant use 6 Hours for Speaker / 2 hours for microphone -10/+50℃ Speaker : 105mm(W) / 105mm(H) / 40.
Product Warranty Thank you for purchasing our product. Product Name Model Name Simeon Sprek Transmitter : Simeon Sprek T Speaker : Simeon Sprek R Serial Number Warranty Period 2 Year Purchase Date Make sure you fill in all the blanks. This product has passed the strict quality test and in case of b reakdown, the warranty will cover product repair as stated in the Product Warranty. You may requ est product repair to agency or headquarters from which you purchased this device.
www.ez-tok.
