Safety notes 5 to properly use the product. Warning Prohibition Compulsory observance Note Failure to operate pursuant to the above-mentioned warning signs may result in injury or life-threatening risk. including children) who are deficient in body, perception, intellectual capacity, or prurience and common sense (including children} are cognized. Limitad ability and(or} lack of knowledge necessary to us the device without supsrvision.
Safety notes Do not plug/ pull the power plug when the hand is wet. © May result in electric shock. ( a Only suitable for the power in Ensure that the water,cleaning technical specification;|t is strictly agent or urine does not wat prohibited to use excessive loads the power plug. on the same socket. ® May result in overheating ® May result in fire or or fire. electric shock. not pull the power plug/ power Do not use a loose socket. cord at will. # May result in fire or electric shock.
Safety notes Do not disassemble, repair and Please unplug the power edify products by without supply when cleaning the authorization. product. ® May result in fire or electric shock. ® May result in electric shock. Please don't keep the lighted Do not bend or twist the cigarette or other combustion water supply hose. rems near the product ® May result in fire. ® May result in water leakage. Q Do not place heavy objects on Do not invert product.
Use precautions ~ Do not place this product in direct The room temperature of toilet shall be sunlight. above 0°C. ® it may causal product discoloration ® Otherwise, it is possible to freeze and failure of seat heating function. the product. Use warm air and other methods te improve the temperature in the toilet. op Do not shower urine on the bidet Please not use substandard power supply. body and nozzle. © May result in blockage. ® May cause product failure.
Product description The BM-700U-E comes with a dry function, the BM-7005.
Component description 1.Cover plate 2. Installation template 3.Fixation part = fi = Connecting bolt (2} Adjustment sheet {2) Plastic TAB{2) Fixing plate Rubber bushing(2} 5. Water inlet hose 6.
Installation steps Installation tools Noel OB Cross screwdriver Monkey wrench Barrel and rag ‘Water pressure range: please follow the instructions. 2.Corner valves shall be located close to the location where this product is installed and disassembled. 3.Please use the braided hose that comes with the product to prevent water leakage. 4. When Installing braided hose,be careful to prevent the black gasket falling out. Installation Procedure 1.Loosen the nut connecting and removal 2.
Installation steps 6.Close the water valve; (@When the ceramic is similar to the figure above, we suggest connecting the straight end of the hose ta the cover || ef (©When the ceramic is similar to the figure above, we suggest connecting the elbow end of the hose to the cover European ceramic ~ 8.
Installation steps 9.0pen the angle valve to check for 10.Turn on the knob to check whether water leakage; the nozzle is protruding; Bb 11.
Function introduction bs SLUT 1. Make sure the plug Is dry before power supply is connected. 2. After the power supply is connected, the "bi~ Indicates that the cover can be used normally. 3. Water temperature by default at low gear position: about 35°C. 4, Seat temperature by default at low gear position: about 33°C. 5. After the power supply is connected, the knob light and night light are constantly on.
Function introduction & The BM-700U-E comes with a dry function, the BM-7005E does not ELT ET RE Lighting Lighting ping born \ 7, OFF LOW HIGH L Water/wind temp. setting key ~~ Seat temp. setting key Repeatedly press (5) will switch over water temp. in the sequence indicated in the left figures. = Change water temp. :a short sound. 6 Turn off water temp. :a long sound. HGH} grow ® low : about 35°C L a” high : about 38°C. J ~ Low « Repeatedly press {i5) wil switch over wind I 3} temp.
Optional description According to the actual demand, the product provides different configuration scheme: Control button lt 1. control light 2. control rinse 3. control warm wind Ly @ 1@ Without this configuration, the knob light is canceled and night light can be controlled by pressing two function keys at same time Booster module 1. booster 2. massage rinse Without this configuration,no massage rinse seat sensor 1. Low temperature scalding protection 2, Anti-splash function 1.
Cleaning and maintenance Manual cleaning of spray tube Gently pull out the nozzle and dip the neutral detergent with a soft cloth, sponge or small brush. Gently support the nozzle, wipe the spray tube and nozzle.
Cleaning and maintenance Check the leakage protector regularly, at least once a month. Inspection method: Press leakage protector Reset, tha indicator light is on, and the power supply is on. Press the "Test" key of leakage protector, the indicator light is off, and the power supply is disconnected. When the operation is completed, the corresponding error indication information appears, stop using the product, contact the local supplier or call the service hotlink to replace the leakage protector.
Faults and solutions O1@ Pros and hold seat temp chatting kay for 3 sands located an tha aids of the bidet Check power supply Check water supply 1 water supply s nude normal sate 1; power cup ls under normal stats 20 rot actor trips 2. if comer valve is Dion or 3 Manna] reset thermostatically steps) The leakage protector trips frequently note: When water Leakage occurs, close the angle valve and cut off the power supply.
Faults and solutions continued. Night it Ia not ON Night light Is turned off or damaged | Reconnect to the paws supply.
Product technical specification [1] Dec: Mode! BM-7005-E-111 Rated voltage 120V-~, 60Hz 7050W Rated power (inlet water temperature 155°C, flow at 600m//min) Max. transient power 1550W Length of power line Default = 1.5m Water supply pressure 0.1 ~ 0.
