INSTALLATION GUIDE INSTALLATION GUIDE
READ AND SAVE THESE INSTRUCTIONS Technical Specifications Check the fan label to make sure it is the correct voltage. Operating voltage Diameter Weight Operating frequency 120 VAC, 1 Φ 52 in. (132 cm) 11 lb (5 kg) 60 Hz 220/240 VAC, 1 Φ 52 in. (132 cm) 11 lb (5 kg) 50/60 Hz Tools Needed • • • • • Ladder Wire Strippers Phillips Screwdriver Hex Key Wrenches Scan or visit resources.haikuhome.
PARTS a Mounting Bracket b Control Box c Wiring Cover d LED Diffuser Ring e Mounting Ball & Hardware f Lower Cover Trim g Lower Cover Ring h Extension Tube i Motor Unit j (3) Airfoils k Remote Control l Hardware Pack a b d e f g l h k j HAIKU® BY BIG ASS FANS c i 1
HARDWARE Hardware and tools needed for installation are packaged in the hardware pack. Hardware below shown at actual size. Lower Cover Hardware Airfoil Hardware Wiring Cover Hardware or White (6) M5 Screws with Tooth Washer Mounting Hardware Black (2) Painted M3.5 Screws (4) M4 Socket Head Cap Screws Mounting Ball & Hardware Wedge M8 Bolt 2 M8 Washer M8 Nylock Nut 4 mm Self-Tapping Screw Steel Pin Mounting Ball REV.
1 PREPARE THE FAN SITE Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable performing electrical work! 1 Disconnect Power! Disconnect power to the fan location before wiring fan! If required by your local electrical code, a licensed electrician must install the fan. A means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
2 INSTALL THE MOUNTING BRACKET b a c 4 Installation may vary. Refer to the outlet box instructions. REV.
Secure the mounting bracket (a) to the outlet box (b) with the screws supplied with the outlet box (c). Outlet Box Hardware: c. Screw (supplied with outlet box) Sloped Ceilings If mounting to a sloped ceiling, install the mounting bracket so that the open side faces upward with the slope.
3 PREPARE THE AIRFOILS SELECT LENS (BLACK FANS WITH LIGHTS) a MATCH AIRFOIL STICKERS b 1 6 2 REV.
1 Black fans with lights: For softer lighting, remove the white lens and install the smoky lens before attaching the airfoils. a. Twist to uninstall white lens. b. Twist smoky lens to lock in place. 2 Make sure the stickers on the airfoils match the stickers on the fan hub.
4 INSTALL THE AIRFOILS INSTALL AIRFOILS FANS WITHOUT LIGHTS c d a b 1 8 2 REV.
1 Rest the motor assembly (a) on your lap. Moving clockwise, install each airfoil (b) with the provided hardware. Tighten the screws to 2.5 N·m (22.1 in·lb). Do not use power tools to install the airfoils, and do not over-tighten the screws! Over-tightening the screws may cause the airfoils to warp and void your warranty. Airfoil Hardware: c.
5 INSTALL THE LOWER EARTH/GROUND WIRE POSITION EXTENSION TUBE SECURE EARTH/GROUND WIRE a b c d 1 10 2 REV.
1 Lower the extension tube (a) onto the motor shaft. Ensure the yellow arrow sticker on the extension tube is aligned with the sticker on the motor. 2 Remove the screw and ground tag from the motor shaft. Secure the Earth/Ground wire to the motor shaft with the captive screw (b). Connect the yellow Earth/Ground female spade connector (c) to the male connector (d) on the motor.
6 CONNECT MOTOR WIRING AND SECURE EXTENSION TUBE INSTALL WIRING HARNESSES SECURE HARDWARE REMOVE SLACK d a b e a c 1 12 2 3 REV.
1 Remove the tie holding the wiring harnesses to the extension tube. Plug the two large wiring harnesses (a) into the receptacles on the motor. Plug the small, male wiring harness (b) into the female wiring harness from the motor shaft. 2 Align the bolt holes on the extension tube with the holes on the motor shaft, and then secure the tube with the provided hardware and wrenches. Mounting Hardware: c. M8 bolt d. M8 washer e.
7 SECURE THE LOWER COVER c b a 14 REV.
1 Place the lower cover ring (a) around the extension tube, resting it evenly on the motor. There should be a very small gap between the cover and the airfoils. Rotate the cover ring clockwise until it stops. 2 Thread the wires through the opening in the lower cover trim (b), and then slide the trim down the extension tube, resting it evenly on the cover ring. 3 Align the screw holes on the trim with the motor screw holes, and then secure the trim in place with the provided screws (c).
8 ARRANGE LED DIFFUSER RING, WIRING COVER, AND MOUNTING BALL c b a 16 Do not seat the LED diffuser ring in the wiring cover at this step! REV.
Do not seat the LED diffuser ring in the wiring cover at this step! Slide the LED diffuser ring (a), wiring cover (b), and mounting ball (c) down the extension tube (in that order), resting them on the fan hub.
9 ATTACH THE MOUNTING BALL SEAT MOUNTING BALL INSTALL WEDGE c a b 1 18 Inner slot 2 REV.
1 Insert the steel pin (a) into the hole at the top of the extension tube, and then slide the mounting ball upward, seating the steel pin in the inner slots of the ball. Mounting Ball Hardware: a. Steel pin 2 Insert the wedge (b) into the mounting ball as shown, and then secure the wedge with the screw (c). Tighten the screw enough to prevent movement between the mounting ball and extension tube. Do not over-tighten the screw. Mounting Ball Hardware: b. Wedge c.
10 HANG THE FAN Rib Slot 20 REV.
1 Raise the fan to the mounting bracket. Align the slot in the mounting ball with the rib in the mounting bracket, insert the mounting ball, and let the fan hang freely. 2 Gently twist the extension tube to ensure the mounting ball is properly seated and will not move during fan operation.
11 INSTALL THE UPPER EARTH/GROUND WIRE b c a 22 REV.
Route the ground wire from the extension tube (a) to the outside of the mounting bracket. Secure the ground wire terminal (b) to the mounting bracket with the screw (c). Safety Cable Installation You may be required to secure the fan directly to the building structure if your local safety code requires it. Check your local code! Refer to the Safety Cable instructional sheet included with this guide for more information.
AC HOT /L1 AC NEU TRA L/L2 PE/E ART HG ROU ND 12 WIRE THE FAN BLACK a GREEN WHITE 24 REV.
! Make sure power is disconnected before wiring the fan! ! Do not connect the fan to a damaged power source! Do not attempt to resolve electrical failures on your own. Consult a qualified electrician if uncertain of the electrical installation of this fan. 1 Make the electrical connections by securing the supply power wires to the loose ends of the wiring harness (a) with the provided wire nuts. 2 Test the connection by lightly tugging on the wires.
13 INSTALL THE CONTROL BOX SEAT LED INDICATOR INSERT CONTROL BOX a b 1 26 2 REV.
1 Insert the control box (a) into the mounting bracket as illustrated. Be careful not to pinch the wires between the mounting bracket and control box! 2 Snap the LED indicator (b) into the gap in the mounting bracket. Make sure it is securely seated.
14 CONNECT THE CONTROL BOX CONNECT SUPPLY POWER HARNESS CONNECT WIRING HARNESSES e d c b a 1 28 2 REV.
1 Connect the wiring harness from the control box (a) to the harness from the junction box (b). Peel the backing off the double-sided tape (c) on the mounting bracket, and then affix the harnesses to the tape. 2 Connect the wiring harnesses from the extension tube (d) to the corresponding receptacles (e) on the control box.
15 INSTALL THE WIRING COVER ALIGN WIRING COVER INSTALL SCREWS INSTALL DIFFUSER RING b b c a d 1 30 View from below 2 3 REV.
1 Slide the wiring cover (a) up the extension tube, aligning the yellow arrow stickers so that the top of the wiring cover sits flush with the mounting bracket. Make sure the LED indicator receptacle shows through the opening in the cover (b). 2 Make sure all wiring is tucked into the wiring cover, and then secure the cover with the provided screws (c). Wiring Cover Hardware: c.
16 TEST THE FAN Do not expose the remote control to rain or water. Before using the remote control, remove the plastic tab from the battery tray. Turn on power to the fan location and test functionality using the remote. Turn on the fan and test speed and light brightness*. Turns fan on or off. Sets fan timer length of up to eight hours. Each press extends timer by one hour. Turns light on or off. Clears active fan timer. Increases fan speed/light brightness.
United States 2348 Innovation Drive Lexington, KY 40511 haikuhome.com +1 855 694 2458 Canada 6300 Northwest Dr, Unit 3 Mississauga, ON L4V 1J7, Canada haikuhome.com +1 844 424 5848 Mexico CEBSA (Corporación Eléctrica del Bravo SA de CV) Avenida Ind. Rio San Juan Lote 3-A Parque Industrial del Norte Reynosa, Tamps C.P. 88736 http://cebsainc.com/ +52 1 899 925 6398 © 2015 Big Ass Fans The information contained in this document is subject to change without notice.
LP HKU-INST-63-ENG-01