INSTALLATION GUIDE L Series INSTALLATION GUIDE
Visit www.haikuhome.com/service to watch videos of the installation process.
Installation Guide Topic Page Technical Specifications Tools Needed Parts Hardware Prepare the Fan Site Install Your Fan 2 2 3 4 5 6 READ AND SAVE THESE INSTRUCTIONS
! Disconnect power to the fan location before installing the fan! Do not use the fan with a dimmer switch! ! If required by your local electrical code, a licensed electrician must install the fan. Technical Specifications Model Operating voltage Diameter Weight Operating frequency L3127-X5 120 VAC, 1 Φ 52 in.
PARTS a c See the following page for hardware. a Mounting Bracket b Control Box c Wiring Cover d LED Diffuser Ring e Mounting Ball & Hardware† f Lower Cover Trim g Lower Cover Ring h Extension Tube†† i Motor Unit j (3) Airfoils k Remote Control l Hardware Pack b d e f m g l h m Wiring Harness††† k j i † See Hardware page †† Two lengths provided ††† Packaged with control box HAIKU® HOME ● WWW.HAIKUHOME.
HARDWARE Hardware and tools needed for installation are packaged in the hardware pack. Hardware below shown at actual size. Lower Cover Hardware Airfoil Hardware Wiring Cover Hardware or White (6) M5 Screws with Tooth Washer Mounting Hardware Black (2) Painted M3.5 Screws (4) M4 Socket Head Cap Screws Mounting Ball & Hardware Wedge M8 Bolt 4 M8 Washer M8 Nylock Nut 4 mm Self-Tapping Screw Steel Pin Mounting Ball REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 PREPARE THE FAN SITE Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable performing electrical work! 1 Disconnect Power! 2 Outlet Box 3 Black Fans Only If you are installing your fan to an outlet box, it must be suitable for fan support. For softer lighting, remove the white lens and install the smoky lens before attaching the airfoils. If there is not an outlet box at the fan location, install one on a ceiling joist or beam. 1.
2 CONNECT THE WIRING HARNESS Do not connect the green (Earth/Ground) wire on the wiring harness at this step! BLACK GREEN PE/EARTH GROUND TE HI W AC HOT/L1 a AC NEUTRAL/L2 6 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
! Make sure power is disconnected before wiring the fan! ! Do not connect the fan to a damaged power source! Do not attempt to resolve electrical failures on your own. Consult a qualified electrician if uncertain of the electrical installation of this fan. 1 Make the electrical connections by securing the supply power wires to the loose ends of the wiring harness (a) with the provided wire nuts. 2 Test the connection by lightly tugging on the wires.
3 INSTALL THE MOUNTING BRACKET ATTACH MOUNTING BRACKET CONNECT EARTH/GROUND WIRES b d a f e Installation may vary. Refer to the outlet box instructions. c 1 8 2 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
Make sure power is disconnected before installing the mounting bracket! ! 1 Secure the mounting bracket (a) to the outlet box (b) with the screws supplied with the outlet box (c). Outlet Box Hardware: c. Screw (supplied with outlet box) 2 Use a wire nut to secure the supply ground wire (d) to the ground wires from the wiring harness (e) and the mounting bracket (f). Tuck the wiring and wire nuts into the junction box so that only the wiring harness hangs through.
4 INSTALL THE AIRFOILS Make sure the stickers on the airfoils match the stickers on the fan hub! c a b 10 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
Rest the motor assembly (a) on your lap. Moving clockwise, install each airfoil (b) with the provided hardware. Securely tighten the screws. Airfoil Hardware: c. (6) M5 screws with tooth washer STEP COMPLETED HAIKU® HOME ● WWW.HAIKUHOME.
5 INSTALL THE LOWER EARTH/GROUND WIRE POSITION EXTENSION TUBE SECURE EARTH/GROUND WIRE a b c d 1 12 2 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Lower the extension tube (a) onto the motor shaft. Ensure the yellow arrow sticker on the extension tube is aligned with the sticker on the motor. 2 Remove the screw and ground tag from the motor shaft. Secure the Earth/Ground wire to the motor shaft with the captive screw (b). Connect the yellow Earth/Ground female spade connector (c) to the male connector (d) on the motor.
6 CONNECT MOTOR WIRING AND SECURE EXTENSION TUBE INSTALL WIRING HARNESSES SECURE HARDWARE REMOVE SLACK d a b e a c 1 14 2 3 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Remove the tie holding the wiring harnesses to the extension tube. Plug the two large wiring harnesses (a) into the receptacles on the motor. Plug the small, male wiring harness (b) into the female wiring harness from the motor shaft. 2 Align the bolt holes on the extension tube with the holes on the motor shaft, and then secure the tube with the provided hardware and wrenches. Mounting Hardware: c. M8 bolt d. M8 washer e.
7 SECURE THE LOWER COVER c b a 16 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Place the lower cover ring (a) around the extension tube, resting it evenly on the motor. There should be a very small gap between the cover and the airfoils. Rotate the cover ring clockwise until it stops. 2 Thread the wires through the opening in the lower cover trim (b), and then slide the trim down the extension tube, resting it evenly on the cover ring. 3 Align the screw holes on the trim with the motor screw holes, and then secure the trim in place with the provided screws (c).
8 ARRANGE LED DIFFUSER RING, WIRING COVER, AND MOUNTING BALL c b a 18 Do not seat the LED diffuser ring in the wiring cover at this step! REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
Do not seat the LED diffuser ring in the wiring cover at this step! Slide the LED diffuser ring (a), wiring cover (b), and mounting ball (c) down the extension tube (in that order), resting them on the fan hub. STEP COMPLETED HAIKU® HOME ● WWW.HAIKUHOME.
9 ATTACH THE MOUNTING BALL SEAT MOUNTING BALL INSTALL WEDGE c a b 1 20 2 Inner slot REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Insert the steel pin (a) into the hole at the top of the extension tube, and then slide the mounting ball upward, seating the steel pin in the inner slots of the ball. Mounting Ball Hardware: a. Steel pin 2 Insert the wedge (b) into the mounting ball as shown, and then secure the wedge with the screw (c). Tighten the screw enough to prevent movement between the mounting ball and extension tube. Do not over-tighten the screw. Mounting Ball Hardware: b. Wedge c.
10 HANG THE FAN Rib Slot 22 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Raise the fan to the mounting bracket. Align the slot in the mounting ball with the rib in the mounting bracket, insert the mounting ball, and let the fan hang freely. 2 Gently twist the extension tube to ensure the mounting ball is properly seated and will not move during fan operation. STEP COMPLETED HAIKU® HOME ● WWW.HAIKUHOME.
11 INSTALL THE UPPER EARTH/GROUND WIRE c b a 24 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
Route the ground wire from the extension tube (a) to the outside of the mounting bracket as illustrated. Secure the ground wire terminal (b) to the mounting bracket with the captive ground screw (c). Safety Cable Installation You may be required to secure the fan directly to the building structure if your local safety code requires it. Check your local code! Refer to the Safety Cable instructional sheet included with this guide for more information.
12 INSTALL THE CONTROL BOX SEAT LED INDICATOR INSERT CONTROL BOX a b 1 26 2 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Insert the control box (a) into the mounting bracket as illustrated. Be careful not to pinch the wires between the mounting bracket and control box! 2 Snap the LED indicator (b) into the gap in the mounting bracket. Make sure it is securely seated. STEP COMPLETED HAIKU® HOME ● WWW.HAIKUHOME.
13 CONNECT THE CONTROL BOX CONNECT SUPPLY POWER HARNESS CONNECT WIRING HARNESSES e d c b a 1 28 2 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Connect the wiring harness from the control box (a) to the harness from the junction box (b). Peel the backing off the double-sided tape (c) on the mounting bracket, and then affix the harnesses to the tape. 2 Connect the wiring harnesses from the extension tube (d) to the corresponding receptacles (e) on the control box. STEP COMPLETED HAIKU® HOME ● WWW.HAIKUHOME.
14 INSTALL THE WIRING COVER ALIGN WIRING COVER INSTALL SCREWS INSTALL DIFFUSER RING b b c a d 1 30 View from below 2 3 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
1 Slide the wiring cover (a) up the extension tube, aligning the yellow arrow stickers so that the top of the wiring cover sits flush with the mounting bracket. Make sure the LED indicator receptacle shows through the opening in the cover (b). 2 Make sure all wiring is tucked into the wiring cover, and then secure the cover with the provided screws (c). Wiring Cover Hardware: c.
15 TEST THE FAN Do not expose the remote control to rain or water. Turn on the fan Turn on the light Before using the remote control, remove the plastic tab from the battery tray. Turn on power to the fan location and test functionality using the remote. Turn on the fan and test speed and light brightness. 32 REV. A ● © 2016 HAIKU HOME. ALL RIGHTS RESERVED.
© 2016 Haiku Home The information contained in this document is subject to change without notice. May be protected by one or more patents listed at www.bigasssolutions.com/patents Haiku is a trademark of Delta T Corporation, registered in the U.S. and/or other countries.
HKU-INST-101-ENG-01