PR-V7PI
INTRODUCTION Thank you for purchasing the PR-V7PI. Your new Power Distribution Unit (PDU) by Big Dog Power provides filtered AC power to your equipment. 6 individually controlled outlets provide up to 2040 Joules of surge Protection. Wi-Fi and Wired LAN connections give flexibility with placement and network connectivity. The built in Self-Healing functions of the PR-V7PI will keep your network connected equipment going by automatically resetting the power going to the outlet.
J. Recessed Reset button K. Configurable Power Button L. Outlet Status LEDs a. See LED functions for more information M. Loop Out Outlet a. NOTE: This outlet is NOT surge protected, it is intended to be used with additional PR-V7PI units. N. 15-amp Circuit Breaker O. IEC Power Input 120v P. Traditional Vertical Rack Clips a. These Clips use the groove on the back of the PR-V7PI Q. Vertical Rack Ear mounting locations a.
INSTALLATION Rack Mount 1U Horizontal Step 1) Step 2) Step 3) Use the included screws to attach the Rack Mount ears to the PDU near the face of the PDU Slide the PDU into the rack where you intend to mount it Secure the PDU using the appropriate screws for your rack Rack Mount Step 1 Rack Mount Step 2 Rack Mount Vertical with Clips Step 1) Use the included bolt and nuts and secure the included clip to the rack at appropriate lengths apart. a) No further than the length of the PDU (44cm, 17.
Vertical Rack Mount Step 1 Vertical Rack Mount Step 1 Vertical Rack Mount Step 3 Vertical Rack Mount Step 2 Surface Mount Step 1) Use the included screws to attach the included Rack Mount ears to PDU a) Additional Mounting holes can be found at either end and along the side of the PDU Step 2) Install appropriate surface mount screws (not included) through the Rack Mount ears into the desired surface CONNECTIONS and USE Surface Mount Step 1 Surface Mount Step 2 Physical Connections Step 1) Screw in t
Wi-Fi Setup If using the Wi-Fi connection, follow these instructions Step 1) Plug in the included power cable to the PDU and to the AC mains outlet on the wall. a) Wait approximately 15-30 seconds, the power button will begin to flash. Step 2) Scan for Wi-Fi on your Wi-Fi enabled device with a web browser Step 3) Connect to the Wi-Fi SSID of the PDU a) The SSID of the PDU will be “Metra-xxxxxxxxxxxx” where the “x” are the MAC address or device ID of the PDU.
Cloud setup Step 1) Log in to your MAVbase.com account Step 2) Click the Add New button a) Then click “ADD PDU” Step 3) Add the PR-V7PI to your account using the MAC address of the PDU Surge Protection Protected Circuit(s) Replaceable 2040 Total Joule Protection from the Line to Neutral to Ground circuit. For use only with SPD Modules specified by the manufacturer. This SPD is suitable for use only with manufacturer’s specified Cat. No. PR-RMS1 replaceable SPD Module.
Do not cover this device with a cloth. Do not install it on a carpet or rug. Caution – Potential injury Do not use this product with extension cords, multioutlet power strips, multioutlet extenders, or UPS devices (other than a Big Dog Power UPS). The power capacity of these accessories can be overloaded by this product and may result in a risk of fire, or property damage.
Caution – Proper cleaning In general, the only cleaning necessary for is a light dusting. Unplug the PDU from the wall outlet before cleaning it. Do not use liquid or aerosol cleaners. FCC WARNING WARNING!! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
This radio transmitter [27941-PRV7PI] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. NO. Antenna Type Model Name Gain (Peak) 1.
