Hiking Equipment User Manual

CR3901-S THE ULTRA-VIEW

™

WARNING! Read the WEIGHT RESTRICTION WARNING, USAGE INSTRUCTIONS

WARNINGS and FULL-BODY FALL ARREST HARNESS USAGE INSTRUCTIONS

& WARNINGS

on pages 4-17 prior to assembly of this product! Failure to follow

the instructions on this page and pages 4-17 may result in serious injury or death!

WARNING! DO NOT over tighten the hardware. Over tightening can lead to

structural damage and may negatively affect the performance of your stand.

Failure to follow these instructions may result in serious injury or death!

Refer to pages 88-95, Field Installation-Ladderstands, for installation instructions.

NOTE: Steps 1-11 require you to temporarily finger tighten nuts to ensure proper

alignment. All bolts should be installed from the inside with nylock nuts on the outside.

STEP 1. First, attach the left foot platform to the right foot platform using (3)

1/4" x 2 1/2" hex bolts [L] and (3) 1/4" nylock nuts to secure. (fig. 1)

STEP 2. Next attach the top ladder section and foot rest to the left/right foot

platforms using (2) 1/4" x 1 3/4" hex bolts [A], (4) nylon washers and (2) 1/4"

nylock nuts. (fig. 1)

STEP 3. Using (2) 5/16" x 2 1/2" hex bolts [I] and (2) 5/16" nylock nuts attach the

left outer foot platform to the left foot platform. Repeat for right side. (fig.1)

STEP 4. Attach the platform support to the left/right foot platforms using (4)

1/4" x 3" hex bolts [B] and (4) 1/4" nylock nuts. NOTE: The seat hub bracket on

the platform support should be toward the rear of the unit. (fig. 2)

STEP 5. Attach the seat hub to left/right foot platforms using (2) 5/16" x 1 3/4"

hex bolts [F] and (2) 5/16" nylock nuts. Then, attach the seat hub to the seat

hub bracket using (2) 5/16" x 3/4" hex bolts [C]. (fig. 2)

STEP 6. Insert the seat post into the seat hub. Then assemble the seat platform

onto the seat post. NOTE: (2) 4" nylon washers should be added between seat post

and seat hub and between seat post and seat platform. Using (2) 5/16" x 1 1/4"

hex bolts [D] and (2) 5/16" nylock nuts attach the backrest to the seat platform

at desired height. (fig. 2)

STEP 7. Next attach the platform gussets to the outside of the left and right outer

foot platforms and to the inside of the top ladder section using (4) 5/16" x 2 1/4"

hex bolts [H] and (4) 5/16" nylock nuts. (fig. 3)

STEP 8. Next attach the left/right under support gussets to the platform support

using (2) 5/16" x 1 1/4" hex bolts [D] and (2) 5/16" nylock nuts. Then, attach the

left/right under support gussets to the outside of the top ladder section using (2)

1/4" x 2 1/4" hex bolts [K] and (2) 1/4" nylock nuts. (fig. 3)

STEP 9. Attach the rail supports to the left and right foot platforms and left

and right outer foot platforms using (8) 5/16" x 1 1/2" hex bolts [E] and (8)

5/16" nylock nuts. Then attach the rear rail supports in the same method using

(4) 5/16" x 1 1/2" hex bolts [E] and (4) 5/16" nylock nuts to secure. (fig. 4)

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.

This Instruction Manual complies with the Treestand Manufacturers Association’s

TMS 04 - Standard Practice for Treestand Instructions & TMS 02 - Standard Test Method for Treestand Fall Arrest Systems

! /# 1$-&$-2$+#$('