Technical Specs
EWE Module
Technical Specification
Autor: Sc / Fa
Datum: 22.09.2017
Updated: 05.02.2018
EWE Module Technical Specification 13 / 16
8 FCC Statements
BIG KAISER will ship every tool with this FCC statements on a separate leaflet. The end product is a
Class A device: Business to Business only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Caution: Radio Frequency Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least
0.43 cm or more away from person´s body in normal use position.
WARING: (Part 15.21): Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Notes (ISED):
(EN) This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(FR) Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionne-
ment est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit ac-
cepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
(EN) Radio frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development (ISED) radio
frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact
during normal operation is minimized.
This device has also been evaluated and shown compliant with the ISED RF Exposure limits under mobile exposure condi-
tions (antennas at least 0.58cm from a person‘s body).
(FR) Informations concernant l'exposltion aux fréquences radio (RF)
La puissance de sortie émise par l'appareil de sans fiI est inférieure à la limite d'exposition aux fréquences radio d’Innova-
tion, Sciences et Développement économique Canada (ISDE). Utilisez l'appareil de sans fil de façon à minimiser les con-
tacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'ISDE dans des conditions
d'exposition à des appareils mobiles (les antennes se situent à
moins de 20cm du corps d'une personne).
8.1 OEM Statement for Host Integration
The module is assembled only in the assembly department of the company BIG KAISER.
It is not permitted to buy the module only. Customers can only buy the final end product.
The process of assembly is documented in chapter 9: Assembly Process.