Installation Guide

ManualsBrandsBiggies ManualsDoors & Windows120 in. x 60 in. Window Well Scene - Coast Light

PPLICATION INSTRUCTIONS

STEP 1: PREPARE

Clean out debris in the window well and remove a few inches of rock or other material from the bottom

of the window well; this will enable you to roll the panel into place with greater ease when installing it

and will put the lower edge below the rocks when they are replaced which will anchor it. Measure your

window well in several places from the top to the bottom (height) and from side to side (width) to

check for plumb. Caution: Be generous with your measurements; the curved dimension may be

difficult to measure perfectly. You can always trim more off, but you can't add any back! Clean the

metal or concrete with rubbing alcohol or other appropriate solvent to

remove any residue where the

adhesive strips will be placed. If your window well is especially

deep, plan so that about one inch of

rock covers the bottom edge of the liner. Don't be concerned if the liner doesn't reach the top rim of

the well; the top cannot be seen from the room.

STEP 2: CROP

Lay out your Window Well Scenes

image side up on a flat surface. Anchor the corners with

something heavy if needed. Mark your window well measurements to select the area that looks

best for your window well.

STEP 3: TRIM

Using a straight edge and a sharp blade/utility knife, or using appropriate scissors, carefully cut

along the lines you made in step 2. Protect the surface underneath the panel with a piece of wood

or cardboard to avoid damage from the blade. Place the liner into the window well along the curve

to make any final size adjustments.

STEP 4: ATTACH

Attach the individual paired hook & loop fasteners to the window well on the ridges that bump

out toward the room. Avoid placing pieces on wet

or rusted areas. Leaving the male and female

sides connected as well as the backing paper, attach the strips to the metal. Put four pieces down

each side being sure to hit the spots where the corners will be, four down the middle, and three

down each curve. Put the remaining two pieces along the top edge. Starting on the free side of

the rolled liner, remove the remaining backing paper from a set of fasteners. Start rolling out the

liner, and rub on the liner where the fasteners are.

STEP 5: FINISH

Replace the rock or other material in the bottom

of the well to cover the bottom edge of the liner and

add any additional decoration desired such as larger

rocks, driftwood, or plants. Stand back and admire

the dramatic change in your view. Enjoy!

Important note:

Removing or covering up an escape ladder

is NOT recommended, please use your own judgement.

indow well covers or grates are recommended for more years of enjoyment of your Window Well Scenes

product.

When applying in extreme cold temperatures (

º degrees or colder), Hook & Loof fasteners may not adhere to window wells, test before applying.

For Video Instructions on installation, please go to

www.YOUTUBE.com

and type in

Biggies Window Well Scenes

PRODUCT LIMITED WARRANTY

The product is warranted by Biggies, Inc. for two years from date of retail purchase to be free of manufacturer's defects in material and/or workmanship, including fading of the original image. Components and materials

not manufactured by Biggies, Inc. are warranted only to the extent of the original manufacturer's warranty. The sole obligation of Biggies Inc. under this limited warranty is to replace or repair FOB Denver, at the option of

Biggies, Inc., any part which, in the sole opinion of Biggies, Inc., is defective. Under no circumstances will Biggies, Inc. be responsible for mis-installation of the product.

This warranty is made in lieu of all other warranties, expressed or implied, including, but not limited to, any implied warranty of merchantability and/or fitness for a particular purpose or use. There are no warranties express

or implied beyond the description of the product on the original product packaging. Biggies Inc. expressly disclaims liability for incidental, special, or consequential damages of any nature. Biggies, Inc. specifically disclaims

any liability arising from owner's failure to maintain the product. Replacement of parts or modification of the original product will void this warranty.

Biggies, Inc. neither assumes nor authorizes any person or entity to assume for it any obligations or liabilities not expressly stated herein

CEMENT METAL