Installation Guide

Tools Required
• 3/8”or1/2”electricdrill
• Centerpunch
• 7/32”DrillBit
• 9/32”DrillBit
• 3/4”DiameterMetalHoleSaw
• PhillipsHeadScrewDriver
• AdjustableWrench
• Hammer
• File
Parts List
(6)#10-24x3/4”RoundHeadMachineScrews
(6)#10-24Locknuts
(4)1/4-20x3/4”RibbedNeckCarriageBolts
(4)1/4-20LockNuts
(4)NeopreneWashers
(1)LockMountingBracket
(1)LockCylinderwith(2)Keys
(1)3/4”I.D.CylinderLockWasher
(1)RubberDustCap
(1)CylinderRetainer(1-1/2”x4”x14gauge)
(1)LockHandle
(1)LockHandleGasket
(1)LockAssembly
(2)BlackPlasticShaftCaps
(1)BlackPlasticLockReleaseCap
(1)InstallationTemplate
(1)PartsListwithExplodedViewofAssembly
Basement Door Lock Kit
Installation Instructions
Installation Instructions
(Seedrawingonreverseside)
Step 1Tapeholetemplatetorighthanddoor18-1/2”fromthe
bottomofthedoorleafasshownonthetemplate.Centerpunchall
holes.Note:Accuracyisessentialforeaseofinstallation.Remove
template.Drillholestoindicatedsizesontemplateandleany
roughedges.
Step 2Insertlockcylinderthrough3/4”rubberdustcapas
shownondrawing.Placecylinder(withdustcap),handle(with
gasket)and(2)#10-24x3/4”roundheadmachinescrewsthrough
thetopsideofthedoorleaf.Makesurethatthedustcap’shinge
isatthe12o’clockposition.Fromthebottomside,installthesteel
cylinderretainerfollowedby(2)#10locknutsforthehandleand
the3/4”lockwasherandnutforthecylinder.Tightennuts.
Step 3Mountlockassemblytothesteelmountingbracketusing
(4)#10-24x3/4”roundheadmachinescrewsand(4)#10-24lock
nuts.Donottightenscrewsuntilstep5.
Step 4Installmountingbracketandlockassemblyonthe
undersideofthedoorleafusing(4)1/4-20x3/4”ribbedneckcar-
riagebolts,neoprenewashersand1/4-20locknutsasindicatedon
drawing.Carriageboltsshouldbetightenedenoughtoslightlycom-
presstheneoprenewashers.Note:Withthelockslideboltinthe
unlockedposition,theturnhandleshouldbealignedinahorizontal
positionasviewedfromthetopsideofthebasementdoor.
Step 5Installblackplasticcapsasshownonthedrawing.Test
lockoperationwiththedoorintheopenpositionbeforelocking
closeddoor.Forbestoperation,lubricateasrequired.
Note:ForBILCOdoorsmanufacturedbefore1964,a1/2”deep
notchmustbecutinthecoverreinforcingmembertoaccommo-
datetheslideboltofthenewkeyedlock.SeeSECTIONA-Aon
holetemplate.
Operation
From Outside
ToLock:Turnhandlecounterclockwise.
Tounlock:Opendustcap,insertkey,turnkeyclockwise.
From Inside
ToLock:Pushslidebar.
ToUnlock:Pushreleasetab.
The BILCO Company
Phone:800-854-9724
Email:[e-mail]
Website:www.bilco.com
ABC226R-2.0