Billion SG600R2 Smart Energy Wireless Router Quick Start Guide V1.
Table of Contents CHAPTER 1: Introduction..............................................................................0 Introduction of BEsmart...................................................................1 BEsmart Application ........................................................................2 CHAPTER 2 Installation of Web Manager ....................................................3 2.1 Quick Start ......................................................................................
WARNING Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
WARNING 電磁波曝露量MPE標準值1mW/cm2,送測產品實測值為:0.0392 mW/cm2,本產 品使用建議應距離人體大於 20 cm以上 NCC Warning Statement Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.
Introduction Introduction of BEsmart The issue of environmental protection and energy conservation has been received great attentions since the global warming and energy shortage have become a serious worldwide crisis. Billion BEsmart highlights the importance of energy preservations and managements, and contributes smart solutions for Telco/ISP/SI service providers who dedicate to strengthening customer satisfactions.
BEsmart Application The Billion BILLION SG600R2, ZigBee Wireless Smart Energy Gateway, is a TCP/IP based ZigBee/Wi-Fi appliance designed for users to enjoy real-time power management. Integrated with ZigBee wireless technology, the BILLION SG600R2 can communicate wirelessly with Billion ZigBee-enabled smart device, like SG3015-Tx meter and SG110-A Temperature / Humidity sensor.
CHAPTER 2 Installation of Web Manager The router not only functions as a smart wireless bridge but builds Power Management Application into Web GUI. End users can monitor real time power information and control the Smart Energy Meter through Web GUI remotely. Please be noted that here we just focus on functions that are relevant to the power smart management. Let’s start the configurations. 2.
Step 2: Computer IP setting The default address of BILLION SG600R2 is 10.10.10.252. For the first setting, please modify your PC IP to the recommended IP 10.10.10.100 (ranged from 10.10.10.1 to 10.10.10.251). Step3: Access to BILLION SG600R2 WEB GUI 1. Open your web browser and enter the IP address of your router, which by default is 10.10.10.252, and click “Go”. Then a login window prompt will appear. 2. The default username and password are “admin” and “admin” respectively.
3. Once you have logged in to your BILLION SG600R2, you can begin to set it up according to your requirements. You would see the main page of basic status, including Device Information, Port Status, and WAN information. 4. Time Zone Setting First, set up the time to meet the time zone of your country. Click “Continute”.
5. BILLION SG600R2 provides the WAN interface based on your own backbone router. There are 2 Connect Modes: Ethernet and Wireless Client. EWAN: Your backbone router/cable modem is based on Ethernet base. Wireless Client: Your backbone router or cable modem has the Wi-Fi function. For the detail Configuration, please refer to BILLION SG600R2internet configuration document. 6.
Fixed IP Address (STATIC IP) Your backbone device is xDSL router and your PC IP is based on Static IP. Enter the information provided by your ISP PPPOE If your backbone device is xDSL cable modem, please choose PPPOE. For the detail internet configurations, please refer to BILLION SG600R2internet settings. Click “Continue” to proceed to the next step. 7. After clicking “Continue”, the program would start to save the settings.
8. This is BEsmart Registration for cloud server. Create a username and password and offer the E-mail for the registration, then read the term and check the box “I accept the Term of Service”. Click “Apply” to confirm the application. 11. Congratulations! Your BEsmart cloud server has been successfully registered. All the received power information would be stored on the cloud. Click “Need to Save Flash” button to save your settings. 12. Please wait for 10 seconds for saving the configuration.
. The easy configurations of your device have been finished. Congratulations! Please ensure that the smart wireless bridge and its backbone router/modem are maintained in a connection status or it may result in different power consumption data between measurement and real condition.